提交 5ac072e1 编写于 作者: K Kuninori Morimoto 提交者: Paul Mundt

sh: Urquell board support.

This adds preliminary support for the SH7786-based Urquell board.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
上级 37042fbd
...@@ -162,6 +162,11 @@ config SH_SH7785LCR_29BIT_PHYSMAPS ...@@ -162,6 +162,11 @@ config SH_SH7785LCR_29BIT_PHYSMAPS
DIP switch(S2-5). If you set the DIP switch for S2-5 = ON, DIP switch(S2-5). If you set the DIP switch for S2-5 = ON,
you can access all on-board device in 29bit address mode. you can access all on-board device in 29bit address mode.
config SH_URQUELL
bool "Urquell"
depends on CPU_SUBTYPE_SH7786
select ARCH_REQUIRE_GPIOLIB
config SH_MIGOR config SH_MIGOR
bool "Migo-R" bool "Migo-R"
depends on CPU_SUBTYPE_SH7722 depends on CPU_SUBTYPE_SH7722
......
...@@ -4,5 +4,6 @@ ...@@ -4,5 +4,6 @@
obj-$(CONFIG_SH_AP325RXA) += board-ap325rxa.o obj-$(CONFIG_SH_AP325RXA) += board-ap325rxa.o
obj-$(CONFIG_SH_MAGIC_PANEL_R2) += board-magicpanelr2.o obj-$(CONFIG_SH_MAGIC_PANEL_R2) += board-magicpanelr2.o
obj-$(CONFIG_SH_SH7785LCR) += board-sh7785lcr.o obj-$(CONFIG_SH_SH7785LCR) += board-sh7785lcr.o
obj-$(CONFIG_SH_URQUELL) += board-urquell.o
obj-$(CONFIG_SH_SHMIN) += board-shmin.o obj-$(CONFIG_SH_SHMIN) += board-shmin.o
obj-$(CONFIG_SH_EDOSK7760) += board-edosk7760.o obj-$(CONFIG_SH_EDOSK7760) += board-edosk7760.o
/*
* Renesas Technology Corp. SH7786 Urquell Support.
*
* Copyright (C) 2008 Kuninori Morimoto <morimoto.kuninori@renesas.com>
* Copyright (C) 2008 Yoshihiro Shimoda
*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/fb.h>
#include <linux/mtd/physmap.h>
#include <linux/delay.h>
#include <linux/gpio.h>
#include <linux/irq.h>
#include <mach/urquell.h>
#include <cpu/sh7786.h>
#include <asm/heartbeat.h>
#include <asm/sizes.h>
static struct resource heartbeat_resources[] = {
[0] = {
.start = BOARDREG(SLEDR),
.end = BOARDREG(SLEDR),
.flags = IORESOURCE_MEM,
},
};
static struct heartbeat_data heartbeat_data = {
.regsize = 16,
};
static struct platform_device heartbeat_device = {
.name = "heartbeat",
.id = -1,
.dev = {
.platform_data = &heartbeat_data,
},
.num_resources = ARRAY_SIZE(heartbeat_resources),
.resource = heartbeat_resources,
};
static struct mtd_partition nor_flash_partitions[] = {
{
.name = "loader",
.offset = 0x00000000,
.size = SZ_512K,
.mask_flags = MTD_WRITEABLE, /* Read-only */
},
{
.name = "bootenv",
.offset = MTDPART_OFS_APPEND,
.size = SZ_512K,
.mask_flags = MTD_WRITEABLE, /* Read-only */
},
{
.name = "kernel",
.offset = MTDPART_OFS_APPEND,
.size = SZ_4M,
},
{
.name = "data",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
},
};
static struct physmap_flash_data nor_flash_data = {
.width = 2,
.parts = nor_flash_partitions,
.nr_parts = ARRAY_SIZE(nor_flash_partitions),
};
static struct resource nor_flash_resources[] = {
[0] = {
.start = NOR_FLASH_ADDR,
.end = NOR_FLASH_ADDR + NOR_FLASH_SIZE - 1,
.flags = IORESOURCE_MEM,
}
};
static struct platform_device nor_flash_device = {
.name = "physmap-flash",
.dev = {
.platform_data = &nor_flash_data,
},
.num_resources = ARRAY_SIZE(nor_flash_resources),
.resource = nor_flash_resources,
};
static struct platform_device *urquell_devices[] __initdata = {
&heartbeat_device,
&nor_flash_device,
};
static int __init urquell_devices_setup(void)
{
/* USB */
gpio_request(GPIO_FN_USB_OVC0, NULL);
gpio_request(GPIO_FN_USB_PENC0, NULL);
return platform_add_devices(urquell_devices,
ARRAY_SIZE(urquell_devices));
}
device_initcall(urquell_devices_setup);
static void urquell_power_off(void)
{
__raw_writew(0xa5a5, UBOARDREG(SRSTR));
}
/* Initialize the board */
static void __init urquell_setup(char **cmdline_p)
{
printk(KERN_INFO "Renesas Technology Corp. Urquell support.\n");
pm_power_off = urquell_power_off;
}
/*
* The Machine Vector
*/
static struct sh_machine_vector mv_urquell __initmv = {
.mv_name = "Urquell",
.mv_setup = urquell_setup,
};
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.29-rc4
# Tue Mar 3 16:20:09 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_ARCH_DEFCONFIG="arch/sh/configs/shx3_defconfig"
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_SUSPEND_POSSIBLE is not set
# CONFIG_ARCH_HIBERNATION_POSSIBLE is not set
CONFIG_SYS_SUPPORTS_NUMA=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
# General setup
#
# CONFIG_EXPERIMENTAL is not set
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
# CONFIG_SYSVIPC is not set
# CONFIG_BSD_PROCESS_ACCT is not set
#
# RCU Subsystem
#
CONFIG_CLASSIC_RCU=y
# CONFIG_TREE_RCU is not set
# CONFIG_PREEMPT_RCU is not set
# CONFIG_TREE_RCU_TRACE is not set
# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=17
# CONFIG_CGROUPS is not set
# CONFIG_RELAY is not set
# CONFIG_NAMESPACES is not set
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_EMBEDDED=y
# CONFIG_UID16 is not set
# CONFIG_SYSCTL_SYSCALL is not set
# CONFIG_KALLSYMS is not set
# CONFIG_HOTPLUG is not set
# CONFIG_PRINTK is not set
# CONFIG_BUG is not set
# CONFIG_ELF_CORE is not set
# CONFIG_COMPAT_BRK is not set
# CONFIG_BASE_FULL is not set
# CONFIG_FUTEX is not set
# CONFIG_EPOLL is not set
# CONFIG_SIGNALFD is not set
# CONFIG_TIMERFD is not set
# CONFIG_EVENTFD is not set
CONFIG_SHMEM=y
# CONFIG_AIO is not set
# CONFIG_VM_EVENT_COUNTERS is not set
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_BASE_SMALL=1
# CONFIG_MODULES is not set
# CONFIG_BLOCK is not set
# CONFIG_FREEZER is not set
#
# System type
#
CONFIG_CPU_SH4=y
CONFIG_CPU_SH4A=y
CONFIG_CPU_SHX3=y
# CONFIG_CPU_SUBTYPE_SH7619 is not set
# CONFIG_CPU_SUBTYPE_SH7201 is not set
# CONFIG_CPU_SUBTYPE_SH7203 is not set
# CONFIG_CPU_SUBTYPE_SH7206 is not set
# CONFIG_CPU_SUBTYPE_SH7263 is not set
# CONFIG_CPU_SUBTYPE_MXG is not set
# CONFIG_CPU_SUBTYPE_SH7705 is not set
# CONFIG_CPU_SUBTYPE_SH7706 is not set
# CONFIG_CPU_SUBTYPE_SH7707 is not set
# CONFIG_CPU_SUBTYPE_SH7708 is not set
# CONFIG_CPU_SUBTYPE_SH7709 is not set
# CONFIG_CPU_SUBTYPE_SH7710 is not set
# CONFIG_CPU_SUBTYPE_SH7712 is not set
# CONFIG_CPU_SUBTYPE_SH7720 is not set
# CONFIG_CPU_SUBTYPE_SH7721 is not set
# CONFIG_CPU_SUBTYPE_SH7750 is not set
# CONFIG_CPU_SUBTYPE_SH7091 is not set
# CONFIG_CPU_SUBTYPE_SH7750R is not set
# CONFIG_CPU_SUBTYPE_SH7750S is not set
# CONFIG_CPU_SUBTYPE_SH7751 is not set
# CONFIG_CPU_SUBTYPE_SH7751R is not set
# CONFIG_CPU_SUBTYPE_SH7760 is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
# CONFIG_CPU_SUBTYPE_SH7785 is not set
CONFIG_CPU_SUBTYPE_SH7786=y
# CONFIG_CPU_SUBTYPE_SHX3 is not set
# CONFIG_CPU_SUBTYPE_SH7343 is not set
# CONFIG_CPU_SUBTYPE_SH7722 is not set
# CONFIG_CPU_SUBTYPE_SH7366 is not set
# CONFIG_CPU_SUBTYPE_SH5_101 is not set
# CONFIG_CPU_SUBTYPE_SH5_103 is not set
#
# Memory management options
#
CONFIG_QUICKLIST=y
CONFIG_MMU=y
CONFIG_PAGE_OFFSET=0x80000000
CONFIG_MEMORY_START=0x08000000
CONFIG_MEMORY_SIZE=0x04000000
CONFIG_29BIT=y
CONFIG_VSYSCALL=y
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_DEFAULT=y
CONFIG_MAX_ACTIVE_REGIONS=1
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
CONFIG_PAGE_SIZE_4KB=y
# CONFIG_PAGE_SIZE_8KB is not set
# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
CONFIG_ENTRY_OFFSET=0x00001000
CONFIG_SELECT_MEMORY_MODEL=y
# CONFIG_FLATMEM_MANUAL is not set
# CONFIG_DISCONTIGMEM_MANUAL is not set
CONFIG_SPARSEMEM_MANUAL=y
CONFIG_SPARSEMEM=y
CONFIG_HAVE_MEMORY_PRESENT=y
CONFIG_SPARSEMEM_STATIC=y
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MIGRATION=y
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_NR_QUICK=2
CONFIG_UNEVICTABLE_LRU=y
#
# Cache configuration
#
# CONFIG_SH_DIRECT_MAPPED is not set
CONFIG_CACHE_WRITEBACK=y
# CONFIG_CACHE_WRITETHROUGH is not set
# CONFIG_CACHE_OFF is not set
#
# Processor features
#
CONFIG_CPU_LITTLE_ENDIAN=y
# CONFIG_CPU_BIG_ENDIAN is not set
CONFIG_SH_FPU=y
# CONFIG_SH_STORE_QUEUES is not set
CONFIG_CPU_HAS_INTEVT=y
CONFIG_CPU_HAS_SR_RB=y
CONFIG_CPU_HAS_FPU=y
#
# Board support
#
CONFIG_SH_URQUELL=y
#
# Timer and clock configuration
#
CONFIG_SH_TMU=y
CONFIG_SH_TIMER_IRQ=16
CONFIG_SH_PCLK_FREQ=31250000
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set
#
# DMA support
#
# CONFIG_SH_DMA is not set
#
# Companion Chips
#
#
# Additional SuperH Device Drivers
#
CONFIG_HEARTBEAT=y
# CONFIG_PUSH_SWITCH is not set
#
# Kernel features
#
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
CONFIG_SCHED_HRTICK=y
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
CONFIG_GUSA=y
#
# Boot options
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
# CONFIG_CMDLINE_BOOL is not set
#
# Bus options
#
# CONFIG_ARCH_SUPPORTS_MSI is not set
#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
# CONFIG_HAVE_AOUT is not set
# CONFIG_BINFMT_MISC is not set
# CONFIG_NET is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
# CONFIG_PREVENT_FIRMWARE_BUILD is not set
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
# CONFIG_MTD_PARTITIONS is not set
#
# User Modules And Translation Layers
#
# CONFIG_MTD_CHAR is not set
# CONFIG_MTD_OOPS is not set
#
# RAM/ROM/Flash chip drivers
#
CONFIG_MTD_CFI=y
CONFIG_MTD_JEDECPROBE=y
CONFIG_MTD_GEN_PROBE=y
# CONFIG_MTD_CFI_ADV_OPTIONS is not set
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
# CONFIG_MTD_CFI_INTELEXT is not set
# CONFIG_MTD_CFI_AMDSTD is not set
# CONFIG_MTD_CFI_STAA is not set
CONFIG_MTD_CFI_UTIL=y
# CONFIG_MTD_RAM is not set
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
#
# Mapping drivers for chip access
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
CONFIG_MTD_PHYSMAP=y
# CONFIG_MTD_PHYSMAP_COMPAT is not set
# CONFIG_MTD_PLATRAM is not set
#
# Self-contained MTD device drivers
#
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
#
# Disk-On-Chip Device Drivers
#
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
# CONFIG_MTD_NAND is not set
# CONFIG_MTD_ONENAND is not set
#
# LPDDR flash memory drivers
#
# CONFIG_MTD_LPDDR is not set
# CONFIG_MTD_QINFO_PROBE is not set
#
# UBI - Unsorted block images
#
# CONFIG_MTD_UBI is not set
# CONFIG_PARPORT is not set
# CONFIG_MISC_DEVICES is not set
CONFIG_HAVE_IDE=y
#
# SCSI device support
#
# CONFIG_SCSI_DMA is not set
# CONFIG_SCSI_NETLINK is not set
# CONFIG_PHONE is not set
#
# Input device support
#
# CONFIG_INPUT is not set
#
# Hardware I/O ports
#
# CONFIG_SERIO is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
# CONFIG_VT is not set
# CONFIG_DEVKMEM is not set
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
# CONFIG_SERIAL_8250 is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_SH_SCI=y
CONFIG_SERIAL_SH_SCI_NR_UARTS=6
CONFIG_SERIAL_SH_SCI_CONSOLE=y
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_UNIX98_PTYS is not set
# CONFIG_LEGACY_PTYS is not set
# CONFIG_IPMI_HANDLER is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_R3964 is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
CONFIG_ARCH_REQUIRE_GPIOLIB=y
CONFIG_GPIOLIB=y
#
# Memory mapped GPIO expanders:
#
#
# I2C GPIO expanders:
#
#
# PCI GPIO expanders:
#
#
# SPI GPIO expanders:
#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
#
# Sonics Silicon Backplane
#
# CONFIG_SSB is not set
#
# Multifunction device drivers
#
# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_REGULATOR is not set
#
# Multimedia devices
#
#
# Multimedia core support
#
# CONFIG_VIDEO_DEV is not set
# CONFIG_VIDEO_MEDIA is not set
#
# Multimedia drivers
#
# CONFIG_DAB is not set
#
# Graphics support
#
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_FB is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
# CONFIG_SOUND is not set
# CONFIG_USB_SUPPORT is not set
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_CLASS is not set
# CONFIG_DMADEVICES is not set
# CONFIG_UIO is not set
# CONFIG_STAGING is not set
#
# File systems
#
# CONFIG_DNOTIFY is not set
# CONFIG_INOTIFY is not set
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
#
# Pseudo filesystems
#
# CONFIG_PROC_FS is not set
# CONFIG_SYSFS is not set
# CONFIG_TMPFS is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_MISC_FILESYSTEMS is not set
# CONFIG_NLS is not set
#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
# CONFIG_ENABLE_WARN_DEPRECATED is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_LATENCYTOP is not set
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
#
# Tracers
#
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
# CONFIG_MORE_COMPILE_OPTIONS is not set
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITYFS is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
# CONFIG_CRYPTO is not set
#
# Library routines
#
CONFIG_GENERIC_FIND_LAST_BIT=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
# CONFIG_CRC32 is not set
# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
#ifndef __MACH_URQUELL_H
#define __MACH_URQUELL_H
/*
* ------ 0x00000000 ------------------------------------
* CS0 | (SW1,SW47) EEPROM, SRAM, NOR FLASH
* -----+ 0x04000000 ------------------------------------
* CS1 | (SW47) SRAM, SRAM-LAN-PCMCIA, NOR FLASH
* -----+ 0x08000000 ------------------------------------
* CS2 | DDR3
* CS3 |
* -----+ 0x10000000 ------------------------------------
* CS4 | PCIe
* -----+ 0x14000000 ------------------------------------
* CS5 | (SW47) LRAM/URAM, SRAM-LAN-PCMCIA
* -----+ 0x18000000 ------------------------------------
* CS6 | ATA, NAND FLASH
* -----+ 0x1c000000 ------------------------------------
* CS7 | SH7786 register
* -----+------------------------------------------------
*/
#define NOR_FLASH_ADDR 0x00000000
#define NOR_FLASH_SIZE 0x04000000
#define CS1_BASE 0x05000000
#define CS5_BASE 0x15000000
#define FPGA_BASE CS1_BASE
#define BOARDREG(ofs) (FPGA_BASE + ofs##_OFS)
#define UBOARDREG(ofs) (0xa0000000 + FPGA_BASE + ofs##_OFS)
#define SRSTR_OFS 0x0000 /* System reset register */
#define BDMR_OFS 0x0010 /* Board operating mode resister */
#define IRL0SR_OFS 0x0020 /* IRL0 Status register */
#define IRL0MSKR_OFS 0x0030 /* IRL0 Mask register */
#define IRL1SR_OFS 0x0040 /* IRL1 Status register */
#define IRL1MSKR_OFS 0x0050 /* IRL1 Mask register */
#define IRL2SR_OFS 0x0060 /* IRL2 Status register */
#define IRL2MSKR_OFS 0x0070 /* IRL2 Mask register */
#define IRL3SR_OFS 0x0080 /* IRL3 Status register */
#define IRL3MSKR_OFS 0x0090 /* IRL3 Mask register */
#define SOFTINTR_OFS 0x0120 /* Softwear Interrupt register */
#define SLEDR_OFS 0x0130 /* LED control resister */
#define MAPSCIFSWR_OFS 0x0140 /* Map/SCIF Switch register */
#define FPVERR_OFS 0x0150 /* FPGA Version register */
#define FPDATER_OFS 0x0160 /* FPGA Date register */
#define FPYEARR_OFS 0x0170 /* FPGA Year register */
#define TCLKCR_OFS 0x0180 /* TCLK Control register */
#define DIPSWMR_OFS 0x1000 /* DIPSW monitor register */
#define FPODR_OFS 0x1010 /* Output port data register */
#define ATACNR_OFS 0x1020 /* ATA-CN Control/status register */
#define FPINDR_OFS 0x1030 /* Input port data register */
#define MDSWMR_OFS 0x1040 /* MODE SW monitor register */
#define DDR3BUPCR_OFS 0x1050 /* DDR3 Backup control register */
#define SSICODECCR_OFS 0x1060 /* SSI-CODEC control register */
#define PCIESLOTSR_OFS 0x1070 /* PCIexpress Slot status register */
#define ETHERPORTSR_OFS 0x1080 /* EtherPhy Port status register */
#define LATCHCR_OFS 0x3000 /* Latch control register */
#define LATCUAR_OFS 0x3010 /* Latch upper address register */
#define LATCLAR_OFS 0x3012 /* Latch lower address register */
#define LATCLUDR_OFS 0x3024 /* Latch D31-16 register */
#define LATCLLDR_OFS 0x3026 /* Latch D15-0 register */
#define CHARLED_OFS 0x2000 /* Character LED */
#endif /* __MACH_URQUELL_H */
...@@ -52,3 +52,4 @@ RSK7203 SH_RSK7203 ...@@ -52,3 +52,4 @@ RSK7203 SH_RSK7203
AP325RXA SH_AP325RXA AP325RXA SH_AP325RXA
SH7763RDP SH_SH7763RDP SH7763RDP SH_SH7763RDP
SH7785LCR SH_SH7785LCR SH7785LCR SH_SH7785LCR
URQUELL SH_URQUELL
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册