Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 160
Star 36
Fork 7
cloud-kernel
cloud-kernel
提交 7a2207a0 编写于 作者: J Jean-Christophe PLAGNIOL-VILLARD
浏览文件
操作

at91: drop at572d940hf support 

no-one use it and it's nearly impossible get a board to work on it
and the Mainline implementation was never finished
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
上级 e57556e3
隐藏空白更改
内联 并排
Showing with 2 addition and 2350 deletion
arch/arm/configs/at572d940hfek_defconfig 已删除 100644 → 0
浏览文件 @ e57556e3
CONFIG_EXPERIMENTAL=y
CONFIG_LOCALVERSION="-AT572D940HF"
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
CONFIG_TASKSTATS=y
CONFIG_TASK_XACCT=y
CONFIG_TASK_IO_ACCOUNTING=y
CONFIG_AUDIT=y
CONFIG_CGROUPS=y
CONFIG_CGROUP_CPUACCT=y
CONFIG_CGROUP_SCHED=y
CONFIG_RT_GROUP_SCHED=y
CONFIG_SYSFS_DEPRECATED_V2=y
CONFIG_RELAY=y
CONFIG_BLK_DEV_INITRD=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_EXPERT=y
CONFIG_SLAB=y
CONFIG_PROFILING=y
CONFIG_OPROFILE=m
CONFIG_KPROBES=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
# CONFIG_BLK_DEV_BSG is not set
CONFIG_ARCH_AT91=y
CONFIG_ARCH_AT572D940HF=y
CONFIG_MACH_AT572D940HFEB=y
CONFIG_AT91_PROGRAMMABLE_CLOCKS=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_PREEMPT=y
CONFIG_CMDLINE="mem=48M console=ttyS0 initrd=0x21100000,3145728 root=/dev/ram0 rw ip=172.16.1.181"
CONFIG_KEXEC=y
CONFIG_FPE_NWFPE=y
CONFIG_FPE_NWFPE_XP=y
CONFIG_NET=y
CONFIG_PACKET=m
CONFIG_UNIX=y
CONFIG_INET=y
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_BEET is not set
# CONFIG_INET_LRO is not set
# CONFIG_INET_DIAG is not set
# CONFIG_IPV6 is not set
CONFIG_NET_PKTGEN=m
CONFIG_NET_TCPPROBE=m
CONFIG_CAN=m
CONFIG_CAN_RAW=m
CONFIG_CAN_BCM=m
CONFIG_CAN_VCAN=m
CONFIG_CAN_DEBUG_DEVICES=y
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_CONNECTOR=m
CONFIG_MTD=m
CONFIG_MTD_DEBUG=y
CONFIG_MTD_DEBUG_VERBOSE=1
CONFIG_MTD_CONCAT=m
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CHAR=m
CONFIG_MTD_BLOCK=m
CONFIG_MTD_BLOCK_RO=m
CONFIG_FTL=m
CONFIG_NFTL=m
CONFIG_NFTL_RW=y
CONFIG_INFTL=m
CONFIG_RFD_FTL=m
CONFIG_SSFDC=m
CONFIG_MTD_OOPS=m
CONFIG_MTD_CFI=m
CONFIG_MTD_JEDECPROBE=m
CONFIG_MTD_CFI_INTELEXT=m
CONFIG_MTD_CFI_AMDSTD=m
CONFIG_MTD_CFI_STAA=m
CONFIG_MTD_ROM=m
CONFIG_MTD_ABSENT=m
CONFIG_MTD_COMPLEX_MAPPINGS=y
CONFIG_MTD_PHYSMAP=m
CONFIG_MTD_PLATRAM=m
CONFIG_MTD_DATAFLASH=m
CONFIG_MTD_M25P80=m
CONFIG_MTD_SLRAM=m
CONFIG_MTD_PHRAM=m
CONFIG_MTD_MTDRAM=m
CONFIG_MTD_BLOCK2MTD=m
CONFIG_MTD_NAND=m
CONFIG_MTD_NAND_VERIFY_WRITE=y
CONFIG_MTD_NAND_DISKONCHIP=m
CONFIG_MTD_NAND_NANDSIM=m
CONFIG_MTD_NAND_PLATFORM=m
CONFIG_MTD_ALAUDA=m
CONFIG_MTD_UBI=m
CONFIG_MTD_UBI_GLUEBI=m
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=65536
CONFIG_ATMEL_TCLIB=y
CONFIG_ATMEL_SSC=m
CONFIG_SENSORS_TSL2550=m
CONFIG_DS1682=m
CONFIG_RAID_ATTRS=m
CONFIG_SCSI=m
CONFIG_SCSI_TGT=m
# CONFIG_SCSI_PROC_FS is not set
CONFIG_BLK_DEV_SD=m
CONFIG_BLK_DEV_SR=m
CONFIG_CHR_DEV_SG=m
CONFIG_CHR_DEV_SCH=m
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
CONFIG_SCSI_SCAN_ASYNC=y
CONFIG_SCSI_ISCSI_ATTRS=m
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
CONFIG_BONDING=m
CONFIG_MACVLAN=m
CONFIG_EQUALIZER=m
CONFIG_TUN=m
CONFIG_VETH=m
CONFIG_PHYLIB=y
CONFIG_MARVELL_PHY=m
CONFIG_DAVICOM_PHY=m
CONFIG_QSEMI_PHY=m
CONFIG_LXT_PHY=m
CONFIG_CICADA_PHY=m
CONFIG_VITESSE_PHY=m
CONFIG_SMSC_PHY=m
CONFIG_BROADCOM_PHY=m
CONFIG_ICPLUS_PHY=m
CONFIG_MDIO_BITBANG=m
CONFIG_NET_ETHERNET=y
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
CONFIG_USB_ZD1201=m
CONFIG_HOSTAP=m
CONFIG_HOSTAP_FIRMWARE=y
CONFIG_HOSTAP_FIRMWARE_NVRAM=y
CONFIG_USB_CATC=m
CONFIG_USB_KAWETH=m
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET=m
CONFIG_USB_NET_DM9601=m
CONFIG_USB_NET_GL620A=m
CONFIG_USB_NET_PLUSB=m
CONFIG_USB_NET_MCS7830=m
CONFIG_USB_NET_RNDIS_HOST=m
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_KC2190=y
# CONFIG_USB_NET_ZAURUS is not set
CONFIG_INPUT_MOUSEDEV=m
CONFIG_INPUT_EVDEV=m
CONFIG_INPUT_EVBUG=m
CONFIG_KEYBOARD_LKKBD=m
CONFIG_KEYBOARD_GPIO=m
CONFIG_KEYBOARD_NEWTON=m
CONFIG_KEYBOARD_STOWAWAY=m
CONFIG_KEYBOARD_SUNKBD=m
CONFIG_KEYBOARD_XTKBD=m
CONFIG_MOUSE_PS2=m
CONFIG_MOUSE_SERIAL=m
CONFIG_MOUSE_APPLETOUCH=m
CONFIG_MOUSE_VSXXXAA=m
CONFIG_MOUSE_GPIO=m
CONFIG_INPUT_MISC=y
CONFIG_INPUT_UINPUT=m
CONFIG_SERIO_SERPORT=m
CONFIG_SERIO_RAW=m
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_SERIAL_NONSTANDARD=y
CONFIG_N_HDLC=m
CONFIG_SPECIALIX=m
CONFIG_STALDRV=y
CONFIG_SERIAL_ATMEL=y
CONFIG_SERIAL_ATMEL_CONSOLE=y
CONFIG_IPMI_HANDLER=m
CONFIG_IPMI_DEVICE_INTERFACE=m
CONFIG_IPMI_SI=m
CONFIG_IPMI_WATCHDOG=m
CONFIG_IPMI_POWEROFF=m
CONFIG_HW_RANDOM=y
CONFIG_R3964=m
CONFIG_RAW_DRIVER=m
CONFIG_TCG_TPM=m
CONFIG_TCG_NSC=m
CONFIG_TCG_ATMEL=m
CONFIG_I2C=m
CONFIG_I2C_CHARDEV=m
CONFIG_SPI=y
CONFIG_SPI_ATMEL=y
CONFIG_SPI_BITBANG=m
CONFIG_SPI_SPIDEV=m
# CONFIG_HWMON is not set
# CONFIG_VGA_CONSOLE is not set
CONFIG_SOUND=m
CONFIG_SND=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
# CONFIG_SND_PCM_OSS_PLUGINS is not set
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_DYNAMIC_MINORS=y
# CONFIG_SND_VERBOSE_PROCFS is not set
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
CONFIG_SND_USB_AUDIO=m
CONFIG_SND_USB_CAIAQ=m
CONFIG_SND_USB_CAIAQ_INPUT=y
CONFIG_HID=m
CONFIG_HIDRAW=y
CONFIG_USB_HID=m
CONFIG_USB_HIDDEV=y
CONFIG_USB_KBD=m
CONFIG_USB_MOUSE=m
CONFIG_HID_A4TECH=m
CONFIG_HID_APPLE=m
CONFIG_HID_BELKIN=m
CONFIG_HID_CHERRY=m
CONFIG_HID_CHICONY=m
CONFIG_HID_CYPRESS=m
CONFIG_HID_EZKEY=m
CONFIG_HID_GYRATION=m
CONFIG_HID_LOGITECH=m
CONFIG_HID_MICROSOFT=m
CONFIG_HID_MONTEREY=m
CONFIG_HID_PANTHERLORD=m
CONFIG_HID_PETALYNX=m
CONFIG_HID_SAMSUNG=m
CONFIG_HID_SONY=m
CONFIG_HID_SUNPLUS=m
CONFIG_USB=y
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_DEVICE_CLASS is not set
CONFIG_USB_DYNAMIC_MINORS=y
CONFIG_USB_MON=y
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_STORAGE=m
CONFIG_USB_STORAGE_DATAFAB=m
CONFIG_USB_STORAGE_FREECOM=m
CONFIG_USB_STORAGE_ISD200=m
CONFIG_USB_STORAGE_USBAT=m
CONFIG_USB_STORAGE_SDDR09=m
CONFIG_USB_STORAGE_SDDR55=m
CONFIG_USB_STORAGE_JUMPSHOT=m
CONFIG_USB_STORAGE_ALAUDA=m
CONFIG_USB_STORAGE_KARMA=m
CONFIG_USB_LIBUSUAL=y
CONFIG_USB_SERIAL=m
CONFIG_USB_EZUSB=y
CONFIG_USB_SERIAL_GENERIC=y
CONFIG_USB_SERIAL_PL2303=m
CONFIG_USB_SERIAL_SPCP8X5=m
CONFIG_USB_SERIAL_DEBUG=m
CONFIG_USB_EMI62=m
CONFIG_USB_EMI26=m
CONFIG_USB_ADUTUX=m
CONFIG_USB_TEST=m
CONFIG_USB_GADGET=m
CONFIG_USB_GADGET_DEBUG_FILES=y
CONFIG_USB_GADGET_DEBUG_FS=y
CONFIG_USB_ZERO=m
CONFIG_USB_ETH=m
CONFIG_USB_GADGETFS=m
CONFIG_USB_FILE_STORAGE=m
CONFIG_USB_G_SERIAL=m
CONFIG_USB_MIDI_GADGET=m
CONFIG_MMC=y
CONFIG_SDIO_UART=m
CONFIG_MMC_AT91=m
CONFIG_MMC_SPI=m
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=m
CONFIG_LEDS_GPIO=m
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_TIMER=m
CONFIG_LEDS_TRIGGER_HEARTBEAT=m
CONFIG_RTC_CLASS=y
CONFIG_RTC_INTF_DEV_UIE_EMUL=y
CONFIG_RTC_DRV_DS1307=m
CONFIG_RTC_DRV_DS1305=y
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_EXT3_FS_SECURITY=y
CONFIG_JBD_DEBUG=y
CONFIG_REISERFS_FS=m
CONFIG_REISERFS_CHECK=y
CONFIG_REISERFS_PROC_INFO=y
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
CONFIG_REISERFS_FS_SECURITY=y
CONFIG_INOTIFY=y
CONFIG_FUSE_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=y
CONFIG_NTFS_FS=m
CONFIG_NTFS_RW=y
CONFIG_TMPFS=y
CONFIG_TMPFS_POSIX_ACL=y
CONFIG_JFFS2_FS=m
CONFIG_JFFS2_COMPRESSION_OPTIONS=y
CONFIG_JFFS2_LZO=y
CONFIG_JFFS2_CMODE_FAVOURLZO=y
CONFIG_CRAMFS=m
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_NFSD=m
CONFIG_NFSD_V3_ACL=y
CONFIG_NFSD_V4=y
CONFIG_CIFS=m
CONFIG_CIFS_WEAK_PW_HASH=y
CONFIG_PARTITION_ADVANCED=y
CONFIG_MAC_PARTITION=y
CONFIG_BSD_DISKLABEL=y
CONFIG_MINIX_SUBPARTITION=y
CONFIG_SOLARIS_X86_PARTITION=y
CONFIG_UNIXWARE_DISKLABEL=y
CONFIG_LDM_PARTITION=y
CONFIG_LDM_DEBUG=y
CONFIG_SGI_PARTITION=y
CONFIG_SUN_PARTITION=y
CONFIG_NLS_DEFAULT="cp437"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_UTF8=m
CONFIG_DLM=m
CONFIG_PRINTK_TIME=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_UNUSED_SYMBOLS=y
CONFIG_DEBUG_FS=y
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_CRYPTO=y
CONFIG_CRYPTO_GF128MUL=m
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_ANSI_CPRNG is not set
# CONFIG_CRYPTO_HW is not set
CONFIG_CRC_CCITT=m
CONFIG_CRC16=m
arch/arm/mach-at91/Kconfig
浏览文件 @ 7a2207a0
......@@ -82,11 +82,6 @@ config ARCH_AT91CAP9
select HAVE_FB_ATMEL
select HAVE_NET_MACB
config ARCH_AT572D940HF
bool "AT572D940HF"
select CPU_ARM926T
select GENERIC_CLOCKEVENTS
config ARCH_AT91X40
bool "AT91x40"
select ARCH_USES_GETTIMEOFFSET
......@@ -431,22 +426,6 @@ endif
# ----------------------------------------------------------
if ARCH_AT572D940HF
comment "AT572D940HF Board Type"
config MACH_AT572D940HFEB
bool "AT572D940HF-EK"
depends on ARCH_AT572D940HF
select HAVE_AT91_DATAFLASH_CARD
help
Select this if you are using Atmel's AT572D940HF-EK evaluation kit.
<http://www.atmel.com/products/diopsis/default.asp>
endif
# ----------------------------------------------------------
if ARCH_AT91X40
comment "AT91X40 Board Type"
......
arch/arm/mach-at91/Makefile
浏览文件 @ 7a2207a0
......@@ -19,7 +19,6 @@ obj-$(CONFIG_ARCH_AT91SAM9RL) += at91sam9rl.o at91sam926x_time.o at91sam9rl_devi
obj-$(CONFIG_ARCH_AT91SAM9G20) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o sam9_smc.o at91sam9_alt_reset.o
obj-$(CONFIG_ARCH_AT91SAM9G45) += at91sam9g45.o at91sam926x_time.o at91sam9g45_devices.o sam9_smc.o
obj-$(CONFIG_ARCH_AT91CAP9) += at91cap9.o at91sam926x_time.o at91cap9_devices.o sam9_smc.o
obj-$(CONFIG_ARCH_AT572D940HF) += at572d940hf.o at91sam926x_time.o at572d940hf_devices.o sam9_smc.o
obj-$(CONFIG_ARCH_AT91X40) += at91x40.o at91x40_time.o
# AT91RM9200 board-specific support
......@@ -78,9 +77,6 @@ obj-$(CONFIG_MACH_AT91SAM9M10G45EK) += board-sam9m10g45ek.o
# AT91CAP9 board-specific support
obj-$(CONFIG_MACH_AT91CAP9ADK) += board-cap9adk.o
# AT572D940HF board-specific support
obj-$(CONFIG_MACH_AT572D940HFEB) += board-at572d940hf_ek.o
# AT91X40 board-specific support
obj-$(CONFIG_MACH_AT91EB01) += board-eb01.o
......
arch/arm/mach-at91/at572d940hf.c 已删除 100644 → 0
浏览文件 @ e57556e3
/*
* arch/arm/mach-at91/at572d940hf.c
*
* Antonio R. Costa <costa.antonior@gmail.com>
* Copyright (C) 2008 Atmel
*
* Copyright (C) 2005 SAN People
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
*/
#include <linux/module.h>
#include <asm/mach/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <mach/at572d940hf.h>
#include <mach/at91_pmc.h>
#include <mach/at91_rstc.h>
#include "generic.h"
#include "clock.h"
static struct map_desc at572d940hf_io_desc[] __initdata = {
{
.virtual = AT91_VA_BASE_SYS,
.pfn = __phys_to_pfn(AT91_BASE_SYS),
.length = SZ_16K,
.type = MT_DEVICE,
}, {
.virtual = AT91_IO_VIRT_BASE - AT572D940HF_SRAM_SIZE,
.pfn = __phys_to_pfn(AT572D940HF_SRAM_BASE),
.length = AT572D940HF_SRAM_SIZE,
.type = MT_DEVICE,
},
};
/* --------------------------------------------------------------------
* Clocks
* -------------------------------------------------------------------- */
/*
* The peripheral clocks.
*/
static struct clk pioA_clk = {
.name = "pioA_clk",
.pmc_mask = 1 << AT572D940HF_ID_PIOA,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk pioB_clk = {
.name = "pioB_clk",
.pmc_mask = 1 << AT572D940HF_ID_PIOB,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk pioC_clk = {
.name = "pioC_clk",
.pmc_mask = 1 << AT572D940HF_ID_PIOC,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk macb_clk = {
.name = "macb_clk",
.pmc_mask = 1 << AT572D940HF_ID_EMAC,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk usart0_clk = {
.name = "usart0_clk",
.pmc_mask = 1 << AT572D940HF_ID_US0,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk usart1_clk = {
.name = "usart1_clk",
.pmc_mask = 1 << AT572D940HF_ID_US1,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk usart2_clk = {
.name = "usart2_clk",
.pmc_mask = 1 << AT572D940HF_ID_US2,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk mmc_clk = {
.name = "mci_clk",
.pmc_mask = 1 << AT572D940HF_ID_MCI,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk udc_clk = {
.name = "udc_clk",
.pmc_mask = 1 << AT572D940HF_ID_UDP,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk twi0_clk = {
.name = "twi0_clk",
.pmc_mask = 1 << AT572D940HF_ID_TWI0,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk spi0_clk = {
.name = "spi0_clk",
.pmc_mask = 1 << AT572D940HF_ID_SPI0,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk spi1_clk = {
.name = "spi1_clk",
.pmc_mask = 1 << AT572D940HF_ID_SPI1,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk ssc0_clk = {
.name = "ssc0_clk",
.pmc_mask = 1 << AT572D940HF_ID_SSC0,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk ssc1_clk = {
.name = "ssc1_clk",
.pmc_mask = 1 << AT572D940HF_ID_SSC1,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk ssc2_clk = {
.name = "ssc2_clk",
.pmc_mask = 1 << AT572D940HF_ID_SSC2,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk tc0_clk = {
.name = "tc0_clk",
.pmc_mask = 1 << AT572D940HF_ID_TC0,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk tc1_clk = {
.name = "tc1_clk",
.pmc_mask = 1 << AT572D940HF_ID_TC1,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk tc2_clk = {
.name = "tc2_clk",
.pmc_mask = 1 << AT572D940HF_ID_TC2,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk ohci_clk = {
.name = "ohci_clk",
.pmc_mask = 1 << AT572D940HF_ID_UHP,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk ssc3_clk = {
.name = "ssc3_clk",
.pmc_mask = 1 << AT572D940HF_ID_SSC3,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk twi1_clk = {
.name = "twi1_clk",
.pmc_mask = 1 << AT572D940HF_ID_TWI1,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk can0_clk = {
.name = "can0_clk",
.pmc_mask = 1 << AT572D940HF_ID_CAN0,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk can1_clk = {
.name = "can1_clk",
.pmc_mask = 1 << AT572D940HF_ID_CAN1,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk mAgicV_clk = {
.name = "mAgicV_clk",
.pmc_mask = 1 << AT572D940HF_ID_MSIRQ0,
.type = CLK_TYPE_PERIPHERAL,
};
static struct clk *periph_clocks[] __initdata = {
&pioA_clk,
&pioB_clk,
&pioC_clk,
&macb_clk,
&usart0_clk,
&usart1_clk,
&usart2_clk,
&mmc_clk,
&udc_clk,
&twi0_clk,
&spi0_clk,
&spi1_clk,
&ssc0_clk,
&ssc1_clk,
&ssc2_clk,
&tc0_clk,
&tc1_clk,
&tc2_clk,
&ohci_clk,
&ssc3_clk,
&twi1_clk,
&can0_clk,
&can1_clk,
&mAgicV_clk,
/* irq0 .. irq2 */
};
static struct clk_lookup periph_clocks_lookups[] = {
CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.0", &tc1_clk),
CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk),
};
static struct clk_lookup usart_clocks_lookups[] = {
CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
};
/*
* The five programmable clocks.
* You must configure pin multiplexing to bring these signals out.
*/
static struct clk pck0 = {
.name = "pck0",
.pmc_mask = AT91_PMC_PCK0,
.type = CLK_TYPE_PROGRAMMABLE,
.id = 0,
};
static struct clk pck1 = {
.name = "pck1",
.pmc_mask = AT91_PMC_PCK1,
.type = CLK_TYPE_PROGRAMMABLE,
.id = 1,
};
static struct clk pck2 = {
.name = "pck2",
.pmc_mask = AT91_PMC_PCK2,
.type = CLK_TYPE_PROGRAMMABLE,
.id = 2,
};
static struct clk pck3 = {
.name = "pck3",
.pmc_mask = AT91_PMC_PCK3,
.type = CLK_TYPE_PROGRAMMABLE,
.id = 3,
};
static struct clk mAgicV_mem_clk = {
.name = "mAgicV_mem_clk",
.pmc_mask = AT91_PMC_PCK4,
.type = CLK_TYPE_PROGRAMMABLE,
.id = 4,
};
/* HClocks */
static struct clk hck0 = {
.name = "hck0",
.pmc_mask = AT91_PMC_HCK0,
.type = CLK_TYPE_SYSTEM,
.id = 0,
};
static struct clk hck1 = {
.name = "hck1",
.pmc_mask = AT91_PMC_HCK1,
.type = CLK_TYPE_SYSTEM,
.id = 1,
};
static void __init at572d940hf_register_clocks(void)
{
int i;
for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
clk_register(periph_clocks[i]);
clkdev_add_table(periph_clocks_lookups,
ARRAY_SIZE(periph_clocks_lookups));
clkdev_add_table(usart_clocks_lookups,
ARRAY_SIZE(usart_clocks_lookups));
clk_register(&pck0);
clk_register(&pck1);
clk_register(&pck2);
clk_register(&pck3);
clk_register(&mAgicV_mem_clk);
clk_register(&hck0);
clk_register(&hck1);
}
static struct clk_lookup console_clock_lookup;
void __init at572d940hf_set_console_clock(int id)
{
if (id >= ARRAY_SIZE(usart_clocks_lookups))
return;
console_clock_lookup.con_id = "usart";
console_clock_lookup.clk = usart_clocks_lookups[id].clk;
clkdev_add(&console_clock_lookup);
}
/* --------------------------------------------------------------------
* GPIO
* -------------------------------------------------------------------- */
static struct at91_gpio_bank at572d940hf_gpio[] = {
{
.id = AT572D940HF_ID_PIOA,
.offset = AT91_PIOA,
.clock = &pioA_clk,
}, {
.id = AT572D940HF_ID_PIOB,
.offset = AT91_PIOB,
.clock = &pioB_clk,
}, {
.id = AT572D940HF_ID_PIOC,
.offset = AT91_PIOC,
.clock = &pioC_clk,
}
};
static void at572d940hf_reset(void)
{
at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST);
}
/* --------------------------------------------------------------------
* AT572D940HF processor initialization
* -------------------------------------------------------------------- */
void __init at572d940hf_map_io(void)
{
/* Map peripherals */
iotable_init(at572d940hf_io_desc, ARRAY_SIZE(at572d940hf_io_desc));
}
void __init at572d940hf_initialize(unsigned long main_clock)
{
at91_arch_reset = at572d940hf_reset;
at91_extern_irq = (1 << AT572D940HF_ID_IRQ0) | (1 << AT572D940HF_ID_IRQ1)
| (1 << AT572D940HF_ID_IRQ2);
/* Init clock subsystem */
at91_clock_init(main_clock);
/* Register the processor-specific clocks */
at572d940hf_register_clocks();
/* Register GPIO subsystem */
at91_gpio_init(at572d940hf_gpio, 3);
}
/* --------------------------------------------------------------------
* Interrupt initialization
* -------------------------------------------------------------------- */
/*
* The default interrupt priority levels (0 = lowest, 7 = highest).
*/
static unsigned int at572d940hf_default_irq_priority[NR_AIC_IRQS] __initdata = {
7, /* Advanced Interrupt Controller */
7, /* System Peripherals */
0, /* Parallel IO Controller A */
0, /* Parallel IO Controller B */
0, /* Parallel IO Controller C */
3, /* Ethernet */
6, /* USART 0 */
6, /* USART 1 */
6, /* USART 2 */
0, /* Multimedia Card Interface */
4, /* USB Device Port */
0, /* Two-Wire Interface 0 */
6, /* Serial Peripheral Interface 0 */
6, /* Serial Peripheral Interface 1 */
5, /* Serial Synchronous Controller 0 */
5, /* Serial Synchronous Controller 1 */
5, /* Serial Synchronous Controller 2 */
0, /* Timer Counter 0 */
0, /* Timer Counter 1 */
0, /* Timer Counter 2 */
3, /* USB Host port */
3, /* Serial Synchronous Controller 3 */
0, /* Two-Wire Interface 1 */
0, /* CAN Controller 0 */
0, /* CAN Controller 1 */
0, /* mAgicV HALT line */
0, /* mAgicV SIRQ0 line */
0, /* mAgicV exception line */
0, /* mAgicV end of DMA line */
0, /* Advanced Interrupt Controller */
0, /* Advanced Interrupt Controller */
0, /* Advanced Interrupt Controller */
};
void __init at572d940hf_init_interrupts(unsigned int priority[NR_AIC_IRQS])
{
if (!priority)
priority = at572d940hf_default_irq_priority;
/* Initialize the AIC interrupt controller */
at91_aic_init(priority);
/* Enable GPIO interrupts */
at91_gpio_irq_setup();
}
arch/arm/mach-at91/at572d940hf_devices.c 已删除 100644 → 0
浏览文件 @ e57556e3
/*
* arch/arm/mach-at91/at572d940hf_devices.c
*
* Copyright (C) 2008 Atmel Antonio R. Costa <costa.antonior@gmail.com>
* Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
* Copyright (C) 2005 David Brownell
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
*/
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <linux/dma-mapping.h>
#include <linux/platform_device.h>
#include <mach/board.h>
#include <mach/gpio.h>
#include <mach/at572d940hf.h>
#include <mach/at572d940hf_matrix.h>
#include <mach/at91sam9_smc.h>
#include "generic.h"
#include "sam9_smc.h"
/* --------------------------------------------------------------------
* USB Host
* -------------------------------------------------------------------- */
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
static u64 ohci_dmamask = DMA_BIT_MASK(32);
static struct at91_usbh_data usbh_data;
static struct resource usbh_resources[] = {
[0] = {
.start = AT572D940HF_UHP_BASE,
.end = AT572D940HF_UHP_BASE + SZ_1M - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AT572D940HF_ID_UHP,
.end = AT572D940HF_ID_UHP,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device at572d940hf_usbh_device = {
.name = "at91_ohci",
.id = -1,
.dev = {
.dma_mask = &ohci_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
.platform_data = &usbh_data,
},
.resource = usbh_resources,
.num_resources = ARRAY_SIZE(usbh_resources),
};
void __init at91_add_device_usbh(struct at91_usbh_data *data)
{
if (!data)
return;
usbh_data = *data;
platform_device_register(&at572d940hf_usbh_device);
}
#else
void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
#endif
/* --------------------------------------------------------------------
* USB Device (Gadget)
* -------------------------------------------------------------------- */
#ifdef CONFIG_USB_GADGET_AT91
static struct at91_udc_data udc_data;
static struct resource udc_resources[] = {
[0] = {
.start = AT572D940HF_BASE_UDP,
.end = AT572D940HF_BASE_UDP + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AT572D940HF_ID_UDP,
.end = AT572D940HF_ID_UDP,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device at572d940hf_udc_device = {
.name = "at91_udc",
.id = -1,
.dev = {
.platform_data = &udc_data,
},
.resource = udc_resources,
.num_resources = ARRAY_SIZE(udc_resources),
};
void __init at91_add_device_udc(struct at91_udc_data *data)
{
if (!data)
return;
if (data->vbus_pin) {
at91_set_gpio_input(data->vbus_pin, 0);
at91_set_deglitch(data->vbus_pin, 1);
}
/* Pullup pin is handled internally */
udc_data = *data;
platform_device_register(&at572d940hf_udc_device);
}
#else
void __init at91_add_device_udc(struct at91_udc_data *data) {}
#endif
/* --------------------------------------------------------------------
* Ethernet
* -------------------------------------------------------------------- */
#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
static u64 eth_dmamask = DMA_BIT_MASK(32);
static struct at91_eth_data eth_data;
static struct resource eth_resources[] = {
[0] = {
.start = AT572D940HF_BASE_EMAC,
.end = AT572D940HF_BASE_EMAC + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AT572D940HF_ID_EMAC,
.end = AT572D940HF_ID_EMAC,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device at572d940hf_eth_device = {
.name = "macb",
.id = -1,
.dev = {
.dma_mask = &eth_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
.platform_data = &eth_data,
},
.resource = eth_resources,
.num_resources = ARRAY_SIZE(eth_resources),
};
void __init at91_add_device_eth(struct at91_eth_data *data)
{
if (!data)
return;
if (data->phy_irq_pin) {
at91_set_gpio_input(data->phy_irq_pin, 0);
at91_set_deglitch(data->phy_irq_pin, 1);
}
/* Only RMII is supported */
data->is_rmii = 1;
/* Pins used for RMII */
at91_set_A_periph(AT91_PIN_PA16, 0); /* ETXCK_EREFCK */
at91_set_A_periph(AT91_PIN_PA17, 0); /* ERXDV */
at91_set_A_periph(AT91_PIN_PA18, 0); /* ERX0 */
at91_set_A_periph(AT91_PIN_PA19, 0); /* ERX1 */
at91_set_A_periph(AT91_PIN_PA20, 0); /* ERXER */
at91_set_A_periph(AT91_PIN_PA23, 0); /* ETXEN */
at91_set_A_periph(AT91_PIN_PA21, 0); /* ETX0 */
at91_set_A_periph(AT91_PIN_PA22, 0); /* ETX1 */
at91_set_A_periph(AT91_PIN_PA13, 0); /* EMDIO */
at91_set_A_periph(AT91_PIN_PA14, 0); /* EMDC */
eth_data = *data;
platform_device_register(&at572d940hf_eth_device);
}
#else
void __init at91_add_device_eth(struct at91_eth_data *data) {}
#endif
/* --------------------------------------------------------------------
* MMC / SD
* -------------------------------------------------------------------- */
#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE)
static u64 mmc_dmamask = DMA_BIT_MASK(32);
static struct at91_mmc_data mmc_data;
static struct resource mmc_resources[] = {
[0] = {
.start = AT572D940HF_BASE_MCI,
.end = AT572D940HF_BASE_MCI + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AT572D940HF_ID_MCI,
.end = AT572D940HF_ID_MCI,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device at572d940hf_mmc_device = {
.name = "at91_mci",
.id = -1,
.dev = {
.dma_mask = &mmc_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
.platform_data = &mmc_data,
},
.resource = mmc_resources,
.num_resources = ARRAY_SIZE(mmc_resources),
};
void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
{
if (!data)
return;
/* input/irq */
if (data->det_pin) {
at91_set_gpio_input(data->det_pin, 1);
at91_set_deglitch(data->det_pin, 1);
}
if (data->wp_pin)
at91_set_gpio_input(data->wp_pin, 1);
if (data->vcc_pin)
at91_set_gpio_output(data->vcc_pin, 0);
/* CLK */
at91_set_A_periph(AT91_PIN_PC22, 0);
/* CMD */
at91_set_A_periph(AT91_PIN_PC23, 1);
/* DAT0, maybe DAT1..DAT3 */
at91_set_A_periph(AT91_PIN_PC24, 1);
if (data->wire4) {
at91_set_A_periph(AT91_PIN_PC25, 1);
at91_set_A_periph(AT91_PIN_PC26, 1);
at91_set_A_periph(AT91_PIN_PC27, 1);
}
mmc_data = *data;
platform_device_register(&at572d940hf_mmc_device);
}
#else
void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
#endif
/* --------------------------------------------------------------------
* NAND / SmartMedia
* -------------------------------------------------------------------- */
#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
static struct atmel_nand_data nand_data;
#define NAND_BASE AT91_CHIPSELECT_3
static struct resource nand_resources[] = {
{
.start = NAND_BASE,
.end = NAND_BASE + SZ_256M - 1,
.flags = IORESOURCE_MEM,
}
};
static struct platform_device at572d940hf_nand_device = {
.name = "atmel_nand",
.id = -1,
.dev = {
.platform_data = &nand_data,
},
.resource = nand_resources,
.num_resources = ARRAY_SIZE(nand_resources),
};
void __init at91_add_device_nand(struct atmel_nand_data *data)
{
unsigned long csa;
if (!data)
return;
csa = at91_sys_read(AT91_MATRIX_EBICSA);
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
/* enable pin */
if (data->enable_pin)
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
if (data->rdy_pin)
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
if (data->det_pin)
at91_set_gpio_input(data->det_pin, 1);
at91_set_A_periph(AT91_PIN_PB28, 0); /* A[22] */
at91_set_B_periph(AT91_PIN_PA28, 0); /* NANDOE */
at91_set_B_periph(AT91_PIN_PA29, 0); /* NANDWE */
nand_data = *data;
platform_device_register(&at572d940hf_nand_device);
}
#else
void __init at91_add_device_nand(struct atmel_nand_data *data) {}
#endif
/* --------------------------------------------------------------------
* TWI (i2c)
* -------------------------------------------------------------------- */
/*
* Prefer the GPIO code since the TWI controller isn't robust
* (gets overruns and underruns under load) and can only issue
* repeated STARTs in one scenario (the driver doesn't yet handle them).
*/
#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
static struct i2c_gpio_platform_data pdata = {
.sda_pin = AT91_PIN_PC7,
.sda_is_open_drain = 1,
.scl_pin = AT91_PIN_PC8,
.scl_is_open_drain = 1,
.udelay = 2, /* ~100 kHz */
};
static struct platform_device at572d940hf_twi_device {
.name = "i2c-gpio",
.id = -1,
.dev.platform_data = &pdata,
};
void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
{
at91_set_GPIO_periph(AT91_PIN_PC7, 1); /* TWD (SDA) */
at91_set_multi_drive(AT91_PIN_PC7, 1);
at91_set_GPIO_periph(AT91_PIN_PA8, 1); /* TWCK (SCL) */
at91_set_multi_drive(AT91_PIN_PC8, 1);
i2c_register_board_info(0, devices, nr_devices);
platform_device_register(&at572d940hf_twi_device);
}
#elif defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
static struct resource twi0_resources[] = {
[0] = {
.start = AT572D940HF_BASE_TWI0,
.end = AT572D940HF_BASE_TWI0 + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AT572D940HF_ID_TWI0,
.end = AT572D940HF_ID_TWI0,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device at572d940hf_twi0_device = {
.name = "at91_i2c",
.id = 0,
.resource = twi0_resources,
.num_resources = ARRAY_SIZE(twi0_resources),
};
static struct resource twi1_resources[] = {
[0] = {
.start = AT572D940HF_BASE_TWI1,
.end = AT572D940HF_BASE_TWI1 + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AT572D940HF_ID_TWI1,
.end = AT572D940HF_ID_TWI1,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device at572d940hf_twi1_device = {
.name = "at91_i2c",
.id = 1,
.resource = twi1_resources,
.num_resources = ARRAY_SIZE(twi1_resources),
};
void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
{
/* pins used for TWI0 interface */
at91_set_A_periph(AT91_PIN_PC7, 0); /* TWD */
at91_set_multi_drive(AT91_PIN_PC7, 1);
at91_set_A_periph(AT91_PIN_PC8, 0); /* TWCK */
at91_set_multi_drive(AT91_PIN_PC8, 1);
/* pins used for TWI1 interface */
at91_set_A_periph(AT91_PIN_PC20, 0); /* TWD */
at91_set_multi_drive(AT91_PIN_PC20, 1);
at91_set_A_periph(AT91_PIN_PC21, 0); /* TWCK */
at91_set_multi_drive(AT91_PIN_PC21, 1);
i2c_register_board_info(0, devices, nr_devices);
platform_device_register(&at572d940hf_twi0_device);
platform_device_register(&at572d940hf_twi1_device);
}
#else
void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices) {}
#endif
/* --------------------------------------------------------------------
* SPI
* -------------------------------------------------------------------- */
#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
static u64 spi_dmamask = DMA_BIT_MASK(32);
static struct resource spi0_resources[] = {
[0] = {
.start = AT572D940HF_BASE_SPI0,
.end = AT572D940HF_BASE_SPI0 + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AT572D940HF_ID_SPI0,
.end = AT572D940HF_ID_SPI0,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device at572d940hf_spi0_device = {
.name = "atmel_spi",
.id = 0,
.dev = {
.dma_mask = &spi_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
},
.resource = spi0_resources,
.num_resources = ARRAY_SIZE(spi0_resources),
};
static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PA5, AT91_PIN_PA6 };
static struct resource spi1_resources[] = {
[0] = {
.start = AT572D940HF_BASE_SPI1,
.end = AT572D940HF_BASE_SPI1 + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AT572D940HF_ID_SPI1,
.end = AT572D940HF_ID_SPI1,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device at572d940hf_spi1_device = {
.name = "atmel_spi",
.id = 1,
.dev = {
.dma_mask = &spi_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
},
.resource = spi1_resources,
.num_resources = ARRAY_SIZE(spi1_resources),
};
static const unsigned spi1_standard_cs[4] = { AT91_PIN_PC3, AT91_PIN_PC4, AT91_PIN_PC5, AT91_PIN_PC6 };
void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
{
int i;
unsigned long cs_pin;
short enable_spi0 = 0;
short enable_spi1 = 0;
/* Choose SPI chip-selects */
for (i = 0; i < nr_devices; i++) {
if (devices[i].controller_data)
cs_pin = (unsigned long) devices[i].controller_data;
else if (devices[i].bus_num == 0)
cs_pin = spi0_standard_cs[devices[i].chip_select];
else
cs_pin = spi1_standard_cs[devices[i].chip_select];
if (devices[i].bus_num == 0)
enable_spi0 = 1;
else
enable_spi1 = 1;
/* enable chip-select pin */
at91_set_gpio_output(cs_pin, 1);
/* pass chip-select pin to driver */
devices[i].controller_data = (void *) cs_pin;
}
spi_register_board_info(devices, nr_devices);
/* Configure SPI bus(es) */
if (enable_spi0) {
at91_set_A_periph(AT91_PIN_PA0, 0); /* SPI0_MISO */
at91_set_A_periph(AT91_PIN_PA1, 0); /* SPI0_MOSI */
at91_set_A_periph(AT91_PIN_PA2, 0); /* SPI0_SPCK */
platform_device_register(&at572d940hf_spi0_device);
}
if (enable_spi1) {
at91_set_A_periph(AT91_PIN_PC0, 0); /* SPI1_MISO */
at91_set_A_periph(AT91_PIN_PC1, 0); /* SPI1_MOSI */
at91_set_A_periph(AT91_PIN_PC2, 0); /* SPI1_SPCK */
platform_device_register(&at572d940hf_spi1_device);
}
}
#else
void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
#endif
/* --------------------------------------------------------------------
* Timer/Counter blocks
* -------------------------------------------------------------------- */
#ifdef CONFIG_ATMEL_TCLIB
static struct resource tcb_resources[] = {
[0] = {
.start = AT572D940HF_BASE_TCB,
.end = AT572D940HF_BASE_TCB + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AT572D940HF_ID_TC0,
.end = AT572D940HF_ID_TC0,
.flags = IORESOURCE_IRQ,
},
[2] = {
.start = AT572D940HF_ID_TC1,
.end = AT572D940HF_ID_TC1,
.flags = IORESOURCE_IRQ,
},
[3] = {
.start = AT572D940HF_ID_TC2,
.end = AT572D940HF_ID_TC2,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device at572d940hf_tcb_device = {
.name = "atmel_tcb",
.id = 0,
.resource = tcb_resources,
.num_resources = ARRAY_SIZE(tcb_resources),
};
static void __init at91_add_device_tc(void)
{
platform_device_register(&at572d940hf_tcb_device);
}
#else
static void __init at91_add_device_tc(void) { }
#endif
/* --------------------------------------------------------------------
* RTT
* -------------------------------------------------------------------- */
static struct resource rtt_resources[] = {
{
.start = AT91_BASE_SYS + AT91_RTT,
.end = AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
.flags = IORESOURCE_MEM,
}
};
static struct platform_device at572d940hf_rtt_device = {
.name = "at91_rtt",
.id = 0,
.resource = rtt_resources,
.num_resources = ARRAY_SIZE(rtt_resources),
};
static void __init at91_add_device_rtt(void)
{
platform_device_register(&at572d940hf_rtt_device);
}
/* --------------------------------------------------------------------
* Watchdog
* -------------------------------------------------------------------- */
#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
static struct platform_device at572d940hf_wdt_device = {
.name = "at91_wdt",
.id = -1,
.num_resources = 0,
};
static void __init at91_add_device_watchdog(void)
{
platform_device_register(&at572d940hf_wdt_device);
}
#else
static void __init at91_add_device_watchdog(void) {}
#endif
/* --------------------------------------------------------------------
* UART
* -------------------------------------------------------------------- */
#if defined(CONFIG_SERIAL_ATMEL)
static struct resource dbgu_resources[] = {
[0] = {
.start = AT91_VA_BASE_SYS + AT91_DBGU,
.end = AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AT91_ID_SYS,
.end = AT91_ID_SYS,
.flags = IORESOURCE_IRQ,
},
};
static struct atmel_uart_data dbgu_data = {
.use_dma_tx = 0,
.use_dma_rx = 0, /* DBGU not capable of receive DMA */
.regs = (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU),
};
static u64 dbgu_dmamask = DMA_BIT_MASK(32);
static struct platform_device at572d940hf_dbgu_device = {
.name = "atmel_usart",
.id = 0,
.dev = {
.dma_mask = &dbgu_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
.platform_data = &dbgu_data,
},
.resource = dbgu_resources,
.num_resources = ARRAY_SIZE(dbgu_resources),
};
static inline void configure_dbgu_pins(void)
{
at91_set_A_periph(AT91_PIN_PC31, 1); /* DTXD */
at91_set_A_periph(AT91_PIN_PC30, 0); /* DRXD */
}
static struct resource uart0_resources[] = {
[0] = {
.start = AT572D940HF_BASE_US0,
.end = AT572D940HF_BASE_US0 + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AT572D940HF_ID_US0,
.end = AT572D940HF_ID_US0,
.flags = IORESOURCE_IRQ,
},
};
static struct atmel_uart_data uart0_data = {
.use_dma_tx = 1,
.use_dma_rx = 1,
};
static u64 uart0_dmamask = DMA_BIT_MASK(32);
static struct platform_device at572d940hf_uart0_device = {
.name = "atmel_usart",
.id = 1,
.dev = {
.dma_mask = &uart0_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
.platform_data = &uart0_data,
},
.resource = uart0_resources,
.num_resources = ARRAY_SIZE(uart0_resources),
};
static inline void configure_usart0_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PA8, 1); /* TXD0 */
at91_set_A_periph(AT91_PIN_PA7, 0); /* RXD0 */
if (pins & ATMEL_UART_RTS)
at91_set_A_periph(AT91_PIN_PA10, 0); /* RTS0 */
if (pins & ATMEL_UART_CTS)
at91_set_A_periph(AT91_PIN_PA9, 0); /* CTS0 */
}
static struct resource uart1_resources[] = {
[0] = {
.start = AT572D940HF_BASE_US1,
.end = AT572D940HF_BASE_US1 + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AT572D940HF_ID_US1,
.end = AT572D940HF_ID_US1,
.flags = IORESOURCE_IRQ,
},
};
static struct atmel_uart_data uart1_data = {
.use_dma_tx = 1,
.use_dma_rx = 1,
};
static u64 uart1_dmamask = DMA_BIT_MASK(32);
static struct platform_device at572d940hf_uart1_device = {
.name = "atmel_usart",
.id = 2,
.dev = {
.dma_mask = &uart1_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
.platform_data = &uart1_data,
},
.resource = uart1_resources,
.num_resources = ARRAY_SIZE(uart1_resources),
};
static inline void configure_usart1_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PC10, 1); /* TXD1 */
at91_set_A_periph(AT91_PIN_PC9 , 0); /* RXD1 */
if (pins & ATMEL_UART_RTS)
at91_set_A_periph(AT91_PIN_PC12, 0); /* RTS1 */
if (pins & ATMEL_UART_CTS)
at91_set_A_periph(AT91_PIN_PC11, 0); /* CTS1 */
}
static struct resource uart2_resources[] = {
[0] = {
.start = AT572D940HF_BASE_US2,
.end = AT572D940HF_BASE_US2 + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AT572D940HF_ID_US2,
.end = AT572D940HF_ID_US2,
.flags = IORESOURCE_IRQ,
},
};
static struct atmel_uart_data uart2_data = {
.use_dma_tx = 1,
.use_dma_rx = 1,
};
static u64 uart2_dmamask = DMA_BIT_MASK(32);
static struct platform_device at572d940hf_uart2_device = {
.name = "atmel_usart",
.id = 3,
.dev = {
.dma_mask = &uart2_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
.platform_data = &uart2_data,
},
.resource = uart2_resources,
.num_resources = ARRAY_SIZE(uart2_resources),
};
static inline void configure_usart2_pins(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PC15, 1); /* TXD2 */
at91_set_A_periph(AT91_PIN_PC14, 0); /* RXD2 */
if (pins & ATMEL_UART_RTS)
at91_set_A_periph(AT91_PIN_PC17, 0); /* RTS2 */
if (pins & ATMEL_UART_CTS)
at91_set_A_periph(AT91_PIN_PC16, 0); /* CTS2 */
}
static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
struct platform_device *atmel_default_console_device; /* the serial console device */
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
{
struct platform_device *pdev;
struct atmel_uart_data *pdata;
switch (id) {
case 0: /* DBGU */
pdev = &at572d940hf_dbgu_device;
configure_dbgu_pins();
break;
case AT572D940HF_ID_US0:
pdev = &at572d940hf_uart0_device;
configure_usart0_pins(pins);
break;
case AT572D940HF_ID_US1:
pdev = &at572d940hf_uart1_device;
configure_usart1_pins(pins);
break;
case AT572D940HF_ID_US2:
pdev = &at572d940hf_uart2_device;
configure_usart2_pins(pins);
break;
default:
return;
}
pdata = pdev->dev.platform_data;
pdata->num = portnr; /* update to mapped ID */
if (portnr < ATMEL_MAX_UART)
at91_uarts[portnr] = pdev;
}
void __init at91_set_serial_console(unsigned portnr)
{
if (portnr < ATMEL_MAX_UART) {
atmel_default_console_device = at91_uarts[portnr];
at572d940hf_set_console_clock(portnr);
}
}
void __init at91_add_device_serial(void)
{
int i;
for (i = 0; i < ATMEL_MAX_UART; i++) {
if (at91_uarts[i])
platform_device_register(at91_uarts[i]);
}
if (!atmel_default_console_device)
printk(KERN_INFO "AT91: No default serial console defined.\n");
}
#else
void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
void __init at91_set_serial_console(unsigned portnr) {}
void __init at91_add_device_serial(void) {}
#endif
/* --------------------------------------------------------------------
* mAgic
* -------------------------------------------------------------------- */
#ifdef CONFIG_MAGICV
static struct resource mAgic_resources[] = {
{
.start = AT91_MAGIC_PM_BASE,
.end = AT91_MAGIC_PM_BASE + AT91_MAGIC_PM_SIZE - 1,
.flags = IORESOURCE_MEM,
},
{
.start = AT91_MAGIC_DM_I_BASE,
.end = AT91_MAGIC_DM_I_BASE + AT91_MAGIC_DM_I_SIZE - 1,
.flags = IORESOURCE_MEM,
},
{
.start = AT91_MAGIC_DM_F_BASE,
.end = AT91_MAGIC_DM_F_BASE + AT91_MAGIC_DM_F_SIZE - 1,
.flags = IORESOURCE_MEM,
},
{
.start = AT91_MAGIC_DM_DB_BASE,
.end = AT91_MAGIC_DM_DB_BASE + AT91_MAGIC_DM_DB_SIZE - 1,
.flags = IORESOURCE_MEM,
},
{
.start = AT91_MAGIC_REGS_BASE,
.end = AT91_MAGIC_REGS_BASE + AT91_MAGIC_REGS_SIZE - 1,
.flags = IORESOURCE_MEM,
},
{
.start = AT91_MAGIC_EXTPAGE_BASE,
.end = AT91_MAGIC_EXTPAGE_BASE + AT91_MAGIC_EXTPAGE_SIZE - 1,
.flags = IORESOURCE_MEM,
},
{
.start = AT572D940HF_ID_MSIRQ0,
.end = AT572D940HF_ID_MSIRQ0,
.flags = IORESOURCE_IRQ,
},
{
.start = AT572D940HF_ID_MHALT,
.end = AT572D940HF_ID_MHALT,
.flags = IORESOURCE_IRQ,
},
{
.start = AT572D940HF_ID_MEXC,
.end = AT572D940HF_ID_MEXC,
.flags = IORESOURCE_IRQ,
},
{
.start = AT572D940HF_ID_MEDMA,
.end = AT572D940HF_ID_MEDMA,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device mAgic_device = {
.name = "mAgic",
.id = -1,
.num_resources = ARRAY_SIZE(mAgic_resources),
.resource = mAgic_resources,
};
void __init at91_add_device_mAgic(void)
{
platform_device_register(&mAgic_device);
}
#else
void __init at91_add_device_mAgic(void) {}
#endif
/* -------------------------------------------------------------------- */
/*
* These devices are always present and don't need any board-specific
* setup.
*/
static int __init at91_add_standard_devices(void)
{
at91_add_device_rtt();
at91_add_device_watchdog();
at91_add_device_tc();
return 0;
}
arch_initcall(at91_add_standard_devices);
arch/arm/mach-at91/board-at572d940hf_ek.c 已删除 100644 → 0
浏览文件 @ e57556e3
/*
* linux/arch/arm/mach-at91/board-at572d940hf_ek.c
*
* Copyright (C) 2008 Atmel Antonio R. Costa <costa.antonior@gmail.com>
* Copyright (C) 2005 SAN People
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/types.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/spi/ds1305.h>
#include <linux/irq.h>
#include <linux/mtd/physmap.h>
#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
#include <mach/system_rev.h>
#include "sam9_smc.h"
#include "generic.h"
static void __init eb_init_early(void)
{
/* Initialize processor: 12.500 MHz crystal */
at572d940hf_initialize(12000000);
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART0 on ttyS1. (Rx & Tx only) */
at91_register_uart(AT572D940HF_ID_US0, 1, 0);
/* USART1 on ttyS2. (Rx & Tx only) */
at91_register_uart(AT572D940HF_ID_US1, 2, 0);
/* USART2 on ttyS3. (Tx & Rx only */
at91_register_uart(AT572D940HF_ID_US2, 3, 0);
/* set serial console to ttyS0 (ie, DBGU) */
at91_set_serial_console(0);
}
static void __init eb_init_irq(void)
{
at572d940hf_init_interrupts(NULL);
}
/*
* USB Host Port
*/
static struct at91_usbh_data __initdata eb_usbh_data = {
.ports = 2,
};
/*
* USB Device Port
*/
static struct at91_udc_data __initdata eb_udc_data = {
.vbus_pin = 0, /* no VBUS detection,UDC always on */
.pullup_pin = 0, /* pull-up driven by UDC */
};
/*
* MCI (SD/MMC)
*/
static struct at91_mmc_data __initdata eb_mmc_data = {
.wire4 = 1,
/* .det_pin = ... not connected */
/* .wp_pin = ... not connected */
/* .vcc_pin = ... not connected */
};
/*
* MACB Ethernet device
*/
static struct at91_eth_data __initdata eb_eth_data = {
.phy_irq_pin = AT91_PIN_PB25,
.is_rmii = 1,
};
/*
* NOR flash
*/
static struct mtd_partition eb_nor_partitions[] = {
{
.name = "Raw Environment",
.offset = 0,
.size = SZ_4M,
.mask_flags = 0,
},
{
.name = "OS FS",
.offset = MTDPART_OFS_APPEND,
.size = 3 * SZ_1M,
.mask_flags = 0,
},
{
.name = "APP FS",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
.mask_flags = 0,
},
};
static void nor_flash_set_vpp(struct map_info* mi, int i) {
};
static struct physmap_flash_data nor_flash_data = {
.width = 4,
.parts = eb_nor_partitions,
.nr_parts = ARRAY_SIZE(eb_nor_partitions),
.set_vpp = nor_flash_set_vpp,
};
static struct resource nor_flash_resources[] = {
{
.start = AT91_CHIPSELECT_0,
.end = AT91_CHIPSELECT_0 + SZ_16M - 1,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device nor_flash = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &nor_flash_data,
},
.resource = nor_flash_resources,
.num_resources = ARRAY_SIZE(nor_flash_resources),
};
static struct sam9_smc_config __initdata eb_nor_smc_config = {
.ncs_read_setup = 1,
.nrd_setup = 1,
.ncs_write_setup = 1,
.nwe_setup = 1,
.ncs_read_pulse = 7,
.nrd_pulse = 7,
.ncs_write_pulse = 7,
.nwe_pulse = 7,
.read_cycle = 9,
.write_cycle = 9,
.mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_32,
.tdf_cycles = 1,
};
static void __init eb_add_device_nor(void)
{
/* configure chip-select 0 (NOR) */
sam9_smc_configure(0, &eb_nor_smc_config);
platform_device_register(&nor_flash);
}
/*
* NAND flash
*/
static struct mtd_partition __initdata eb_nand_partition[] = {
{
.name = "Partition 1",
.offset = 0,
.size = SZ_16M,
},
{
.name = "Partition 2",
.offset = MTDPART_OFS_NXTBLK,
.size = MTDPART_SIZ_FULL,
}
};
static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
{
*num_partitions = ARRAY_SIZE(eb_nand_partition);
return eb_nand_partition;
}
static struct atmel_nand_data __initdata eb_nand_data = {
.ale = 22,
.cle = 21,
/* .det_pin = ... not connected */
/* .rdy_pin = AT91_PIN_PC16, */
.enable_pin = AT91_PIN_PA15,
.partition_info = nand_partitions,
};
static struct sam9_smc_config __initdata eb_nand_smc_config = {
.ncs_read_setup = 0,
.nrd_setup = 0,
.ncs_write_setup = 1,
.nwe_setup = 1,
.ncs_read_pulse = 3,
.nrd_pulse = 3,
.ncs_write_pulse = 3,
.nwe_pulse = 3,
.read_cycle = 5,
.write_cycle = 5,
.mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
.tdf_cycles = 12,
};
static void __init eb_add_device_nand(void)
{
ek_nand_data.bus_width_16 = !board_have_nand_8bit();
/* setup bus-width (8 or 16) */
if (eb_nand_data.bus_width_16)
eb_nand_smc_config.mode |= AT91_SMC_DBW_16;
else
eb_nand_smc_config.mode |= AT91_SMC_DBW_8;
/* configure chip-select 3 (NAND) */
sam9_smc_configure(3, &eb_nand_smc_config);
at91_add_device_nand(&eb_nand_data);
}
/*
* SPI devices
*/
static struct resource rtc_resources[] = {
[0] = {
.start = AT572D940HF_ID_IRQ1,
.end = AT572D940HF_ID_IRQ1,
.flags = IORESOURCE_IRQ,
},
};
static struct ds1305_platform_data ds1306_data = {
.is_ds1306 = true,
.en_1hz = false,
};
static struct spi_board_info eb_spi_devices[] = {
{ /* RTC Dallas DS1306 */
.modalias = "rtc-ds1305",
.chip_select = 3,
.mode = SPI_CS_HIGH | SPI_CPOL | SPI_CPHA,
.max_speed_hz = 500000,
.bus_num = 0,
.irq = AT572D940HF_ID_IRQ1,
.platform_data = (void *) &ds1306_data,
},
#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
{ /* Dataflash card */
.modalias = "mtd_dataflash",
.chip_select = 0,
.max_speed_hz = 15 * 1000 * 1000,
.bus_num = 0,
},
#endif
};
static void __init eb_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&eb_usbh_data);
/* USB Device */
at91_add_device_udc(&eb_udc_data);
/* I2C */
at91_add_device_i2c(NULL, 0);
/* NOR */
eb_add_device_nor();
/* NAND */
eb_add_device_nand();
/* SPI */
at91_add_device_spi(eb_spi_devices, ARRAY_SIZE(eb_spi_devices));
/* MMC */
at91_add_device_mmc(0, &eb_mmc_data);
/* Ethernet */
at91_add_device_eth(&eb_eth_data);
/* mAgic */
at91_add_device_mAgic();
}
MACHINE_START(AT572D940HFEB, "Atmel AT91D940HF-EB")
/* Maintainer: Atmel <costa.antonior@gmail.com> */
.timer = &at91sam926x_timer,
.map_io = at572d940hf_map_io,
.init_early = eb_init_early,
.init_irq = eb_init_irq,
.init_machine = eb_board_init,
MACHINE_END
arch/arm/mach-at91/clock.c
浏览文件 @ 7a2207a0
......@@ -599,7 +599,7 @@ static void __init at91_pllb_usbfs_clock_init(unsigned long main_clock)
at91_sys_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP);
} else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() ||
cpu_is_at91sam9263() || cpu_is_at91sam9g20() ||
cpu_is_at91sam9g10() || cpu_is_at572d940hf()) {
cpu_is_at91sam9g10()) {
uhpck.pmc_mask = AT91SAM926x_PMC_UHP;
udpck.pmc_mask = AT91SAM926x_PMC_UDP;
} else if (cpu_is_at91cap9()) {
......
arch/arm/mach-at91/generic.h
浏览文件 @ 7a2207a0
......@@ -19,7 +19,6 @@ extern void __init at91sam9rl_map_io(void);
extern void __init at91sam9g45_map_io(void);
extern void __init at91x40_map_io(void);
extern void __init at91cap9_map_io(void);
extern void __init at572d940hf_map_io(void);
/* Processors */
extern void __init at91rm9200_set_type(int type);
......@@ -31,7 +30,6 @@ extern void __init at91sam9rl_initialize(unsigned long main_clock);
extern void __init at91sam9g45_initialize(unsigned long main_clock);
extern void __init at91x40_initialize(unsigned long main_clock);
extern void __init at91cap9_initialize(unsigned long main_clock);
extern void __init at572d940hf_initialize(unsigned long main_clock);
/* Interrupts */
extern void __init at91rm9200_init_interrupts(unsigned int priority[]);
......@@ -42,7 +40,6 @@ extern void __init at91sam9rl_init_interrupts(unsigned int priority[]);
extern void __init at91sam9g45_init_interrupts(unsigned int priority[]);
extern void __init at91x40_init_interrupts(unsigned int priority[]);
extern void __init at91cap9_init_interrupts(unsigned int priority[]);
extern void __init at572d940hf_init_interrupts(unsigned int priority[]);
extern void __init at91_aic_init(unsigned int priority[]);
/* Timer */
......@@ -65,7 +62,6 @@ extern void __init at91sam9263_set_console_clock(int id);
extern void __init at91sam9rl_set_console_clock(int id);
extern void __init at91sam9g45_set_console_clock(int id);
extern void __init at91cap9_set_console_clock(int id);
extern void __init at572d940hf_set_console_clock(int id);
struct device;
/* Power Management */
......
arch/arm/mach-at91/include/mach/at572d940hf.h 已删除 100644 → 0
浏览文件 @ e57556e3
/*
* include/mach/at572d940hf.h
*
* Antonio R. Costa <costa.antonior@gmail.com>
* Copyright (C) 2008 Atmel
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
*/
#ifndef AT572D940HF_H
#define AT572D940HF_H
/*
* Peripheral identifiers/interrupts.
*/
#define AT572D940HF_ID_PIOA 2 /* Parallel IO Controller A */
#define AT572D940HF_ID_PIOB 3 /* Parallel IO Controller B */
#define AT572D940HF_ID_PIOC 4 /* Parallel IO Controller C */
#define AT572D940HF_ID_EMAC 5 /* MACB ethernet controller */
#define AT572D940HF_ID_US0 6 /* USART 0 */
#define AT572D940HF_ID_US1 7 /* USART 1 */
#define AT572D940HF_ID_US2 8 /* USART 2 */
#define AT572D940HF_ID_MCI 9 /* Multimedia Card Interface */
#define AT572D940HF_ID_UDP 10 /* USB Device Port */
#define AT572D940HF_ID_TWI0 11 /* Two-Wire Interface 0 */
#define AT572D940HF_ID_SPI0 12 /* Serial Peripheral Interface 0 */
#define AT572D940HF_ID_SPI1 13 /* Serial Peripheral Interface 1 */
#define AT572D940HF_ID_SSC0 14 /* Serial Synchronous Controller 0 */
#define AT572D940HF_ID_SSC1 15 /* Serial Synchronous Controller 1 */
#define AT572D940HF_ID_SSC2 16 /* Serial Synchronous Controller 2 */
#define AT572D940HF_ID_TC0 17 /* Timer Counter 0 */
#define AT572D940HF_ID_TC1 18 /* Timer Counter 1 */
#define AT572D940HF_ID_TC2 19 /* Timer Counter 2 */
#define AT572D940HF_ID_UHP 20 /* USB Host port */
#define AT572D940HF_ID_SSC3 21 /* Serial Synchronous Controller 3 */
#define AT572D940HF_ID_TWI1 22 /* Two-Wire Interface 1 */
#define AT572D940HF_ID_CAN0 23 /* CAN Controller 0 */
#define AT572D940HF_ID_CAN1 24 /* CAN Controller 1 */
#define AT572D940HF_ID_MHALT 25 /* mAgicV HALT line */
#define AT572D940HF_ID_MSIRQ0 26 /* mAgicV SIRQ0 line */
#define AT572D940HF_ID_MEXC 27 /* mAgicV exception line */
#define AT572D940HF_ID_MEDMA 28 /* mAgicV end of DMA line */
#define AT572D940HF_ID_IRQ0 29 /* External Interrupt Source (IRQ0) */
#define AT572D940HF_ID_IRQ1 30 /* External Interrupt Source (IRQ1) */
#define AT572D940HF_ID_IRQ2 31 /* External Interrupt Source (IRQ2) */
/*
* User Peripheral physical base addresses.
*/
#define AT572D940HF_BASE_TCB 0xfffa0000
#define AT572D940HF_BASE_TC0 0xfffa0000
#define AT572D940HF_BASE_TC1 0xfffa0040
#define AT572D940HF_BASE_TC2 0xfffa0080
#define AT572D940HF_BASE_UDP 0xfffa4000
#define AT572D940HF_BASE_MCI 0xfffa8000
#define AT572D940HF_BASE_TWI0 0xfffac000
#define AT572D940HF_BASE_US0 0xfffb0000
#define AT572D940HF_BASE_US1 0xfffb4000
#define AT572D940HF_BASE_US2 0xfffb8000
#define AT572D940HF_BASE_SSC0 0xfffbc000
#define AT572D940HF_BASE_SSC1 0xfffc0000
#define AT572D940HF_BASE_SSC2 0xfffc4000
#define AT572D940HF_BASE_SPI0 0xfffc8000
#define AT572D940HF_BASE_SPI1 0xfffcc000
#define AT572D940HF_BASE_SSC3 0xfffd0000
#define AT572D940HF_BASE_TWI1 0xfffd4000
#define AT572D940HF_BASE_EMAC 0xfffd8000
#define AT572D940HF_BASE_CAN0 0xfffdc000
#define AT572D940HF_BASE_CAN1 0xfffe0000
#define AT91_BASE_SYS 0xffffea00
/*
* System Peripherals (offset from AT91_BASE_SYS)
*/
#define AT91_SDRAMC0 (0xffffea00 - AT91_BASE_SYS)
#define AT91_SMC (0xffffec00 - AT91_BASE_SYS)
#define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS)
#define AT91_AIC (0xfffff000 - AT91_BASE_SYS)
#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS)
#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS)
#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS)
#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS)
#define AT91_PMC (0xfffffc00 - AT91_BASE_SYS)
#define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS)
#define AT91_RTT (0xfffffd20 - AT91_BASE_SYS)
#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS)
#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS)
#define AT91_USART0 AT572D940HF_ID_US0
#define AT91_USART1 AT572D940HF_ID_US1
#define AT91_USART2 AT572D940HF_ID_US2
/*
* Internal Memory.
*/
#define AT572D940HF_SRAM_BASE 0x00300000 /* Internal SRAM base address */
#define AT572D940HF_SRAM_SIZE (48 * SZ_1K) /* Internal SRAM size (48Kb) */
#define AT572D940HF_ROM_BASE 0x00400000 /* Internal ROM base address */
#define AT572D940HF_ROM_SIZE SZ_32K /* Internal ROM size (32Kb) */
#define AT572D940HF_UHP_BASE 0x00500000 /* USB Host controller */
#endif
arch/arm/mach-at91/include/mach/at572d940hf_matrix.h 已删除 100644 → 0
浏览文件 @ e57556e3
/*
* include/mach//at572d940hf_matrix.h
*
* Antonio R. Costa <costa.antonior@gmail.com>
* Copyright (C) 2008 Atmel
*
* Copyright (C) 2005 SAN People
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#ifndef AT572D940HF_MATRIX_H
#define AT572D940HF_MATRIX_H
#define AT91_MATRIX_MCFG0 (AT91_MATRIX + 0x00) /* Master Configuration Register 0 */
#define AT91_MATRIX_MCFG1 (AT91_MATRIX + 0x04) /* Master Configuration Register 1 */
#define AT91_MATRIX_MCFG2 (AT91_MATRIX + 0x08) /* Master Configuration Register 2 */
#define AT91_MATRIX_MCFG3 (AT91_MATRIX + 0x0C) /* Master Configuration Register 3 */
#define AT91_MATRIX_MCFG4 (AT91_MATRIX + 0x10) /* Master Configuration Register 4 */
#define AT91_MATRIX_MCFG5 (AT91_MATRIX + 0x14) /* Master Configuration Register 5 */
#define AT91_MATRIX_ULBT (7 << 0) /* Undefined Length Burst Type */
#define AT91_MATRIX_ULBT_INFINITE (0 << 0)
#define AT91_MATRIX_ULBT_SINGLE (1 << 0)
#define AT91_MATRIX_ULBT_FOUR (2 << 0)
#define AT91_MATRIX_ULBT_EIGHT (3 << 0)
#define AT91_MATRIX_ULBT_SIXTEEN (4 << 0)
#define AT91_MATRIX_SCFG0 (AT91_MATRIX + 0x40) /* Slave Configuration Register 0 */
#define AT91_MATRIX_SCFG1 (AT91_MATRIX + 0x44) /* Slave Configuration Register 1 */
#define AT91_MATRIX_SCFG2 (AT91_MATRIX + 0x48) /* Slave Configuration Register 2 */
#define AT91_MATRIX_SCFG3 (AT91_MATRIX + 0x4C) /* Slave Configuration Register 3 */
#define AT91_MATRIX_SCFG4 (AT91_MATRIX + 0x50) /* Slave Configuration Register 4 */
#define AT91_MATRIX_SLOT_CYCLE (0xff << 0) /* Maximum Number of Allowed Cycles for a Burst */
#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */
#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16)
#define AT91_MATRIX_DEFMSTR_TYPE_LAST (1 << 16)
#define AT91_MATRIX_DEFMSTR_TYPE_FIXED (2 << 16)
#define AT91_MATRIX_FIXED_DEFMSTR (0x7 << 18) /* Fixed Index of Default Master */
#define AT91_MATRIX_ARBT (3 << 24) /* Arbitration Type */
#define AT91_MATRIX_ARBT_ROUND_ROBIN (0 << 24)
#define AT91_MATRIX_ARBT_FIXED_PRIORITY (1 << 24)
#define AT91_MATRIX_PRAS0 (AT91_MATRIX + 0x80) /* Priority Register A for Slave 0 */
#define AT91_MATRIX_PRAS1 (AT91_MATRIX + 0x88) /* Priority Register A for Slave 1 */
#define AT91_MATRIX_PRAS2 (AT91_MATRIX + 0x90) /* Priority Register A for Slave 2 */
#define AT91_MATRIX_PRAS3 (AT91_MATRIX + 0x98) /* Priority Register A for Slave 3 */
#define AT91_MATRIX_PRAS4 (AT91_MATRIX + 0xA0) /* Priority Register A for Slave 4 */
#define AT91_MATRIX_M0PR (3 << 0) /* Master 0 Priority */
#define AT91_MATRIX_M1PR (3 << 4) /* Master 1 Priority */
#define AT91_MATRIX_M2PR (3 << 8) /* Master 2 Priority */
#define AT91_MATRIX_M3PR (3 << 12) /* Master 3 Priority */
#define AT91_MATRIX_M4PR (3 << 16) /* Master 4 Priority */
#define AT91_MATRIX_M5PR (3 << 20) /* Master 5 Priority */
#define AT91_MATRIX_M6PR (3 << 24) /* Master 6 Priority */
#define AT91_MATRIX_MRCR (AT91_MATRIX + 0x100) /* Master Remap Control Register */
#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */
#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */
#define AT91_MATRIX_SFR0 (AT91_MATRIX + 0x110) /* Special Function Register 0 */
#define AT91_MATRIX_SFR1 (AT91_MATRIX + 0x114) /* Special Function Register 1 */
#define AT91_MATRIX_SFR2 (AT91_MATRIX + 0x118) /* Special Function Register 2 */
#define AT91_MATRIX_SFR3 (AT91_MATRIX + 0x11C) /* Special Function Register 3 */
#define AT91_MATRIX_SFR4 (AT91_MATRIX + 0x120) /* Special Function Register 4 */
#define AT91_MATRIX_SFR5 (AT91_MATRIX + 0x124) /* Special Function Register 5 */
#define AT91_MATRIX_SFR6 (AT91_MATRIX + 0x128) /* Special Function Register 6 */
#define AT91_MATRIX_SFR7 (AT91_MATRIX + 0x12C) /* Special Function Register 7 */
#define AT91_MATRIX_SFR8 (AT91_MATRIX + 0x130) /* Special Function Register 8 */
#define AT91_MATRIX_SFR9 (AT91_MATRIX + 0x134) /* Special Function Register 9 */
#define AT91_MATRIX_SFR10 (AT91_MATRIX + 0x138) /* Special Function Register 10 */
#define AT91_MATRIX_SFR11 (AT91_MATRIX + 0x13C) /* Special Function Register 11 */
#define AT91_MATRIX_SFR12 (AT91_MATRIX + 0x140) /* Special Function Register 12 */
#define AT91_MATRIX_SFR13 (AT91_MATRIX + 0x144) /* Special Function Register 13 */
#define AT91_MATRIX_SFR14 (AT91_MATRIX + 0x148) /* Special Function Register 14 */
#define AT91_MATRIX_SFR15 (AT91_MATRIX + 0x14C) /* Special Function Register 15 */
/*
* The following registers / bits are not defined in the Datasheet (Revision A)
*/
#define AT91_MATRIX_TCR (AT91_MATRIX + 0x100) /* TCM Configuration Register */
#define AT91_MATRIX_ITCM_SIZE (0xf << 0) /* Size of ITCM enabled memory block */
#define AT91_MATRIX_ITCM_0 (0 << 0)
#define AT91_MATRIX_ITCM_16 (5 << 0)
#define AT91_MATRIX_ITCM_32 (6 << 0)
#define AT91_MATRIX_ITCM_64 (7 << 0)
#define AT91_MATRIX_DTCM_SIZE (0xf << 4) /* Size of DTCM enabled memory block */
#define AT91_MATRIX_DTCM_0 (0 << 4)
#define AT91_MATRIX_DTCM_16 (5 << 4)
#define AT91_MATRIX_DTCM_32 (6 << 4)
#define AT91_MATRIX_DTCM_64 (7 << 4)
#define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x11C) /* EBI Chip Select Assignment Register */
#define AT91_MATRIX_CS1A (1 << 1) /* Chip Select 1 Assignment */
#define AT91_MATRIX_CS1A_SMC (0 << 1)
#define AT91_MATRIX_CS1A_SDRAMC (1 << 1)
#define AT91_MATRIX_CS3A (1 << 3) /* Chip Select 3 Assignment */
#define AT91_MATRIX_CS3A_SMC (0 << 3)
#define AT91_MATRIX_CS3A_SMC_SMARTMEDIA (1 << 3)
#define AT91_MATRIX_CS4A (1 << 4) /* Chip Select 4 Assignment */
#define AT91_MATRIX_CS4A_SMC (0 << 4)
#define AT91_MATRIX_CS4A_SMC_CF1 (1 << 4)
#define AT91_MATRIX_CS5A (1 << 5) /* Chip Select 5 Assignment */
#define AT91_MATRIX_CS5A_SMC (0 << 5)
#define AT91_MATRIX_CS5A_SMC_CF2 (1 << 5)
#define AT91_MATRIX_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */
#endif
arch/arm/mach-at91/include/mach/board.h
浏览文件 @ 7a2207a0
......@@ -90,7 +90,7 @@ struct at91_eth_data {
extern void __init at91_add_device_eth(struct at91_eth_data *data);
#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9) \
|| defined(CONFIG_ARCH_AT91SAM9G45) || defined(CONFIG_ARCH_AT572D940HF)
|| defined(CONFIG_ARCH_AT91SAM9G45)
#define eth_platform_data at91_eth_data
#endif
......@@ -204,9 +204,6 @@ extern void __init at91_init_leds(u8 cpu_led, u8 timer_led);
extern void __init at91_gpio_leds(struct gpio_led *leds, int nr);
extern void __init at91_pwm_leds(struct gpio_led *leds, int nr);
/* AT572D940HF DSP */
extern void __init at91_add_device_mAgic(void);
/* FIXME: this needs a better location, but gets stuff building again */
extern int at91_suspend_entering_slow_clock(void);
......
arch/arm/mach-at91/include/mach/cpu.h
浏览文件 @ 7a2207a0
......@@ -34,8 +34,6 @@
#define ARCH_ID_AT91SAM9XE256 0x329a93a0
#define ARCH_ID_AT91SAM9XE512 0x329aa3a0
#define ARCH_ID_AT572D940HF 0x0e0303e0
#define ARCH_ID_AT91M40800 0x14080044
#define ARCH_ID_AT91R40807 0x44080746
#define ARCH_ID_AT91M40807 0x14080745
......@@ -188,12 +186,6 @@ extern int rm9200_type;
#define cpu_is_at91cap9_revC() (0)
#endif
#ifdef CONFIG_ARCH_AT572D940HF
#define cpu_is_at572d940hf() (at91_cpu_identify() == ARCH_ID_AT572D940HF)
#else
#define cpu_is_at572d940hf() (0)
#endif
/*
* Since this is ARM, we will never run on any AVR32 CPU. But these
* definitions may reduce clutter in common drivers.
......
arch/arm/mach-at91/include/mach/hardware.h
浏览文件 @ 7a2207a0
......@@ -32,8 +32,6 @@
#include <mach/at91cap9.h>
#elif defined(CONFIG_ARCH_AT91X40)
#include <mach/at91x40.h>
#elif defined(CONFIG_ARCH_AT572D940HF)
#include <mach/at572d940hf.h>
#else
#error "Unsupported AT91 processor"
#endif
......
arch/arm/mach-at91/include/mach/timex.h
浏览文件 @ 7a2207a0
......@@ -82,11 +82,6 @@
#define AT91X40_MASTER_CLOCK 40000000
#define CLOCK_TICK_RATE (AT91X40_MASTER_CLOCK)
#elif defined(CONFIG_ARCH_AT572D940HF)
#define AT572D940HF_MASTER_CLOCK 80000000
#define CLOCK_TICK_RATE (AT572D940HF_MASTER_CLOCK/16)
#endif
#endif
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或