diff --git a/Documentation/networking/phy.txt b/Documentation/networking/phy.txt index 7ab9404a8412088cc9bc9446ea833779b9284697..e017d933d53082b8724bdf24918aede93b02c283 100644 --- a/Documentation/networking/phy.txt +++ b/Documentation/networking/phy.txt @@ -65,6 +65,83 @@ The MDIO bus drivers/net/ethernet/freescale/fsl_pq_mdio.c and an associated DTS file for one of the users. (e.g. "git grep fsl,.*-mdio arch/powerpc/boot/dts/") +(RG)MII/electrical interface considerations + + The Reduced Gigabit Medium Independent Interface (RGMII) is a 12-pin + electrical signal interface using a synchronous 125Mhz clock signal and several + data lines. Due to this design decision, a 1.5ns to 2ns delay must be added + between the clock line (RXC or TXC) and the data lines to let the PHY (clock + sink) have enough setup and hold times to sample the data lines correctly. The + PHY library offers different types of PHY_INTERFACE_MODE_RGMII* values to let + the PHY driver and optionally the MAC driver, implement the required delay. The + values of phy_interface_t must be understood from the perspective of the PHY + device itself, leading to the following: + + * PHY_INTERFACE_MODE_RGMII: the PHY is not responsible for inserting any + internal delay by itself, it assumes that either the Ethernet MAC (if capable + or the PCB traces) insert the correct 1.5-2ns delay + + * PHY_INTERFACE_MODE_RGMII_TXID: the PHY should insert an internal delay + for the transmit data lines (TXD[3:0]) processed by the PHY device + + * PHY_INTERFACE_MODE_RGMII_RXID: the PHY should insert an internal delay + for the receive data lines (RXD[3:0]) processed by the PHY device + + * PHY_INTERFACE_MODE_RGMII_ID: the PHY should insert internal delays for + both transmit AND receive data lines from/to the PHY device + + Whenever possible, use the PHY side RGMII delay for these reasons: + + * PHY devices may offer sub-nanosecond granularity in how they allow a + receiver/transmitter side delay (e.g: 0.5, 1.0, 1.5ns) to be specified. Such + precision may be required to account for differences in PCB trace lengths + + * PHY devices are typically qualified for a large range of applications + (industrial, medical, automotive...), and they provide a constant and + reliable delay across temperature/pressure/voltage ranges + + * PHY device drivers in PHYLIB being reusable by nature, being able to + configure correctly a specified delay enables more designs with similar delay + requirements to be operate correctly + + For cases where the PHY is not capable of providing this delay, but the + Ethernet MAC driver is capable of doing so, the correct phy_interface_t value + should be PHY_INTERFACE_MODE_RGMII, and the Ethernet MAC driver should be + configured correctly in order to provide the required transmit and/or receive + side delay from the perspective of the PHY device. Conversely, if the Ethernet + MAC driver looks at the phy_interface_t value, for any other mode but + PHY_INTERFACE_MODE_RGMII, it should make sure that the MAC-level delays are + disabled. + + In case neither the Ethernet MAC, nor the PHY are capable of providing the + required delays, as defined per the RGMII standard, several options may be + available: + + * Some SoCs may offer a pin pad/mux/controller capable of configuring a given + set of pins'strength, delays, and voltage; and it may be a suitable + option to insert the expected 2ns RGMII delay. + + * Modifying the PCB design to include a fixed delay (e.g: using a specifically + designed serpentine), which may not require software configuration at all. + +Common problems with RGMII delay mismatch + + When there is a RGMII delay mismatch between the Ethernet MAC and the PHY, this + will most likely result in the clock and data line signals to be unstable when + the PHY or MAC take a snapshot of these signals to translate them into logical + 1 or 0 states and reconstruct the data being transmitted/received. Typical + symptoms include: + + * Transmission/reception partially works, and there is frequent or occasional + packet loss observed + + * Ethernet MAC may report some or all packets ingressing with a FCS/CRC error, + or just discard them all + + * Switching to lower speeds such as 10/100Mbits/sec makes the problem go away + (since there is enough setup/hold time in that case) + + Connecting to a PHY Sometime during startup, the network driver needs to establish a connection @@ -127,8 +204,9 @@ Letting the PHY Abstraction Layer do Everything values pruned from them which don't make sense for your controller (a 10/100 controller may be connected to a gigabit capable PHY, so you would need to mask off SUPPORTED_1000baseT*). See include/linux/ethtool.h for definitions - for these bitfields. Note that you should not SET any bits, or the PHY may - get put into an unsupported state. + for these bitfields. Note that you should not SET any bits, except the + SUPPORTED_Pause and SUPPORTED_AsymPause bits (see below), or the PHY may get + put into an unsupported state. Lastly, once the controller is ready to handle network traffic, you call phy_start(phydev). This tells the PAL that you are ready, and configures the @@ -139,6 +217,19 @@ Letting the PHY Abstraction Layer do Everything When you want to disconnect from the network (even if just briefly), you call phy_stop(phydev). +Pause frames / flow control + + The PHY does not participate directly in flow control/pause frames except by + making sure that the SUPPORTED_Pause and SUPPORTED_AsymPause bits are set in + MII_ADVERTISE to indicate towards the link partner that the Ethernet MAC + controller supports such a thing. Since flow control/pause frames generation + involves the Ethernet MAC driver, it is recommended that this driver takes care + of properly indicating advertisement and support for such features by setting + the SUPPORTED_Pause and SUPPORTED_AsymPause bits accordingly. This can be done + either before or after phy_connect() and/or as a result of implementing the + ethtool::set_pauseparam feature. + + Keeping Close Tabs on the PAL It is possible that the PAL's built-in state machine needs a little help to @@ -251,39 +342,8 @@ Writing a PHY driver PHY_BASIC_FEATURES, but you can look in include/mii.h for other features. - Each driver consists of a number of function pointers: - - soft_reset: perform a PHY software reset - config_init: configures PHY into a sane state after a reset. - For instance, a Davicom PHY requires descrambling disabled. - probe: Allocate phy->priv, optionally refuse to bind. - PHY may not have been reset or had fixups run yet. - suspend/resume: power management - config_aneg: Changes the speed/duplex/negotiation settings - aneg_done: Determines the auto-negotiation result - read_status: Reads the current speed/duplex/negotiation settings - ack_interrupt: Clear a pending interrupt - did_interrupt: Checks if the PHY generated an interrupt - config_intr: Enable or disable interrupts - remove: Does any driver take-down - ts_info: Queries about the HW timestamping status - match_phy_device: used for Clause 45 capable PHYs to match devices - in package and ensure they are compatible - hwtstamp: Set the PHY HW timestamping configuration - rxtstamp: Requests a receive timestamp at the PHY level for a 'skb' - txtsamp: Requests a transmit timestamp at the PHY level for a 'skb' - set_wol: Enable Wake-on-LAN at the PHY level - get_wol: Get the Wake-on-LAN status at the PHY level - link_change_notify: called to inform the core is about to change the - link state, can be used to work around bogus PHY between state changes - read_mmd_indirect: Read PHY MMD indirect register - write_mmd_indirect: Write PHY MMD indirect register - module_info: Get the size and type of an EEPROM contained in an plug-in - module - module_eeprom: Get EEPROM information of a plug-in module - get_sset_count: Get number of strings sets that get_strings will count - get_strings: Get strings from requested objects (statistics) - get_stats: Get the extended statistics from the PHY device + Each driver consists of a number of function pointers, documented + in include/linux/phy.h under the phy_driver structure. Of these, only config_aneg and read_status are required to be assigned by the driver code. The rest are optional. Also, it is @@ -347,3 +407,13 @@ Board Fixups The stubs set one of the two matching criteria, and set the other one to match anything. +Standards + + IEEE Standard 802.3: CSMA/CD Access Method and Physical Layer Specifications, Section Two: + http://standards.ieee.org/getieee802/download/802.3-2008_section2.pdf + + RGMII v1.3: + http://web.archive.org/web/20160303212629/http://www.hp.com/rnd/pdfs/RGMIIv1_3.pdf + + RGMII v2.0: + http://web.archive.org/web/20160303171328/http://www.hp.com/rnd/pdfs/RGMIIv2_0_final_hp.pdf