e1000e: convert calls of ops.[read|write]_reg to e1e_[r|w]phy

Cleans up the code a bit by using the driver-specific e1e_rphy and
e1e_wphy macros instead of the full function pointer variants.  Fix
a couple whitespace issue with two already existing calls to e1e_wphy.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/e1000e/ich8lan.c

@@ -3118,7 +3118,7 @@ static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw)
 	 * Reset the phy after disabling host wakeup to reset the Rx buffer.
 	 */
 	if (hw->phy.type == e1000_phy_82578) {
-		hw->phy.ops.read_reg(hw, BM_WUC, &i);
+		e1e_rphy(hw, BM_WUC, &i);
 		ret_val = e1000_phy_hw_reset_ich8lan(hw);
 		if (ret_val)
 			return ret_val;
@@ -3276,8 +3276,7 @@ static s32 e1000_setup_link_ich8lan(struct e1000_hw *hw)
 	    (hw->phy.type == e1000_phy_82577)) {
 		ew32(FCRTV_PCH, hw->fc.refresh_time);
 
-		ret_val = hw->phy.ops.write_reg(hw,
-		                             PHY_REG(BM_PORT_CTRL_PAGE, 27),
+		ret_val = e1e_wphy(hw, PHY_REG(BM_PORT_CTRL_PAGE, 27),
 				   hw->fc.pause_time);
 		if (ret_val)
 			return ret_val;
@@ -3342,8 +3341,7 @@ static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw)
 			return ret_val;
 		break;
 	case e1000_phy_ife:
-		ret_val = hw->phy.ops.read_reg(hw, IFE_PHY_MDIX_CONTROL,
-		                               &reg_data);
+		ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, &reg_data);
 		if (ret_val)
 			return ret_val;
 
@@ -3361,8 +3359,7 @@ static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw)
 			reg_data |= IFE_PMC_AUTO_MDIX;
 			break;
 		}
-		ret_val = hw->phy.ops.write_reg(hw, IFE_PHY_MDIX_CONTROL,
-		                                reg_data);
+		ret_val = e1e_wphy(hw, IFE_PHY_MDIX_CONTROL, reg_data);
 		if (ret_val)
 			return ret_val;
 		break;
@@ -3646,7 +3643,8 @@ static s32 e1000_led_off_ich8lan(struct e1000_hw *hw)
 {
 	if (hw->phy.type == e1000_phy_ife)
 		return e1e_wphy(hw, IFE_PHY_SPECIAL_CONTROL_LED,
-			       (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF));
+				(IFE_PSCL_PROBE_MODE |
+				 IFE_PSCL_PROBE_LEDS_OFF));
 
 	ew32(LEDCTL, hw->mac.ledctl_mode1);
 	return 0;
@@ -3660,8 +3658,7 @@ static s32 e1000_led_off_ich8lan(struct e1000_hw *hw)
  **/
 static s32 e1000_setup_led_pchlan(struct e1000_hw *hw)
 {
-	return hw->phy.ops.write_reg(hw, HV_LED_CONFIG,
-					(u16)hw->mac.ledctl_mode1);
+	return e1e_wphy(hw, HV_LED_CONFIG, (u16)hw->mac.ledctl_mode1);
 }
 
 /**
@@ -3672,8 +3669,7 @@ static s32 e1000_setup_led_pchlan(struct e1000_hw *hw)
  **/
 static s32 e1000_cleanup_led_pchlan(struct e1000_hw *hw)
 {
-	return hw->phy.ops.write_reg(hw, HV_LED_CONFIG,
-					(u16)hw->mac.ledctl_default);
+	return e1e_wphy(hw, HV_LED_CONFIG, (u16)hw->mac.ledctl_default);
 }
 
 /**
@@ -3704,7 +3700,7 @@ static s32 e1000_led_on_pchlan(struct e1000_hw *hw)
 		}
 	}
 
-	return hw->phy.ops.write_reg(hw, HV_LED_CONFIG, data);
+	return e1e_wphy(hw, HV_LED_CONFIG, data);
 }
 
 /**
@@ -3735,7 +3731,7 @@ static s32 e1000_led_off_pchlan(struct e1000_hw *hw)
 		}
 	}
 
-	return hw->phy.ops.write_reg(hw, HV_LED_CONFIG, data);
+	return e1e_wphy(hw, HV_LED_CONFIG, data);
 }
 
 /**
@@ -3844,20 +3840,20 @@ static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw)
 	if ((hw->phy.type == e1000_phy_82578) ||
 	    (hw->phy.type == e1000_phy_82579) ||
 	    (hw->phy.type == e1000_phy_82577)) {
-		hw->phy.ops.read_reg(hw, HV_SCC_UPPER, &phy_data);
-		hw->phy.ops.read_reg(hw, HV_SCC_LOWER, &phy_data);
-		hw->phy.ops.read_reg(hw, HV_ECOL_UPPER, &phy_data);
-		hw->phy.ops.read_reg(hw, HV_ECOL_LOWER, &phy_data);
-		hw->phy.ops.read_reg(hw, HV_MCC_UPPER, &phy_data);
-		hw->phy.ops.read_reg(hw, HV_MCC_LOWER, &phy_data);
-		hw->phy.ops.read_reg(hw, HV_LATECOL_UPPER, &phy_data);
-		hw->phy.ops.read_reg(hw, HV_LATECOL_LOWER, &phy_data);
-		hw->phy.ops.read_reg(hw, HV_COLC_UPPER, &phy_data);
-		hw->phy.ops.read_reg(hw, HV_COLC_LOWER, &phy_data);
-		hw->phy.ops.read_reg(hw, HV_DC_UPPER, &phy_data);
-		hw->phy.ops.read_reg(hw, HV_DC_LOWER, &phy_data);
-		hw->phy.ops.read_reg(hw, HV_TNCRS_UPPER, &phy_data);
-		hw->phy.ops.read_reg(hw, HV_TNCRS_LOWER, &phy_data);
+		e1e_rphy(hw, HV_SCC_UPPER, &phy_data);
+		e1e_rphy(hw, HV_SCC_LOWER, &phy_data);
+		e1e_rphy(hw, HV_ECOL_UPPER, &phy_data);
+		e1e_rphy(hw, HV_ECOL_LOWER, &phy_data);
+		e1e_rphy(hw, HV_MCC_UPPER, &phy_data);
+		e1e_rphy(hw, HV_MCC_LOWER, &phy_data);
+		e1e_rphy(hw, HV_LATECOL_UPPER, &phy_data);
+		e1e_rphy(hw, HV_LATECOL_LOWER, &phy_data);
+		e1e_rphy(hw, HV_COLC_UPPER, &phy_data);
+		e1e_rphy(hw, HV_COLC_LOWER, &phy_data);
+		e1e_rphy(hw, HV_DC_UPPER, &phy_data);
+		e1e_rphy(hw, HV_DC_LOWER, &phy_data);
+		e1e_rphy(hw, HV_TNCRS_UPPER, &phy_data);
+		e1e_rphy(hw, HV_TNCRS_LOWER, &phy_data);
 	}
 }
 

drivers/net/e1000e/lib.c

@@ -1135,7 +1135,8 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		ret_val = e1e_rphy(hw, PHY_AUTONEG_ADV, &mii_nway_adv_reg);
 		if (ret_val)
 			return ret_val;
-		ret_val = e1e_rphy(hw, PHY_LP_ABILITY, &mii_nway_lp_ability_reg);
+		ret_val =
+		    e1e_rphy(hw, PHY_LP_ABILITY, &mii_nway_lp_ability_reg);
 		if (ret_val)
 			return ret_val;
 

drivers/net/e1000e/phy.c

@@ -637,12 +637,11 @@ s32 e1000e_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data)
  **/
 s32 e1000_copper_link_setup_82577(struct e1000_hw *hw)
 {
-	struct e1000_phy_info *phy = &hw->phy;
 	s32 ret_val;
 	u16 phy_data;
 
 	/* Enable CRS on TX. This must be set for half-duplex operation. */
-	ret_val = phy->ops.read_reg(hw, I82577_CFG_REG, &phy_data);
+	ret_val = e1e_rphy(hw, I82577_CFG_REG, &phy_data);
 	if (ret_val)
 		goto out;
 
@@ -651,7 +650,7 @@ s32 e1000_copper_link_setup_82577(struct e1000_hw *hw)
 	/* Enable downshift */
 	phy_data |= I82577_CFG_ENABLE_DOWNSHIFT;
 
-	ret_val = phy->ops.write_reg(hw, I82577_CFG_REG, phy_data);
+	ret_val = e1e_wphy(hw, I82577_CFG_REG, phy_data);
 
 out:
 	return ret_val;
@@ -774,16 +773,14 @@ s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw)
 	}
 
 	if (phy->type == e1000_phy_82578) {
-		ret_val = phy->ops.read_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
-		                            &phy_data);
+		ret_val = e1e_rphy(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
 		if (ret_val)
 			return ret_val;
 
 		/* 82578 PHY - set the downshift count to 1x. */
 		phy_data |= I82578_EPSCR_DOWNSHIFT_ENABLE;
 		phy_data &= ~I82578_EPSCR_DOWNSHIFT_COUNTER_MASK;
-		ret_val = phy->ops.write_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
-		                             phy_data);
+		ret_val = e1e_wphy(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
 		if (ret_val)
 			return ret_val;
 	}
@@ -1319,8 +1316,7 @@ s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw)
 				 * We didn't get link.
 				 * Reset the DSP and cross our fingers.
 				 */
-				ret_val = e1e_wphy(hw,
-						M88E1000_PHY_PAGE_SELECT,
+				ret_val = e1e_wphy(hw, M88E1000_PHY_PAGE_SELECT,
 						   0x001d);
 				if (ret_val)
 					return ret_val;
@@ -3071,12 +3067,12 @@ s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw)
 		goto out;
 
 	/* Do not apply workaround if in PHY loopback bit 14 set */
-	hw->phy.ops.read_reg(hw, PHY_CONTROL, &data);
+	e1e_rphy(hw, PHY_CONTROL, &data);
 	if (data & PHY_CONTROL_LB)
 		goto out;
 
 	/* check if link is up and at 1Gbps */
-	ret_val = hw->phy.ops.read_reg(hw, BM_CS_STATUS, &data);
+	ret_val = e1e_rphy(hw, BM_CS_STATUS, &data);
 	if (ret_val)
 		goto out;
 
@@ -3092,14 +3088,12 @@ s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw)
 	mdelay(200);
 
 	/* flush the packets in the fifo buffer */
-	ret_val = hw->phy.ops.write_reg(hw, HV_MUX_DATA_CTRL,
-	                                HV_MUX_DATA_CTRL_GEN_TO_MAC |
+	ret_val = e1e_wphy(hw, HV_MUX_DATA_CTRL, HV_MUX_DATA_CTRL_GEN_TO_MAC |
 			   HV_MUX_DATA_CTRL_FORCE_SPEED);
 	if (ret_val)
 		goto out;
 
-	ret_val = hw->phy.ops.write_reg(hw, HV_MUX_DATA_CTRL,
-	                                HV_MUX_DATA_CTRL_GEN_TO_MAC);
+	ret_val = e1e_wphy(hw, HV_MUX_DATA_CTRL, HV_MUX_DATA_CTRL_GEN_TO_MAC);
 
 out:
 	return ret_val;
@@ -3119,7 +3113,7 @@ s32 e1000_check_polarity_82577(struct e1000_hw *hw)
 	s32 ret_val;
 	u16 data;
 
-	ret_val = phy->ops.read_reg(hw, I82577_PHY_STATUS_2, &data);
+	ret_val = e1e_rphy(hw, I82577_PHY_STATUS_2, &data);
 
 	if (!ret_val)
 		phy->cable_polarity = (data & I82577_PHY_STATUS2_REV_POLARITY)
@@ -3142,13 +3136,13 @@ s32 e1000_phy_force_speed_duplex_82577(struct e1000_hw *hw)
 	u16 phy_data;
 	bool link;
 
-	ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_data);
+	ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
 	if (ret_val)
 		goto out;
 
 	e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
 
-	ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_data);
+	ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
 	if (ret_val)
 		goto out;
 
@@ -3212,7 +3206,7 @@ s32 e1000_get_phy_info_82577(struct e1000_hw *hw)
 	if (ret_val)
 		goto out;
 
-	ret_val = phy->ops.read_reg(hw, I82577_PHY_STATUS_2, &data);
+	ret_val = e1e_rphy(hw, I82577_PHY_STATUS_2, &data);
 	if (ret_val)
 		goto out;
 
@@ -3224,7 +3218,7 @@ s32 e1000_get_phy_info_82577(struct e1000_hw *hw)
 		if (ret_val)
 			goto out;
 
-		ret_val = phy->ops.read_reg(hw, PHY_1000T_STATUS, &data);
+		ret_val = e1e_rphy(hw, PHY_1000T_STATUS, &data);
 		if (ret_val)
 			goto out;
 
@@ -3258,7 +3252,7 @@ s32 e1000_get_cable_length_82577(struct e1000_hw *hw)
 	s32 ret_val;
 	u16 phy_data, length;
 
-	ret_val = phy->ops.read_reg(hw, I82577_PHY_DIAG_STATUS, &phy_data);
+	ret_val = e1e_rphy(hw, I82577_PHY_DIAG_STATUS, &phy_data);
 	if (ret_val)
 		goto out;