Merge branch 'sdhci_omap' into next

Merge immutable branch for sdhci-omap to add UHS/HS200 mode support.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Documentation/devicetree/bindings/mmc/sdhci-omap.txt

@@ -4,7 +4,14 @@ Refer to mmc.txt for standard MMC bindings.
 
 Required properties:
 - compatible: Should be "ti,dra7-sdhci" for DRA7 and DRA72 controllers
+	      Should be "ti,k2g-sdhci" for K2G
 - ti,hwmods: Must be "mmc<n>", <n> is controller instance starting 1
+	     (Not required for K2G).
+- pinctrl-names: Should be subset of "default", "hs", "sdr12", "sdr25", "sdr50",
+		 "ddr50-rev11", "sdr104-rev11", "ddr50", "sdr104",
+		 "ddr_1_8v-rev11", "ddr_1_8v" or "ddr_3_3v", "hs200_1_8v-rev11",
+		 "hs200_1_8v",
+- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt
 
 Example:
 	mmc1: mmc@4809c000 {

drivers/mmc/host/sdhci-omap.c

@@ -26,6 +26,7 @@
 #include <linux/pm_runtime.h>
 #include <linux/regulator/consumer.h>
 #include <linux/pinctrl/consumer.h>
+#include <linux/sys_soc.h>
 
 #include "sdhci-pltfm.h"
 
@@ -35,6 +36,7 @@
 #define CON_DDR			BIT(19)
 #define CON_CLKEXTFREE		BIT(16)
 #define CON_PADEN		BIT(15)
+#define CON_CTPL		BIT(11)
 #define CON_INIT		BIT(1)
 #define CON_OD			BIT(0)
 
@@ -100,6 +102,7 @@ struct sdhci_omap_data {
 };
 
 struct sdhci_omap_host {
+	char			*version;
 	void __iomem		*base;
 	struct device		*dev;
 	struct	regulator	*pbias;
@@ -224,6 +227,23 @@ static void sdhci_omap_conf_bus_power(struct sdhci_omap_host *omap_host,
 	}
 }
 
+static void sdhci_omap_enable_sdio_irq(struct mmc_host *mmc, int enable)
+{
+	struct sdhci_host *host = mmc_priv(mmc);
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
+	u32 reg;
+
+	reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
+	if (enable)
+		reg |= (CON_CTPL | CON_CLKEXTFREE);
+	else
+		reg &= ~(CON_CTPL | CON_CLKEXTFREE);
+	sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg);
+
+	sdhci_enable_sdio_irq(mmc, enable);
+}
+
 static inline void sdhci_omap_set_dll(struct sdhci_omap_host *omap_host,
 				      int count)
 {
@@ -713,10 +733,15 @@ static const struct sdhci_pltfm_data sdhci_omap_pdata = {
 		  SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC,
 	.quirks2 = SDHCI_QUIRK2_ACMD23_BROKEN |
 		   SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
-		   SDHCI_QUIRK2_RSP_136_HAS_CRC,
+		   SDHCI_QUIRK2_RSP_136_HAS_CRC |
+		   SDHCI_QUIRK2_DISABLE_HW_TIMEOUT,
 	.ops = &sdhci_omap_ops,
 };
 
+static const struct sdhci_omap_data k2g_data = {
+	.offset = 0x200,
+};
+
 static const struct sdhci_omap_data dra7_data = {
 	.offset = 0x200,
 	.flags	= SDHCI_OMAP_REQUIRE_IODELAY,
@@ -724,6 +749,7 @@ static const struct sdhci_omap_data dra7_data = {
 
 static const struct of_device_id omap_sdhci_match[] = {
 	{ .compatible = "ti,dra7-sdhci", .data = &dra7_data },
+	{ .compatible = "ti,k2g-sdhci", .data = &k2g_data },
 	{},
 };
 MODULE_DEVICE_TABLE(of, omap_sdhci_match);
@@ -733,12 +759,21 @@ static struct pinctrl_state
 				  u32 *caps, u32 capmask)
 {
 	struct device *dev = omap_host->dev;
+	char *version = omap_host->version;
 	struct pinctrl_state *pinctrl_state = ERR_PTR(-ENODEV);
+	char str[20];
 
 	if (!(*caps & capmask))
 		goto ret;
 
+	if (version) {
+		snprintf(str, 20, "%s-%s", mode, version);
+		pinctrl_state = pinctrl_lookup_state(omap_host->pinctrl, str);
+	}
+
+	if (IS_ERR(pinctrl_state))
 		pinctrl_state = pinctrl_lookup_state(omap_host->pinctrl, mode);
+
 	if (IS_ERR(pinctrl_state)) {
 		dev_err(dev, "no pinctrl state for %s mode", mode);
 		*caps &= ~capmask;
@@ -807,8 +842,15 @@ static int sdhci_omap_config_iodelay_pinctrl_state(struct sdhci_omap_host
 
 	state = sdhci_omap_iodelay_pinctrl_state(omap_host, "ddr_1_8v", caps,
 						 MMC_CAP_1_8V_DDR);
+	if (!IS_ERR(state)) {
+		pinctrl_state[MMC_TIMING_MMC_DDR52] = state;
+	} else {
+		state = sdhci_omap_iodelay_pinctrl_state(omap_host, "ddr_3_3v",
+							 caps,
+							 MMC_CAP_3_3V_DDR);
 		if (!IS_ERR(state))
 			pinctrl_state[MMC_TIMING_MMC_DDR52] = state;
+	}
 
 	state = sdhci_omap_iodelay_pinctrl_state(omap_host, "hs", caps,
 						 MMC_CAP_SD_HIGHSPEED);
@@ -830,6 +872,16 @@ static int sdhci_omap_config_iodelay_pinctrl_state(struct sdhci_omap_host
 	return 0;
 }
 
+static const struct soc_device_attribute sdhci_omap_soc_devices[] = {
+	{
+		.machine = "DRA7[45]*",
+		.revision = "ES1.[01]",
+	},
+	{
+		/* sentinel */
+	}
+};
+
 static int sdhci_omap_probe(struct platform_device *pdev)
 {
 	int ret;
@@ -841,6 +893,7 @@ static int sdhci_omap_probe(struct platform_device *pdev)
 	struct mmc_host *mmc;
 	const struct of_device_id *match;
 	struct sdhci_omap_data *data;
+	const struct soc_device_attribute *soc;
 
 	match = of_match_device(omap_sdhci_match, dev);
 	if (!match)
@@ -871,10 +924,22 @@ static int sdhci_omap_probe(struct platform_device *pdev)
 	host->ioaddr += offset;
 
 	mmc = host->mmc;
+	sdhci_get_of_property(pdev);
 	ret = mmc_of_parse(mmc);
 	if (ret)
 		goto err_pltfm_free;
 
+	soc = soc_device_match(sdhci_omap_soc_devices);
+	if (soc) {
+		omap_host->version = "rev11";
+		if (!strcmp(dev_name(dev), "4809c000.mmc"))
+			mmc->f_max = 96000000;
+		if (!strcmp(dev_name(dev), "480b4000.mmc"))
+			mmc->f_max = 48000000;
+		if (!strcmp(dev_name(dev), "480ad000.mmc"))
+			mmc->f_max = 48000000;
+	}
+
 	pltfm_host->clk = devm_clk_get(dev, "fck");
 	if (IS_ERR(pltfm_host->clk)) {
 		ret = PTR_ERR(pltfm_host->clk);
@@ -916,26 +981,31 @@ static int sdhci_omap_probe(struct platform_device *pdev)
 		goto err_put_sync;
 	}
 
-	ret = sdhci_omap_config_iodelay_pinctrl_state(omap_host);
-	if (ret)
-		goto err_put_sync;
-
 	host->mmc_host_ops.get_ro = mmc_gpio_get_ro;
 	host->mmc_host_ops.start_signal_voltage_switch =
 					sdhci_omap_start_signal_voltage_switch;
 	host->mmc_host_ops.set_ios = sdhci_omap_set_ios;
 	host->mmc_host_ops.card_busy = sdhci_omap_card_busy;
 	host->mmc_host_ops.execute_tuning = sdhci_omap_execute_tuning;
+	host->mmc_host_ops.enable_sdio_irq = sdhci_omap_enable_sdio_irq;
 
-	sdhci_read_caps(host);
-	host->caps |= SDHCI_CAN_DO_ADMA2;
-
-	ret = sdhci_add_host(host);
+	ret = sdhci_setup_host(host);
 	if (ret)
 		goto err_put_sync;
 
+	ret = sdhci_omap_config_iodelay_pinctrl_state(omap_host);
+	if (ret)
+		goto err_cleanup_host;
+
+	ret = __sdhci_add_host(host);
+	if (ret)
+		goto err_cleanup_host;
+
 	return 0;
 
+err_cleanup_host:
+	sdhci_cleanup_host(host);
+
 err_put_sync:
 	pm_runtime_put_sync(dev);
 

drivers/mmc/host/sdhci.c

@@ -709,29 +709,16 @@ static u32 sdhci_sdma_address(struct sdhci_host *host)
 		return sg_dma_address(host->data->sg);
 }
 
-static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd)
+static unsigned int sdhci_target_timeout(struct sdhci_host *host,
+					 struct mmc_command *cmd,
+					 struct mmc_data *data)
 {
-	u8 count;
-	struct mmc_data *data = cmd->data;
-	unsigned target_timeout, current_timeout;
-
-	/*
-	 * If the host controller provides us with an incorrect timeout
-	 * value, just skip the check and use 0xE.  The hardware may take
-	 * longer to time out, but that's much better than having a too-short
-	 * timeout value.
-	 */
-	if (host->quirks & SDHCI_QUIRK_BROKEN_TIMEOUT_VAL)
-		return 0xE;
-
-	/* Unspecified timeout, assume max */
-	if (!data && !cmd->busy_timeout)
-		return 0xE;
+	unsigned int target_timeout;
 
 	/* timeout in us */
-	if (!data)
+	if (!data) {
 		target_timeout = cmd->busy_timeout * 1000;
-	else {
+	} else {
 		target_timeout = DIV_ROUND_UP(data->timeout_ns, 1000);
 		if (host->clock && data->timeout_clks) {
 			unsigned long long val;
@@ -748,6 +735,67 @@ static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd)
 		}
 	}
 
+	return target_timeout;
+}
+
+static void sdhci_calc_sw_timeout(struct sdhci_host *host,
+				  struct mmc_command *cmd)
+{
+	struct mmc_data *data = cmd->data;
+	struct mmc_host *mmc = host->mmc;
+	struct mmc_ios *ios = &mmc->ios;
+	unsigned char bus_width = 1 << ios->bus_width;
+	unsigned int blksz;
+	unsigned int freq;
+	u64 target_timeout;
+	u64 transfer_time;
+
+	target_timeout = sdhci_target_timeout(host, cmd, data);
+	target_timeout *= NSEC_PER_USEC;
+
+	if (data) {
+		blksz = data->blksz;
+		freq = host->mmc->actual_clock ? : host->clock;
+		transfer_time = (u64)blksz * NSEC_PER_SEC * (8 / bus_width);
+		do_div(transfer_time, freq);
+		/* multiply by '2' to account for any unknowns */
+		transfer_time = transfer_time * 2;
+		/* calculate timeout for the entire data */
+		host->data_timeout = data->blocks * target_timeout +
+				     transfer_time;
+	} else {
+		host->data_timeout = target_timeout;
+	}
+
+	if (host->data_timeout)
+		host->data_timeout += MMC_CMD_TRANSFER_TIME;
+}
+
+static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd,
+			     bool *too_big)
+{
+	u8 count;
+	struct mmc_data *data = cmd->data;
+	unsigned target_timeout, current_timeout;
+
+	*too_big = true;
+
+	/*
+	 * If the host controller provides us with an incorrect timeout
+	 * value, just skip the check and use 0xE.  The hardware may take
+	 * longer to time out, but that's much better than having a too-short
+	 * timeout value.
+	 */
+	if (host->quirks & SDHCI_QUIRK_BROKEN_TIMEOUT_VAL)
+		return 0xE;
+
+	/* Unspecified timeout, assume max */
+	if (!data && !cmd->busy_timeout)
+		return 0xE;
+
+	/* timeout in us */
+	target_timeout = sdhci_target_timeout(host, cmd, data);
+
 	/*
 	 * Figure out needed cycles.
 	 * We do this in steps in order to fit inside a 32 bit int.
@@ -768,9 +816,12 @@ static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd)
 	}
 
 	if (count >= 0xF) {
+		if (!(host->quirks2 & SDHCI_QUIRK2_DISABLE_HW_TIMEOUT))
 			DBG("Too large timeout 0x%x requested for CMD%d!\n",
 			    count, cmd->opcode);
 		count = 0xE;
+	} else {
+		*too_big = false;
 	}
 
 	return count;
@@ -790,6 +841,16 @@ static void sdhci_set_transfer_irqs(struct sdhci_host *host)
 	sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
 }
 
+static void sdhci_set_data_timeout_irq(struct sdhci_host *host, bool enable)
+{
+	if (enable)
+		host->ier |= SDHCI_INT_DATA_TIMEOUT;
+	else
+		host->ier &= ~SDHCI_INT_DATA_TIMEOUT;
+	sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
+	sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
+}
+
 static void sdhci_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
 {
 	u8 count;
@@ -797,7 +858,18 @@ static void sdhci_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
 	if (host->ops->set_timeout) {
 		host->ops->set_timeout(host, cmd);
 	} else {
-		count = sdhci_calc_timeout(host, cmd);
+		bool too_big = false;
+
+		count = sdhci_calc_timeout(host, cmd, &too_big);
+
+		if (too_big &&
+		    host->quirks2 & SDHCI_QUIRK2_DISABLE_HW_TIMEOUT) {
+			sdhci_calc_sw_timeout(host, cmd);
+			sdhci_set_data_timeout_irq(host, false);
+		} else if (!(host->ier & SDHCI_INT_DATA_TIMEOUT)) {
+			sdhci_set_data_timeout_irq(host, true);
+		}
+
 		sdhci_writeb(host, count, SDHCI_TIMEOUT_CONTROL);
 	}
 }
@@ -807,6 +879,8 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_command *cmd)
 	u8 ctrl;
 	struct mmc_data *data = cmd->data;
 
+	host->data_timeout = 0;
+
 	if (sdhci_data_line_cmd(cmd))
 		sdhci_set_timeout(host, cmd);
 
@@ -1160,13 +1234,6 @@ void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
 		mdelay(1);
 	}
 
-	timeout = jiffies;
-	if (!cmd->data && cmd->busy_timeout > 9000)
-		timeout += DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ;
-	else
-		timeout += 10 * HZ;
-	sdhci_mod_timer(host, cmd->mrq, timeout);
-
 	host->cmd = cmd;
 	if (sdhci_data_line_cmd(cmd)) {
 		WARN_ON(host->data_cmd);
@@ -1206,6 +1273,15 @@ void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
 	    cmd->opcode == MMC_SEND_TUNING_BLOCK_HS200)
 		flags |= SDHCI_CMD_DATA;
 
+	timeout = jiffies;
+	if (host->data_timeout)
+		timeout += nsecs_to_jiffies(host->data_timeout);
+	else if (!cmd->data && cmd->busy_timeout > 9000)
+		timeout += DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ;
+	else
+		timeout += 10 * HZ;
+	sdhci_mod_timer(host, cmd->mrq, timeout);
+
 	sdhci_writew(host, SDHCI_MAKE_CMD(cmd->opcode, flags), SDHCI_COMMAND);
 }
 EXPORT_SYMBOL_GPL(sdhci_send_command);
@@ -3616,6 +3692,10 @@ int sdhci_setup_host(struct sdhci_host *host)
 		mmc->max_busy_timeout /= host->timeout_clk;
 	}
 
+	if (host->quirks2 & SDHCI_QUIRK2_DISABLE_HW_TIMEOUT &&
+	    !host->ops->get_max_timeout_count)
+		mmc->max_busy_timeout = 0;
+
 	mmc->caps |= MMC_CAP_SDIO_IRQ | MMC_CAP_ERASE | MMC_CAP_CMD23;
 	mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD;
 
@@ -3672,6 +3752,16 @@ int sdhci_setup_host(struct sdhci_host *host)
 	if (host->quirks2 & SDHCI_QUIRK2_NO_1_8_V) {
 		host->caps1 &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
 				 SDHCI_SUPPORT_DDR50);
+		/*
+		 * The SDHCI controller in a SoC might support HS200/HS400
+		 * (indicated using mmc-hs200-1_8v/mmc-hs400-1_8v dt property),
+		 * but if the board is modeled such that the IO lines are not
+		 * connected to 1.8v then HS200/HS400 cannot be supported.
+		 * Disable HS200/HS400 if the board does not have 1.8v connected
+		 * to the IO lines. (Applicable for other modes in 1.8v)
+		 */
+		mmc->caps2 &= ~(MMC_CAP2_HSX00_1_8V | MMC_CAP2_HS400_ES);
+		mmc->caps &= ~(MMC_CAP_1_8V_DDR | MMC_CAP_UHS);
 	}
 
 	/* Any UHS-I mode in caps implies SDR12 and SDR25 support. */

drivers/mmc/host/sdhci.h

@@ -332,6 +332,14 @@ struct sdhci_adma2_64_desc {
 /* Allow for a a command request and a data request at the same time */
 #define SDHCI_MAX_MRQS		2
 
+/*
+ * 48bit command and 136 bit response in 100KHz clock could take upto 2.48ms.
+ * However since the start time of the command, the time between
+ * command and response, and the time between response and start of data is
+ * not known, set the command transfer time to 10ms.
+ */
+#define MMC_CMD_TRANSFER_TIME	(10 * NSEC_PER_MSEC) /* max 10 ms */
+
 enum sdhci_cookie {
 	COOKIE_UNMAPPED,
 	COOKIE_PRE_MAPPED,	/* mapped by sdhci_pre_req() */
@@ -437,6 +445,11 @@ struct sdhci_host {
 #define SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN		(1<<15)
 /* Controller has CRC in 136 bit Command Response */
 #define SDHCI_QUIRK2_RSP_136_HAS_CRC			(1<<16)
+/*
+ * Disable HW timeout if the requested timeout is more than the maximum
+ * obtainable timeout.
+ */
+#define SDHCI_QUIRK2_DISABLE_HW_TIMEOUT			(1<<17)
 
 	int irq;		/* Device IRQ */
 	void __iomem *ioaddr;	/* Mapped address */
@@ -550,6 +563,8 @@ struct sdhci_host {
 	/* Host SDMA buffer boundary. */
 	u32			sdma_boundary;
 
+	u64			data_timeout;
+
 	unsigned long private[0] ____cacheline_aligned;
 };
 

include/linux/mmc/host.h

@@ -320,6 +320,9 @@ struct mmc_host {
 #define MMC_CAP_UHS_SDR50	(1 << 18)	/* Host supports UHS SDR50 mode */
 #define MMC_CAP_UHS_SDR104	(1 << 19)	/* Host supports UHS SDR104 mode */
 #define MMC_CAP_UHS_DDR50	(1 << 20)	/* Host supports UHS DDR50 mode */
+#define MMC_CAP_UHS		(MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 | \
+				 MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | \
+				 MMC_CAP_UHS_DDR50)
 /* (1 << 21) is free for reuse */
 #define MMC_CAP_DRIVER_TYPE_A	(1 << 23)	/* Host supports Driver Type A */
 #define MMC_CAP_DRIVER_TYPE_C	(1 << 24)	/* Host supports Driver Type C */
@@ -345,6 +348,7 @@ struct mmc_host {
 #define MMC_CAP2_HS400_1_2V	(1 << 16)	/* Can support HS400 1.2V */
 #define MMC_CAP2_HS400		(MMC_CAP2_HS400_1_8V | \
 				 MMC_CAP2_HS400_1_2V)
+#define MMC_CAP2_HSX00_1_8V	(MMC_CAP2_HS200_1_8V_SDR | MMC_CAP2_HS400_1_8V)
 #define MMC_CAP2_HSX00_1_2V	(MMC_CAP2_HS200_1_2V_SDR | MMC_CAP2_HS400_1_2V)
 #define MMC_CAP2_SDIO_IRQ_NOTHREAD (1 << 17)
 #define MMC_CAP2_NO_WRITE_PROTECT (1 << 18)	/* No physical write protect pin, assume that card is always read-write */