diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
index f624dc85d441e5000b8fa0a13abfa78a3e5ce7d2..02d23f15fd867fafe2172a1eb75e60beab51a5c7 100644
--- a/arch/arm/boot/dts/omap3-beagle.dts
+++ b/arch/arm/boot/dts/omap3-beagle.dts
@@ -38,6 +38,57 @@
 		};
 	};
 
+	/* HS USB Port 2 RESET */
+	hsusb2_reset: hsusb2_reset_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "hsusb2_reset";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio5 19 0>;	/* gpio_147 */
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
+	/* HS USB Port 2 Power */
+	hsusb2_power: hsusb2_power_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "hsusb2_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&twl_gpio 18 0>;	/* GPIO LEDA */
+		startup-delay-us = <70000>;
+	};
+
+	/* HS USB Host PHY on PORT 2 */
+	hsusb2_phy: hsusb2_phy {
+		compatible = "usb-nop-xceiv";
+		reset-supply = <&hsusb2_reset>;
+		vcc-supply = <&hsusb2_power>;
+	};
+};
+
+&omap3_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&hsusbb2_pins
+	>;
+
+	hsusbb2_pins: pinmux_hsusbb2_pins {
+		pinctrl-single,pins = <
+			0x5c0 0x3  /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_clk OUTPUT */
+			0x5c2 0x3  /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_stp OUTPUT */
+			0x5c4 0x10b  /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dir INPUT | PULLDOWN */
+			0x5c6 0x10b  /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_nxt INPUT | PULLDOWN */
+			0x5c8 0x10b  /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat0 INPUT | PULLDOWN */
+			0x5cA 0x10b  /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat1 INPUT | PULLDOWN */
+			0x1a4 0x10b  /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat2 INPUT | PULLDOWN */
+			0x1a6 0x10b  /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat3 INPUT | PULLDOWN */
+			0x1a8 0x10b  /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat4 INPUT | PULLDOWN */
+			0x1aa 0x10b  /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat5 INPUT | PULLDOWN */
+			0x1ac 0x10b  /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat6 INPUT | PULLDOWN */
+			0x1ae 0x10b  /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat7 INPUT | PULLDOWN */
+		>;
+	};
 };
 
 &i2c1 {
@@ -65,3 +116,23 @@
 &mmc3 {
 	status = "disabled";
 };
+
+&usbhshost {
+	port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+	phys = <0 &hsusb2_phy>;
+};
+
+&twl_gpio {
+	ti,use-leds;
+	/* pullups: BIT(1) */
+	ti,pullups = <0x000002>;
+	/*
+	 * pulldowns:
+	 * BIT(2), BIT(6), BIT(7), BIT(8), BIT(13)
+	 * BIT(15), BIT(16), BIT(17)
+	 */
+	ti,pulldowns = <0x03a1c4>;
+};
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index 1acc26148ffcf94c1ee605d1db58c531f9b01e26..a14f74bbce7c0079238486899ba3037dcf926c62 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -397,5 +397,36 @@
 			ti,timer-alwon;
 			ti,timer-secure;
 		};
+
+		usbhstll: usbhstll@48062000 {
+			compatible = "ti,usbhs-tll";
+			reg = <0x48062000 0x1000>;
+			interrupts = <78>;
+			ti,hwmods = "usb_tll_hs";
+		};
+
+		usbhshost: usbhshost@48064000 {
+			compatible = "ti,usbhs-host";
+			reg = <0x48064000 0x400>;
+			ti,hwmods = "usb_host_hs";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			usbhsohci: ohci@48064400 {
+				compatible = "ti,ohci-omap3", "usb-ohci";
+				reg = <0x48064400 0x400>;
+				interrupt-parent = <&intc>;
+				interrupts = <76>;
+			};
+
+			usbhsehci: ehci@48064800 {
+				compatible = "ti,ehci-omap", "usb-ehci";
+				reg = <0x48064800 0x400>;
+				interrupt-parent = <&intc>;
+				interrupts = <77>;
+			};
+		};
+
 	};
 };
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 739bb79e410e5bb5f558afdc85d227d9e5056885..b7db1a2b6ca7a9a3200a1087372d9c988dcab5a7 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -529,5 +529,35 @@
 			ti,hwmods = "timer11";
 			ti,timer-pwm;
 		};
+
+		usbhstll: usbhstll@4a062000 {
+			compatible = "ti,usbhs-tll";
+			reg = <0x4a062000 0x1000>;
+			interrupts = <0 78 0x4>;
+			ti,hwmods = "usb_tll_hs";
+		};
+
+		usbhshost: usbhshost@4a064000 {
+			compatible = "ti,usbhs-host";
+			reg = <0x4a064000 0x800>;
+			ti,hwmods = "usb_host_hs";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			usbhsohci: ohci@4a064800 {
+				compatible = "ti,ohci-omap3", "usb-ohci";
+				reg = <0x4a064800 0x400>;
+				interrupt-parent = <&gic>;
+				interrupts = <0 76 0x4>;
+			};
+
+			usbhsehci: ehci@4a064c00 {
+				compatible = "ti,ehci-omap", "usb-ehci";
+				reg = <0x4a064c00 0x400>;
+				interrupt-parent = <&gic>;
+				interrupts = <0 77 0x4>;
+			};
+		};
 	};
 };
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index ce812decfacad108eecdb20174f7c030ffcf5cc5..7eb9651dd0f7e02d7e19c52c3d81d0bfa5cfc8dc 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -445,16 +445,23 @@ static void enable_board_wakeup_source(void)
 		OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
 }
 
+static struct usbhs_phy_data phy_data[] __initdata = {
+	{
+		.port = 1,
+		.reset_gpio = 57,
+		.vcc_gpio = -EINVAL,
+	},
+	{
+		.port = 2,
+		.reset_gpio = 61,
+		.vcc_gpio = -EINVAL,
+	},
+};
+
 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
 
 	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
 	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-	.phy_reset  = true,
-	.reset_gpio_port[0]  = 57,
-	.reset_gpio_port[1]  = 61,
-	.reset_gpio_port[2]  = -EINVAL
 };
 
 #ifdef CONFIG_OMAP_MUX
@@ -606,6 +613,8 @@ static void __init omap_3430sdp_init(void)
 	board_flash_init(sdp_flash_partitions, chip_sel_3430, 0);
 	sdp3430_display_init();
 	enable_board_wakeup_source();
+
+	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 	usbhs_init(&usbhs_bdata);
 }
 
diff --git a/arch/arm/mach-omap2/board-3630sdp.c b/arch/arm/mach-omap2/board-3630sdp.c
index 67447bd4564fbd05c5956ebed41a5de3e10ac3f6..20d6d8189240d3343798833578093d4ae9933f36 100644
--- a/arch/arm/mach-omap2/board-3630sdp.c
+++ b/arch/arm/mach-omap2/board-3630sdp.c
@@ -53,16 +53,23 @@ static void enable_board_wakeup_source(void)
 		OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
 }
 
+static struct usbhs_phy_data phy_data[] __initdata = {
+	{
+		.port = 1,
+		.reset_gpio = 126,
+		.vcc_gpio = -EINVAL,
+	},
+	{
+		.port = 2,
+		.reset_gpio = 61,
+		.vcc_gpio = -EINVAL,
+	},
+};
+
 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
 
 	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
 	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-	.phy_reset  = true,
-	.reset_gpio_port[0]  = 126,
-	.reset_gpio_port[1]  = 61,
-	.reset_gpio_port[2]  = -EINVAL
 };
 
 #ifdef CONFIG_OMAP_MUX
@@ -199,6 +206,8 @@ static void __init omap_sdp_init(void)
 	board_smc91x_init();
 	board_flash_init(sdp_flash_partitions, chip_sel_sdp, NAND_BUSWIDTH_16);
 	enable_board_wakeup_source();
+
+	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 	usbhs_init(&usbhs_bdata);
 }
 
diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c
index 7d3358b2e59369083cd02cbf31d38abb0e3bb282..fc53911d0d13b9842a7efcf28ba4431159df0bc4 100644
--- a/arch/arm/mach-omap2/board-am3517crane.c
+++ b/arch/arm/mach-omap2/board-am3517crane.c
@@ -47,15 +47,17 @@ static struct omap_board_mux board_mux[] __initdata = {
 };
 #endif
 
+static struct usbhs_phy_data phy_data[] __initdata = {
+	{
+		.port = 1,
+		.reset_gpio = GPIO_USB_NRESET,
+		.vcc_gpio = GPIO_USB_POWER,
+		.vcc_polarity = 1,
+	},
+};
+
 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
 	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-	.phy_reset  = true,
-	.reset_gpio_port[0]  = GPIO_USB_NRESET,
-	.reset_gpio_port[1]  = -EINVAL,
-	.reset_gpio_port[2]  = -EINVAL
 };
 
 static struct mtd_partition crane_nand_partitions[] = {
@@ -131,13 +133,7 @@ static void __init am3517_crane_init(void)
 		return;
 	}
 
-	ret = gpio_request_one(GPIO_USB_POWER, GPIOF_OUT_INIT_HIGH,
-			       "usb_ehci_enable");
-	if (ret < 0) {
-		pr_err("Can not request GPIO %d\n", GPIO_USB_POWER);
-		return;
-	}
-
+	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 	usbhs_init(&usbhs_bdata);
 	am35xx_emac_init(AM35XX_DEFAULT_MDIO_FREQUENCY, 1);
 }
diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c
index 9fb85908a61e498a7ae7ec27f18fe2f7b45756db..191f9762ba63c4eb4368b95a862b17228ac5049c 100644
--- a/arch/arm/mach-omap2/board-am3517evm.c
+++ b/arch/arm/mach-omap2/board-am3517evm.c
@@ -274,6 +274,14 @@ static __init void am3517_evm_mcbsp1_init(void)
 	omap_ctrl_writel(devconf0, OMAP2_CONTROL_DEVCONF0);
 }
 
+static struct usbhs_phy_data phy_data[] __initdata = {
+	{
+		.port = 1,
+		.reset_gpio = 57,
+		.vcc_gpio = -EINVAL,
+	},
+};
+
 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
 	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
 #if defined(CONFIG_PANEL_SHARP_LQ043T1DG01) || \
@@ -282,12 +290,6 @@ static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
 #else
 	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
 #endif
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-	.phy_reset  = true,
-	.reset_gpio_port[0]  = 57,
-	.reset_gpio_port[1]  = -EINVAL,
-	.reset_gpio_port[2]  = -EINVAL
 };
 
 #ifdef CONFIG_OMAP_MUX
@@ -349,7 +351,6 @@ static struct omap2_hsmmc_info mmc[] = {
 	{}      /* Terminator */
 };
 
-
 static void __init am3517_evm_init(void)
 {
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
@@ -361,6 +362,8 @@ static void __init am3517_evm_init(void)
 
 	/* Configure GPIO for EHCI port */
 	omap_mux_init_gpio(57, OMAP_PIN_OUTPUT);
+
+	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 	usbhs_init(&usbhs_bdata);
 	am3517_evm_hecc_init(&am3517_evm_hecc_pdata);
 	/* DSS */
diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
index af2bb219e2147d922c95f829e833804f421184b3..7fda3f5f8a7fdf8ce0de057241342333729a8fc8 100644
--- a/arch/arm/mach-omap2/board-cm-t35.c
+++ b/arch/arm/mach-omap2/board-cm-t35.c
@@ -419,15 +419,22 @@ static struct omap2_hsmmc_info mmc[] = {
 	{}	/* Terminator */
 };
 
+static struct usbhs_phy_data phy_data[] __initdata = {
+	{
+		.port = 1,
+		.reset_gpio = OMAP_MAX_GPIO_LINES + 6,
+		.vcc_gpio = -EINVAL,
+	},
+	{
+		.port = 2,
+		.reset_gpio = OMAP_MAX_GPIO_LINES + 7,
+		.vcc_gpio = -EINVAL,
+	},
+};
+
 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
 	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
 	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-	.phy_reset  = true,
-	.reset_gpio_port[0]  = OMAP_MAX_GPIO_LINES + 6,
-	.reset_gpio_port[1]  = OMAP_MAX_GPIO_LINES + 7,
-	.reset_gpio_port[2]  = -EINVAL
 };
 
 static void  __init cm_t35_init_usbh(void)
@@ -444,6 +451,7 @@ static void  __init cm_t35_init_usbh(void)
 		msleep(1);
 	}
 
+	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 	usbhs_init(&usbhs_bdata);
 }
 
diff --git a/arch/arm/mach-omap2/board-cm-t3517.c b/arch/arm/mach-omap2/board-cm-t3517.c
index a66da808cc4ab011d7d97f449bd33f6a51272b4c..6920f6cfc97c30e67ff45d75deb9bcebd59efe25 100644
--- a/arch/arm/mach-omap2/board-cm-t3517.c
+++ b/arch/arm/mach-omap2/board-cm-t3517.c
@@ -188,15 +188,22 @@ static inline void cm_t3517_init_rtc(void) {}
 #define HSUSB2_RESET_GPIO	(147)
 #define USB_HUB_RESET_GPIO	(152)
 
+static struct usbhs_phy_data phy_data[] __initdata = {
+	{
+		.port = 1,
+		.reset_gpio = HSUSB1_RESET_GPIO,
+		.vcc_gpio = -EINVAL,
+	},
+	{
+		.port = 2,
+		.reset_gpio = HSUSB2_RESET_GPIO,
+		.vcc_gpio = -EINVAL,
+	},
+};
+
 static struct usbhs_omap_platform_data cm_t3517_ehci_pdata __initdata = {
 	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
 	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-	.phy_reset  = true,
-	.reset_gpio_port[0]  = HSUSB1_RESET_GPIO,
-	.reset_gpio_port[1]  = HSUSB2_RESET_GPIO,
-	.reset_gpio_port[2]  = -EINVAL,
 };
 
 static int __init cm_t3517_init_usbh(void)
@@ -213,6 +220,7 @@ static int __init cm_t3517_init_usbh(void)
 		msleep(1);
 	}
 
+	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 	usbhs_init(&cm_t3517_ehci_pdata);
 
 	return 0;
diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 53056c3b08362ea6a4c40f8a044f2b146018a1d8..42fbf1ef12a949778107b7a5e8aa76b18638e986 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -437,15 +437,7 @@ static struct platform_device *devkit8000_devices[] __initdata = {
 };
 
 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-
 	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-	.phy_reset  = true,
-	.reset_gpio_port[0]  = -EINVAL,
-	.reset_gpio_port[1]  = -EINVAL,
-	.reset_gpio_port[2]  = -EINVAL
 };
 
 #ifdef CONFIG_OMAP_MUX
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index bf92678a01d061dabd0d857dfb00d83504ce034a..95ccec0eeab919f33101e657147955056c818ca2 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -527,26 +527,28 @@ static void __init igep_i2c_init(void)
 	omap3_pmic_init("twl4030", &igep_twldata);
 }
 
+static struct usbhs_phy_data igep2_phy_data[] __initdata = {
+	{
+		.port = 1,
+		.reset_gpio = IGEP2_GPIO_USBH_NRESET,
+		.vcc_gpio = -EINVAL,
+	},
+};
+
+static struct usbhs_phy_data igep3_phy_data[] __initdata = {
+	{
+		.port = 2,
+		.reset_gpio = IGEP3_GPIO_USBH_NRESET,
+		.vcc_gpio = -EINVAL,
+	},
+};
+
 static struct usbhs_omap_platform_data igep2_usbhs_bdata __initdata = {
 	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-	.phy_reset = true,
-	.reset_gpio_port[0] = IGEP2_GPIO_USBH_NRESET,
-	.reset_gpio_port[1] = -EINVAL,
-	.reset_gpio_port[2] = -EINVAL,
 };
 
 static struct usbhs_omap_platform_data igep3_usbhs_bdata __initdata = {
-	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
 	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-	.phy_reset = true,
-	.reset_gpio_port[0] = -EINVAL,
-	.reset_gpio_port[1] = IGEP3_GPIO_USBH_NRESET,
-	.reset_gpio_port[2] = -EINVAL,
 };
 
 #ifdef CONFIG_OMAP_MUX
@@ -642,8 +644,10 @@ static void __init igep_init(void)
 	if (machine_is_igep0020()) {
 		omap_display_init(&igep2_dss_data);
 		igep2_init_smsc911x();
+		usbhs_init_phys(igep2_phy_data, ARRAY_SIZE(igep2_phy_data));
 		usbhs_init(&igep2_usbhs_bdata);
 	} else {
+		usbhs_init_phys(igep3_phy_data, ARRAY_SIZE(igep3_phy_data));
 		usbhs_init(&igep3_usbhs_bdata);
 	}
 }
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index c3558f93d42c4a3d52f705573be61e156ff59669..5382215a49bc9fa364ce5e255af9ec6a49770fda 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -33,6 +33,7 @@
 #include <linux/mtd/nand.h>
 #include <linux/mmc/host.h>
 #include <linux/usb/phy.h>
+#include <linux/usb/nop-usb-xceiv.h>
 
 #include <linux/regulator/machine.h>
 #include <linux/i2c/twl.h>
@@ -277,6 +278,21 @@ static struct regulator_consumer_supply beagle_vsim_supply[] = {
 
 static struct gpio_led gpio_leds[];
 
+/* PHY's VCC regulator might be added later, so flag that we need it */
+static struct nop_usb_xceiv_platform_data hsusb2_phy_data = {
+	.needs_vcc = true,
+};
+
+static struct usbhs_phy_data phy_data[] = {
+	{
+		.port = 2,
+		.reset_gpio = 147,
+		.vcc_gpio = -1,		/* updated in beagle_twl_gpio_setup */
+		.vcc_polarity = 1,	/* updated in beagle_twl_gpio_setup */
+		.platform_data = &hsusb2_phy_data,
+	},
+};
+
 static int beagle_twl_gpio_setup(struct device *dev,
 		unsigned gpio, unsigned ngpio)
 {
@@ -318,9 +334,11 @@ static int beagle_twl_gpio_setup(struct device *dev,
 	}
 	dvi_panel.power_down_gpio = beagle_config.dvi_pd_gpio;
 
-	gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level,
-			"nEN_USB_PWR");
+	/* TWL4030_GPIO_MAX i.e. LED_GPO controls HS USB Port 2 power */
+	phy_data[0].vcc_gpio = gpio + TWL4030_GPIO_MAX;
+	phy_data[0].vcc_polarity = beagle_config.usb_pwr_level;
 
+	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 	return 0;
 }
 
@@ -453,15 +471,7 @@ static struct platform_device *omap3_beagle_devices[] __initdata = {
 };
 
 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-
-	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
 	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-	.phy_reset  = true,
-	.reset_gpio_port[0]  = -EINVAL,
-	.reset_gpio_port[1]  = 147,
-	.reset_gpio_port[2]  = -EINVAL
 };
 
 #ifdef CONFIG_OMAP_MUX
@@ -543,7 +553,9 @@ static void __init omap3_beagle_init(void)
 
 	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
 	usb_musb_init(NULL);
+
 	usbhs_init(&usbhs_bdata);
+
 	board_nand_init(omap3beagle_nand_partitions,
 			ARRAY_SIZE(omap3beagle_nand_partitions), NAND_CS,
 			NAND_BUSWIDTH_16, NULL);
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 48789e0bb915059ff8b9fb26d5a2712ff095020b..2de92facc8a38234bacec820218fe4143b8b137f 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -496,7 +496,7 @@ struct wl12xx_platform_data omap3evm_wlan_data __initdata = {
 static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = {
 	REGULATOR_SUPPLY("VDD_CSIPHY1", "omap3isp"),	/* OMAP ISP */
 	REGULATOR_SUPPLY("VDD_CSIPHY2", "omap3isp"),	/* OMAP ISP */
-	REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"),
+	REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.2"),	/* hsusb port 2 */
 	REGULATOR_SUPPLY("vaux2", NULL),
 };
 
@@ -539,17 +539,16 @@ static int __init omap3_evm_i2c_init(void)
 	return 0;
 }
 
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
+static struct usbhs_phy_data phy_data[] __initdata = {
+	{
+		.port = 2,
+		.reset_gpio = -1,	/* set at runtime */
+		.vcc_gpio = -EINVAL,
+	},
+};
 
-	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
 	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-	.phy_reset  = true,
-	/* PHY reset GPIO will be runtime programmed based on EVM version */
-	.reset_gpio_port[0]  = -EINVAL,
-	.reset_gpio_port[1]  = -EINVAL,
-	.reset_gpio_port[2]  = -EINVAL
 };
 
 #ifdef CONFIG_OMAP_MUX
@@ -725,7 +724,7 @@ static void __init omap3_evm_init(void)
 
 		/* setup EHCI phy reset config */
 		omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
-		usbhs_bdata.reset_gpio_port[1] = 21;
+		phy_data[0].reset_gpio = 21;
 
 		/* EVM REV >= E can supply 500mA with EXTVBUS programming */
 		musb_board_data.power = 500;
@@ -733,10 +732,12 @@ static void __init omap3_evm_init(void)
 	} else {
 		/* setup EHCI phy reset on MDC */
 		omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
-		usbhs_bdata.reset_gpio_port[1] = 135;
+		phy_data[0].reset_gpio = 135;
 	}
 	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
 	usb_musb_init(&musb_board_data);
+
+	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 	usbhs_init(&usbhs_bdata);
 	board_nand_init(omap3evm_nand_partitions,
 			ARRAY_SIZE(omap3evm_nand_partitions), NAND_CS,
diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index 2bba362148a0c87d12a53d86d5dd5ef2ddbeb4c1..1004d2aaa68f5e29847eeb1691f7e3d909a162d7 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -346,7 +346,7 @@ static struct regulator_consumer_supply pandora_vcc_lcd_supply[] = {
 };
 
 static struct regulator_consumer_supply pandora_usb_phy_supply[] = {
-	REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"),
+	REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.2"),	/* hsusb port 2 */
 };
 
 /* ads7846 on SPI and 2 nub controllers on I2C */
@@ -561,6 +561,14 @@ static void __init pandora_wl1251_init(void)
 	printk(KERN_ERR "wl1251 board initialisation failed\n");
 }
 
+static struct usbhs_phy_data phy_data[] __initdata = {
+	{
+		.port = 2,
+		.reset_gpio = 16,
+		.vcc_gpio = -EINVAL,
+	},
+};
+
 static struct platform_device *omap3pandora_devices[] __initdata = {
 	&pandora_leds_gpio,
 	&pandora_keys_gpio,
@@ -569,15 +577,7 @@ static struct platform_device *omap3pandora_devices[] __initdata = {
 };
 
 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-
-	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
 	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-	.phy_reset  = true,
-	.reset_gpio_port[0]  = -EINVAL,
-	.reset_gpio_port[1]  = 16,
-	.reset_gpio_port[2]  = -EINVAL
 };
 
 #ifdef CONFIG_OMAP_MUX
@@ -601,7 +601,10 @@ static void __init omap3pandora_init(void)
 	spi_register_board_info(omap3pandora_spi_board_info,
 			ARRAY_SIZE(omap3pandora_spi_board_info));
 	omap_ads7846_init(1, OMAP3_PANDORA_TS_GPIO, 0, NULL);
+
+	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 	usbhs_init(&usbhs_bdata);
+
 	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
 	usb_musb_init(NULL);
 	gpmc_nand_init(&pandora_nand_data, NULL);
diff --git a/arch/arm/mach-omap2/board-omap3stalker.c b/arch/arm/mach-omap2/board-omap3stalker.c
index 95c10b3aa678a5321be115c91a353a8296405168..bf095648989933ca0c0171ff661fc998a704a96b 100644
--- a/arch/arm/mach-omap2/board-omap3stalker.c
+++ b/arch/arm/mach-omap2/board-omap3stalker.c
@@ -358,19 +358,20 @@ static int __init omap3_stalker_i2c_init(void)
 
 #define OMAP3_STALKER_TS_GPIO	175
 
+static struct usbhs_phy_data phy_data[] __initdata = {
+	{
+		.port = 2,
+		.reset_gpio = 21,
+		.vcc_gpio = -EINVAL,
+	},
+};
+
 static struct platform_device *omap3_stalker_devices[] __initdata = {
 	&keys_gpio,
 };
 
 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
 	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-	.phy_reset = true,
-	.reset_gpio_port[0] = -EINVAL,
-	.reset_gpio_port[1] = 21,
-	.reset_gpio_port[2] = -EINVAL,
 };
 
 #ifdef CONFIG_OMAP_MUX
@@ -407,6 +408,8 @@ static void __init omap3_stalker_init(void)
 	omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
 	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
 	usb_musb_init(NULL);
+
+	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 	usbhs_init(&usbhs_bdata);
 	omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL);
 
diff --git a/arch/arm/mach-omap2/board-omap3touchbook.c b/arch/arm/mach-omap2/board-omap3touchbook.c
index bcd44fbcd87785f4332f881d4b23bbb4da7f5d5f..7da48bc42bbfbb2007ac244a594c54299a2eb13d 100644
--- a/arch/arm/mach-omap2/board-omap3touchbook.c
+++ b/arch/arm/mach-omap2/board-omap3touchbook.c
@@ -305,21 +305,22 @@ static struct omap_board_mux board_mux[] __initdata = {
 };
 #endif
 
+static struct usbhs_phy_data phy_data[] __initdata = {
+	{
+		.port = 2,
+		.reset_gpio = 147,
+		.vcc_gpio = -EINVAL,
+	},
+};
+
 static struct platform_device *omap3_touchbook_devices[] __initdata = {
 	&leds_gpio,
 	&keys_gpio,
 };
 
 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-
 	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
 	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
-	.phy_reset  = true,
-	.reset_gpio_port[0]  = -EINVAL,
-	.reset_gpio_port[1]  = 147,
-	.reset_gpio_port[2]  = -EINVAL
 };
 
 static void omap3_touchbook_poweroff(void)
@@ -368,6 +369,8 @@ static void __init omap3_touchbook_init(void)
 	omap_ads7846_init(4, OMAP3_TS_GPIO, 310, &ads7846_pdata);
 	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
 	usb_musb_init(NULL);
+
+	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 	usbhs_init(&usbhs_bdata);
 	board_nand_init(omap3touchbook_nand_partitions,
 			ARRAY_SIZE(omap3touchbook_nand_partitions), NAND_CS,
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index b02c2f00609b275ad50ae9cb91e9c15ad0ca6975..a71ad345f20d8129788244dcfebd0864e396bd88 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -31,6 +31,7 @@
 #include <linux/ti_wilink_st.h>
 #include <linux/usb/musb.h>
 #include <linux/usb/phy.h>
+#include <linux/usb/nop-usb-xceiv.h>
 #include <linux/wl12xx.h>
 #include <linux/irqchip/arm-gic.h>
 #include <linux/platform_data/omap-abe-twl6040.h>
@@ -132,6 +133,22 @@ static struct platform_device btwilink_device = {
 	.id	= -1,
 };
 
+/* PHY device on HS USB Port 1 i.e. nop_usb_xceiv.1 */
+static struct nop_usb_xceiv_platform_data hsusb1_phy_data = {
+	/* FREF_CLK3 provides the 19.2 MHz reference clock to the PHY */
+	.clk_rate = 19200000,
+};
+
+static struct usbhs_phy_data phy_data[] __initdata = {
+	{
+		.port = 1,
+		.reset_gpio = GPIO_HUB_NRESET,
+		.vcc_gpio = GPIO_HUB_POWER,
+		.vcc_polarity = 1,
+		.platform_data = &hsusb1_phy_data,
+	},
+};
+
 static struct platform_device *panda_devices[] __initdata = {
 	&leds_gpio,
 	&wl1271_device,
@@ -142,49 +159,19 @@ static struct platform_device *panda_devices[] __initdata = {
 
 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
 	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-	.phy_reset  = false,
-	.reset_gpio_port[0]  = -EINVAL,
-	.reset_gpio_port[1]  = -EINVAL,
-	.reset_gpio_port[2]  = -EINVAL
-};
-
-static struct gpio panda_ehci_gpios[] __initdata = {
-	{ GPIO_HUB_POWER,	GPIOF_OUT_INIT_LOW,  "hub_power"  },
-	{ GPIO_HUB_NRESET,	GPIOF_OUT_INIT_LOW,  "hub_nreset" },
 };
 
 static void __init omap4_ehci_init(void)
 {
 	int ret;
-	struct clk *phy_ref_clk;
 
 	/* FREF_CLK3 provides the 19.2 MHz reference clock to the PHY */
-	phy_ref_clk = clk_get(NULL, "auxclk3_ck");
-	if (IS_ERR(phy_ref_clk)) {
-		pr_err("Cannot request auxclk3\n");
-		return;
-	}
-	clk_set_rate(phy_ref_clk, 19200000);
-	clk_prepare_enable(phy_ref_clk);
-
-	/* disable the power to the usb hub prior to init and reset phy+hub */
-	ret = gpio_request_array(panda_ehci_gpios,
-				 ARRAY_SIZE(panda_ehci_gpios));
-	if (ret) {
-		pr_err("Unable to initialize EHCI power/reset\n");
-		return;
-	}
-
-	gpio_export(GPIO_HUB_POWER, 0);
-	gpio_export(GPIO_HUB_NRESET, 0);
-	gpio_set_value(GPIO_HUB_NRESET, 1);
+	ret = clk_add_alias("main_clk", "nop_usb_xceiv.1", "auxclk3_ck", NULL);
+	if (ret)
+		pr_err("Failed to add main_clk alias to auxclk3_ck\n");
 
+	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 	usbhs_init(&usbhs_bdata);
-
-	/* enable power to hub */
-	gpio_set_value(GPIO_HUB_POWER, 1);
 }
 
 static struct omap_musb_board_data musb_board_data = {
diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
index 86bab51154eefe66ba1808f38fa85cef0ceb41e6..ab79a4422bcc6301e63a2d10b5b835cb85ad306f 100644
--- a/arch/arm/mach-omap2/board-overo.c
+++ b/arch/arm/mach-omap2/board-overo.c
@@ -458,14 +458,16 @@ static int __init overo_spi_init(void)
 	return 0;
 }
 
+static struct usbhs_phy_data phy_data[] __initdata = {
+	{
+		.port = 2,
+		.reset_gpio = OVERO_GPIO_USBH_NRESET,
+		.vcc_gpio = -EINVAL,
+	},
+};
+
 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
 	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-	.phy_reset  = true,
-	.reset_gpio_port[0]  = -EINVAL,
-	.reset_gpio_port[1]  = OVERO_GPIO_USBH_NRESET,
-	.reset_gpio_port[2]  = -EINVAL
 };
 
 #ifdef CONFIG_OMAP_MUX
@@ -502,6 +504,8 @@ static void __init overo_init(void)
 			ARRAY_SIZE(overo_nand_partitions), NAND_CS, 0, NULL);
 	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
 	usb_musb_init(NULL);
+
+	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 	usbhs_init(&usbhs_bdata);
 	overo_spi_init();
 	overo_init_smsc911x();
diff --git a/arch/arm/mach-omap2/board-zoom.c b/arch/arm/mach-omap2/board-zoom.c
index 5e4d4c9fe61a4fd6c036e4447bb67d268ff82c8a..1a3dd865d8ebac8aca30ce309f2893eee5bb6462 100644
--- a/arch/arm/mach-omap2/board-zoom.c
+++ b/arch/arm/mach-omap2/board-zoom.c
@@ -92,14 +92,16 @@ static struct mtd_partition zoom_nand_partitions[] = {
 	},
 };
 
+static struct usbhs_phy_data phy_data[] __initdata = {
+	{
+		.port = 2,
+		.reset_gpio = ZOOM3_EHCI_RESET_GPIO,
+		.vcc_gpio = -EINVAL,
+	},
+};
+
 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-	.port_mode[0]		= OMAP_USBHS_PORT_MODE_UNUSED,
 	.port_mode[1]		= OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[2]		= OMAP_USBHS_PORT_MODE_UNUSED,
-	.phy_reset		= true,
-	.reset_gpio_port[0]	= -EINVAL,
-	.reset_gpio_port[1]	= ZOOM3_EHCI_RESET_GPIO,
-	.reset_gpio_port[2]	= -EINVAL,
 };
 
 static void __init omap_zoom_init(void)
@@ -109,6 +111,8 @@ static void __init omap_zoom_init(void)
 	} else if (machine_is_omap_zoom3()) {
 		omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
 		omap_mux_init_gpio(ZOOM3_EHCI_RESET_GPIO, OMAP_PIN_OUTPUT);
+
+		usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 		usbhs_init(&usbhs_bdata);
 	}
 
diff --git a/arch/arm/mach-omap2/usb-host.c b/arch/arm/mach-omap2/usb-host.c
index 5706bdccf45ee34b643141337b38222fbaf5f63a..aa27d7f5cbb7a760596337903fd0e61ac22e647b 100644
--- a/arch/arm/mach-omap2/usb-host.c
+++ b/arch/arm/mach-omap2/usb-host.c
@@ -22,8 +22,12 @@
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 #include <linux/dma-mapping.h>
-
-#include <asm/io.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/fixed.h>
+#include <linux/string.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/usb/phy.h>
 
 #include "soc.h"
 #include "omap_device.h"
@@ -526,3 +530,155 @@ void __init usbhs_init(struct usbhs_omap_platform_data *pdata)
 }
 
 #endif
+
+/* Template for PHY regulators */
+static struct fixed_voltage_config hsusb_reg_config = {
+	/* .supply_name filled later */
+	.microvolts = 3300000,
+	.gpio = -1,		/* updated later */
+	.startup_delay = 70000, /* 70msec */
+	.enable_high = 1,	/* updated later */
+	.enabled_at_boot = 0,	/* keep in RESET */
+	/* .init_data filled later */
+};
+
+static const char *nop_name = "nop_usb_xceiv"; /* NOP PHY driver */
+static const char *reg_name = "reg-fixed-voltage"; /* Regulator driver */
+
+/**
+ * usbhs_add_regulator - Add a gpio based fixed voltage regulator device
+ * @name: name for the regulator
+ * @dev_id: device id of the device this regulator supplies power to
+ * @dev_supply: supply name that the device expects
+ * @gpio: GPIO number
+ * @polarity: 1 - Active high, 0 - Active low
+ */
+static int usbhs_add_regulator(char *name, char *dev_id, char *dev_supply,
+						int gpio, int polarity)
+{
+	struct regulator_consumer_supply *supplies;
+	struct regulator_init_data *reg_data;
+	struct fixed_voltage_config *config;
+	struct platform_device *pdev;
+	int ret;
+
+	supplies = kzalloc(sizeof(*supplies), GFP_KERNEL);
+	if (!supplies)
+		return -ENOMEM;
+
+	supplies->supply = dev_supply;
+	supplies->dev_name = dev_id;
+
+	reg_data = kzalloc(sizeof(*reg_data), GFP_KERNEL);
+	if (!reg_data)
+		return -ENOMEM;
+
+	reg_data->constraints.valid_ops_mask = REGULATOR_CHANGE_STATUS;
+	reg_data->consumer_supplies = supplies;
+	reg_data->num_consumer_supplies = 1;
+
+	config = kmemdup(&hsusb_reg_config, sizeof(hsusb_reg_config),
+			GFP_KERNEL);
+	if (!config)
+		return -ENOMEM;
+
+	config->supply_name = name;
+	config->gpio = gpio;
+	config->enable_high = polarity;
+	config->init_data = reg_data;
+
+	/* create a regulator device */
+	pdev = kzalloc(sizeof(*pdev), GFP_KERNEL);
+	if (!pdev)
+		return -ENOMEM;
+
+	pdev->id = PLATFORM_DEVID_AUTO;
+	pdev->name = reg_name;
+	pdev->dev.platform_data = config;
+
+	ret = platform_device_register(pdev);
+	if (ret)
+		pr_err("%s: Failed registering regulator %s for %s\n",
+				__func__, name, dev_id);
+
+	return ret;
+}
+
+int usbhs_init_phys(struct usbhs_phy_data *phy, int num_phys)
+{
+	char *rail_name;
+	int i, len;
+	struct platform_device *pdev;
+	char *phy_id;
+
+	/* the phy_id will be something like "nop_usb_xceiv.1" */
+	len = strlen(nop_name) + 3; /* 3 -> ".1" and NULL terminator */
+
+	for (i = 0; i < num_phys; i++) {
+
+		if (!phy->port) {
+			pr_err("%s: Invalid port 0. Must start from 1\n",
+						__func__);
+			continue;
+		}
+
+		/* do we need a NOP PHY device ? */
+		if (!gpio_is_valid(phy->reset_gpio) &&
+			!gpio_is_valid(phy->vcc_gpio))
+			continue;
+
+		/* create a NOP PHY device */
+		pdev = kzalloc(sizeof(*pdev), GFP_KERNEL);
+		if (!pdev)
+			return -ENOMEM;
+
+		pdev->id = phy->port;
+		pdev->name = nop_name;
+		pdev->dev.platform_data = phy->platform_data;
+
+		phy_id = kmalloc(len, GFP_KERNEL);
+		if (!phy_id)
+			return -ENOMEM;
+
+		scnprintf(phy_id, len, "nop_usb_xceiv.%d\n",
+					pdev->id);
+
+		if (platform_device_register(pdev)) {
+			pr_err("%s: Failed to register device %s\n",
+				__func__,  phy_id);
+			continue;
+		}
+
+		usb_bind_phy("ehci-omap.0", phy->port - 1, phy_id);
+
+		/* Do we need RESET regulator ? */
+		if (gpio_is_valid(phy->reset_gpio)) {
+
+			rail_name = kmalloc(13, GFP_KERNEL);
+			if (!rail_name)
+				return -ENOMEM;
+
+			scnprintf(rail_name, 13, "hsusb%d_reset", phy->port);
+
+			usbhs_add_regulator(rail_name, phy_id, "reset",
+						phy->reset_gpio, 1);
+		}
+
+		/* Do we need VCC regulator ? */
+		if (gpio_is_valid(phy->vcc_gpio)) {
+
+			rail_name = kmalloc(13, GFP_KERNEL);
+			if (!rail_name)
+				return -ENOMEM;
+
+			scnprintf(rail_name, 13, "hsusb%d_vcc", phy->port);
+
+			usbhs_add_regulator(rail_name, phy_id, "vcc",
+					phy->vcc_gpio, phy->vcc_polarity);
+		}
+
+		phy++;
+	}
+
+	return 0;
+}
diff --git a/arch/arm/mach-omap2/usb.h b/arch/arm/mach-omap2/usb.h
index 3319f5cf47a3aade4bdf79ba9605e3cdc183ee6f..e7261ebcf7b02ba83c4e4fe672d132636aeb841e 100644
--- a/arch/arm/mach-omap2/usb.h
+++ b/arch/arm/mach-omap2/usb.h
@@ -53,8 +53,17 @@
 #define USBPHY_OTGSESSEND_EN	(1 << 20)
 #define USBPHY_DATA_POLARITY	(1 << 23)
 
+struct usbhs_phy_data {
+	int port;		/* 1 indexed port number */
+	int reset_gpio;
+	int vcc_gpio;
+	bool vcc_polarity;	/* 1 active high, 0 active low */
+	void *platform_data;
+};
+
 extern void usb_musb_init(struct omap_musb_board_data *board_data);
 extern void usbhs_init(struct usbhs_omap_platform_data *pdata);
+extern int usbhs_init_phys(struct usbhs_phy_data *phy, int num_phys);
 
 extern void am35x_musb_reset(void);
 extern void am35x_musb_phy_power(u8 on);
diff --git a/include/linux/usb/nop-usb-xceiv.h b/include/linux/usb/nop-usb-xceiv.h
index 28884c7174112d7ede78d0283d9cba35802eddaa..148d35171aac622ab215bb6520f3dc3f0c0b431f 100644
--- a/include/linux/usb/nop-usb-xceiv.h
+++ b/include/linux/usb/nop-usb-xceiv.h
@@ -5,6 +5,11 @@
 
 struct nop_usb_xceiv_platform_data {
 	enum usb_phy_type type;
+	unsigned long clk_rate;
+
+	/* if set fails with -EPROBE_DEFER if can't get regulator */
+	unsigned int needs_vcc:1;
+	unsigned int needs_reset:1;
 };
 
 #if defined(CONFIG_NOP_USB_XCEIV) || (defined(CONFIG_NOP_USB_XCEIV_MODULE) && defined(MODULE))