net: Micrel KS8851 SPI network driver

Network driver for the SPI version of the Micrel KS8851
network chip.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/Kconfig

@@ -1729,6 +1729,12 @@ config KS8842
 	help
 	  This platform driver is for Micrel KSZ8842 chip.
 
+config KS8851
+       tristate "Micrel KS8851 SPI"
+       depends on SPI
+       help
+         SPI driver for Micrel KS8851 SPI attached network chip.
+
 config VIA_RHINE
 	tristate "VIA Rhine support"
 	depends on NET_PCI && PCI

drivers/net/Makefile

@@ -88,6 +88,7 @@ obj-$(CONFIG_SKGE) += skge.o
 obj-$(CONFIG_SKY2) += sky2.o
 obj-$(CONFIG_SKFP) += skfp/
 obj-$(CONFIG_KS8842)	+= ks8842.o
+obj-$(CONFIG_KS8851)	+= ks8851.o
 obj-$(CONFIG_VIA_RHINE) += via-rhine.o
 obj-$(CONFIG_VIA_VELOCITY) += via-velocity.o
 obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o

drivers/net/ks8851.c

+/* drivers/net/ks8651.c
+ *
+ * Copyright 2009 Simtec Electronics
+ *	http://www.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#define DEBUG
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/cache.h>
+#include <linux/crc32.h>
+#include <linux/mii.h>
+
+#include <linux/spi/spi.h>
+
+#include "ks8851.h"
+
+/**
+ * struct ks8851_rxctrl - KS8851 driver rx control
+ * @mchash: Multicast hash-table data.
+ * @rxcr1: KS_RXCR1 register setting
+ * @rxcr2: KS_RXCR2 register setting
+ *
+ * Representation of the settings needs to control the receive filtering
+ * such as the multicast hash-filter and the receive register settings. This
+ * is used to make the job of working out if the receive settings change and
+ * then issuing the new settings to the worker that will send the necessary
+ * commands.
+ */
+struct ks8851_rxctrl {
+	u16	mchash[4];
+	u16	rxcr1;
+	u16	rxcr2;
+};
+
+/**
+ * union ks8851_tx_hdr - tx header data
+ * @txb: The header as bytes
+ * @txw: The header as 16bit, little-endian words
+ *
+ * A dual representation of the tx header data to allow
+ * access to individual bytes, and to allow 16bit accesses
+ * with 16bit alignment.
+ */
+union ks8851_tx_hdr {
+	u8	txb[6];
+	__le16	txw[3];
+};
+
+/**
+ * struct ks8851_net - KS8851 driver private data
+ * @netdev: The network device we're bound to
+ * @spidev: The spi device we're bound to.
+ * @lock: Lock to ensure that the device is not accessed when busy.
+ * @statelock: Lock on this structure for tx list.
+ * @mii: The MII state information for the mii calls.
+ * @rxctrl: RX settings for @rxctrl_work.
+ * @tx_work: Work queue for tx packets
+ * @irq_work: Work queue for servicing interrupts
+ * @rxctrl_work: Work queue for updating RX mode and multicast lists
+ * @txq: Queue of packets for transmission.
+ * @spi_msg1: pre-setup SPI transfer with one message, @spi_xfer1.
+ * @spi_msg2: pre-setup SPI transfer with two messages, @spi_xfer2.
+ * @txh: Space for generating packet TX header in DMA-able data
+ * @rxd: Space for receiving SPI data, in DMA-able space.
+ * @txd: Space for transmitting SPI data, in DMA-able space.
+ * @msg_enable: The message flags controlling driver output (see ethtool).
+ * @fid: Incrementing frame id tag.
+ * @rc_ier: Cached copy of KS_IER.
+ * @rc_rxqcr: Cached copy of KS_RXQCR.
+ *
+ * The @lock ensures that the chip is protected when certain operations are
+ * in progress. When the read or write packet transfer is in progress, most
+ * of the chip registers are not ccessible until the transfer is finished and
+ * the DMA has been de-asserted.
+ *
+ * The @statelock is used to protect information in the structure which may
+ * need to be accessed via several sources, such as the network driver layer
+ * or one of the work queues.
+ *
+ * We align the buffers we may use for rx/tx to ensure that if the SPI driver
+ * wants to DMA map them, it will not have any problems with data the driver
+ * modifies.
+ */
+struct ks8851_net {
+	struct net_device	*netdev;
+	struct spi_device	*spidev;
+	struct mutex		lock;
+	spinlock_t		statelock;
+
+	union ks8851_tx_hdr	txh ____cacheline_aligned;
+	u8			rxd[8];
+	u8			txd[8];
+
+	u32			msg_enable ____cacheline_aligned;
+	u16			tx_space;
+	u8			fid;
+
+	u16			rc_ier;
+	u16			rc_rxqcr;
+
+	struct mii_if_info	mii;
+	struct ks8851_rxctrl	rxctrl;
+
+	struct work_struct	tx_work;
+	struct work_struct	irq_work;
+	struct work_struct	rxctrl_work;
+
+	struct sk_buff_head	txq;
+
+	struct spi_message	spi_msg1;
+	struct spi_message	spi_msg2;
+	struct spi_transfer	spi_xfer1;
+	struct spi_transfer	spi_xfer2[2];
+};
+
+static int msg_enable;
+
+#define ks_info(_ks, _msg...) dev_info(&(_ks)->spidev->dev, _msg)
+#define ks_warn(_ks, _msg...) dev_warn(&(_ks)->spidev->dev, _msg)
+#define ks_dbg(_ks, _msg...) dev_dbg(&(_ks)->spidev->dev, _msg)
+#define ks_err(_ks, _msg...) dev_err(&(_ks)->spidev->dev, _msg)
+
+/* shift for byte-enable data */
+#define BYTE_EN(_x)	((_x) << 2)
+
+/* turn register number and byte-enable mask into data for start of packet */
+#define MK_OP(_byteen, _reg) (BYTE_EN(_byteen) | (_reg)  << (8+2) | (_reg) >> 6)
+
+/* SPI register read/write calls.
+ *
+ * All these calls issue SPI transactions to access the chip's registers. They
+ * all require that the necessary lock is held to prevent accesses when the
+ * chip is busy transfering packet data (RX/TX FIFO accesses).
+ */
+
+/**
+ * ks8851_wrreg16 - write 16bit register value to chip
+ * @ks: The chip state
+ * @reg: The register address
+ * @val: The value to write
+ *
+ * Issue a write to put the value @val into the register specified in @reg.
+ */
+static void ks8851_wrreg16(struct ks8851_net *ks, unsigned reg, unsigned val)
+{
+	struct spi_transfer *xfer = &ks->spi_xfer1;
+	struct spi_message *msg = &ks->spi_msg1;
+	__le16 txb[2];
+	int ret;
+
+	txb[0] = cpu_to_le16(MK_OP(reg & 2 ? 0xC : 0x03, reg) | KS_SPIOP_WR);
+	txb[1] = cpu_to_le16(val);
+
+	xfer->tx_buf = txb;
+	xfer->rx_buf = NULL;
+	xfer->len = 4;
+
+	ret = spi_sync(ks->spidev, msg);
+	if (ret < 0)
+		ks_err(ks, "spi_sync() failed\n");
+}
+
+/**
+ * ks8851_rx_1msg - select whether to use one or two messages for spi read
+ * @ks: The device structure
+ *
+ * Return whether to generate a single message with a tx and rx buffer
+ * supplied to spi_sync(), or alternatively send the tx and rx buffers
+ * as separate messages.
+ *
+ * Depending on the hardware in use, a single message may be more efficient
+ * on interrupts or work done by the driver.
+ *
+ * This currently always returns true until we add some per-device data passed
+ * from the platform code to specify which mode is better.
+ */
+static inline bool ks8851_rx_1msg(struct ks8851_net *ks)
+{
+	return true;
+}
+
+/**
+ * ks8851_rdreg - issue read register command and return the data
+ * @ks: The device state
+ * @op: The register address and byte enables in message format.
+ * @rxb: The RX buffer to return the result into
+ * @rxl: The length of data expected.
+ *
+ * This is the low level read call that issues the necessary spi message(s)
+ * to read data from the register specified in @op.
+ */
+static void ks8851_rdreg(struct ks8851_net *ks, unsigned op,
+			 u8 *rxb, unsigned rxl)
+{
+	struct spi_transfer *xfer;
+	struct spi_message *msg;
+	__le16 *txb = (__le16 *)ks->txd;
+	u8 *trx = ks->rxd;
+	int ret;
+
+	txb[0] = cpu_to_le16(op | KS_SPIOP_RD);
+
+	if (ks8851_rx_1msg(ks)) {
+		msg = &ks->spi_msg1;
+		xfer = &ks->spi_xfer1;
+
+		xfer->tx_buf = txb;
+		xfer->rx_buf = trx;
+		xfer->len = rxl + 2;
+	} else {
+		msg = &ks->spi_msg2;
+		xfer = ks->spi_xfer2;
+
+		xfer->tx_buf = txb;
+		xfer->rx_buf = NULL;
+		xfer->len = 2;
+
+		xfer++;
+		xfer->tx_buf = NULL;
+		xfer->rx_buf = trx;
+		xfer->len = rxl;
+	}
+
+	ret = spi_sync(ks->spidev, msg);
+	if (ret < 0)
+		ks_err(ks, "read: spi_sync() failed\n");
+	else if (ks8851_rx_1msg(ks))
+		memcpy(rxb, trx + 2, rxl);
+	else
+		memcpy(rxb, trx, rxl);
+}
+
+/**
+ * ks8851_rdreg8 - read 8 bit register from device
+ * @ks: The chip information
+ * @reg: The register address
+ *
+ * Read a 8bit register from the chip, returning the result
+*/
+static unsigned ks8851_rdreg8(struct ks8851_net *ks, unsigned reg)
+{
+	u8 rxb[1];
+
+	ks8851_rdreg(ks, MK_OP(1 << (reg & 3), reg), rxb, 1);
+	return rxb[0];
+}
+
+/**
+ * ks8851_rdreg16 - read 16 bit register from device
+ * @ks: The chip information
+ * @reg: The register address
+ *
+ * Read a 16bit register from the chip, returning the result
+*/
+static unsigned ks8851_rdreg16(struct ks8851_net *ks, unsigned reg)
+{
+	__le16 rx = 0;
+
+	ks8851_rdreg(ks, MK_OP(reg & 2 ? 0xC : 0x3, reg), (u8 *)&rx, 2);
+	return le16_to_cpu(rx);
+}
+
+/**
+ * ks8851_rdreg32 - read 32 bit register from device
+ * @ks: The chip information
+ * @reg: The register address
+ *
+ * Read a 32bit register from the chip.
+ *
+ * Note, this read requires the address be aligned to 4 bytes.
+*/
+static unsigned ks8851_rdreg32(struct ks8851_net *ks, unsigned reg)
+{
+	__le32 rx = 0;
+
+	WARN_ON(reg & 3);
+
+	ks8851_rdreg(ks, MK_OP(0xf, reg), (u8 *)&rx, 4);
+	return le32_to_cpu(rx);
+}
+
+/**
+ * ks8851_soft_reset - issue one of the soft reset to the device
+ * @ks: The device state.
+ * @op: The bit(s) to set in the GRR
+ *
+ * Issue the relevant soft-reset command to the device's GRR register
+ * specified by @op.
+ *
+ * Note, the delays are in there as a caution to ensure that the reset
+ * has time to take effect and then complete. Since the datasheet does
+ * not currently specify the exact sequence, we have chosen something
+ * that seems to work with our device.
+ */
+static void ks8851_soft_reset(struct ks8851_net *ks, unsigned op)
+{
+	ks8851_wrreg16(ks, KS_GRR, op);
+	mdelay(1);	/* wait a short time to effect reset */
+	ks8851_wrreg16(ks, KS_GRR, 0);
+	mdelay(1);	/* wait for condition to clear */
+}
+
+/**
+ * ks8851_write_mac_addr - write mac address to device registers
+ * @dev: The network device
+ *
+ * Update the KS8851 MAC address registers from the address in @dev.
+ *
+ * This call assumes that the chip is not running, so there is no need to
+ * shutdown the RXQ process whilst setting this.
+*/
+static int ks8851_write_mac_addr(struct net_device *dev)
+{
+	struct ks8851_net *ks = netdev_priv(dev);
+	u16 *mcp = (u16 *)dev->dev_addr;
+
+	mutex_lock(&ks->lock);
+
+	ks8851_wrreg16(ks, KS_MARL, mcp[0]);
+	ks8851_wrreg16(ks, KS_MARM, mcp[1]);
+	ks8851_wrreg16(ks, KS_MARH, mcp[2]);
+
+	mutex_unlock(&ks->lock);
+
+	return 0;
+}
+
+/**
+ * ks8851_init_mac - initialise the mac address
+ * @ks: The device structure
+ *
+ * Get or create the initial mac address for the device and then set that
+ * into the station address register. Currently we assume that the device
+ * does not have a valid mac address in it, and so we use random_ether_addr()
+ * to create a new one.
+ *
+ * In future, the driver should check to see if the device has an EEPROM
+ * attached and whether that has a valid ethernet address in it.
+ */
+static void ks8851_init_mac(struct ks8851_net *ks)
+{
+	struct net_device *dev = ks->netdev;
+
+	random_ether_addr(dev->dev_addr);
+	ks8851_write_mac_addr(dev);
+}
+
+/**
+ * ks8851_irq - device interrupt handler
+ * @irq: Interrupt number passed from the IRQ hnalder.
+ * @pw: The private word passed to register_irq(), our struct ks8851_net.
+ *
+ * Disable the interrupt from happening again until we've processed the
+ * current status by scheduling ks8851_irq_work().
+ */
+static irqreturn_t ks8851_irq(int irq, void *pw)
+{
+	struct ks8851_net *ks = pw;
+
+	disable_irq_nosync(irq);
+	schedule_work(&ks->irq_work);
+	return IRQ_HANDLED;
+}
+
+/**
+ * ks8851_rdfifo - read data from the receive fifo
+ * @ks: The device state.
+ * @buff: The buffer address
+ * @len: The length of the data to read
+ *
+ * Issue an RXQ FIFO read command and read the @len ammount of data from
+ * the FIFO into the buffer specified by @buff.
+ */
+static void ks8851_rdfifo(struct ks8851_net *ks, u8 *buff, unsigned len)
+{
+	struct spi_transfer *xfer = ks->spi_xfer2;
+	struct spi_message *msg = &ks->spi_msg2;
+	u8 txb[1];
+	int ret;
+
+	if (netif_msg_rx_status(ks))
+		ks_dbg(ks, "%s: %d@%p\n", __func__, len, buff);
+
+	/* set the operation we're issuing */
+	txb[0] = KS_SPIOP_RXFIFO;
+
+	xfer->tx_buf = txb;
+	xfer->rx_buf = NULL;
+	xfer->len = 1;
+
+	xfer++;
+	xfer->rx_buf = buff;
+	xfer->tx_buf = NULL;
+	xfer->len = len;
+
+	ret = spi_sync(ks->spidev, msg);
+	if (ret < 0)
+		ks_err(ks, "%s: spi_sync() failed\n", __func__);
+}
+
+/**
+ * ks8851_dbg_dumpkkt - dump initial packet contents to debug
+ * @ks: The device state
+ * @rxpkt: The data for the received packet
+ *
+ * Dump the initial data from the packet to dev_dbg().
+*/
+static void ks8851_dbg_dumpkkt(struct ks8851_net *ks, u8 *rxpkt)
+{
+	ks_dbg(ks, "pkt %02x%02x%02x%02x %02x%02x%02x%02x %02x%02x%02x%02x\n",
+	       rxpkt[4], rxpkt[5], rxpkt[6], rxpkt[7],
+	       rxpkt[8], rxpkt[9], rxpkt[10], rxpkt[11],
+	       rxpkt[12], rxpkt[13], rxpkt[14], rxpkt[15]);
+}
+
+/**
+ * ks8851_rx_pkts - receive packets from the host
+ * @ks: The device information.
+ *
+ * This is called from the IRQ work queue when the system detects that there
+ * are packets in the receive queue. Find out how many packets there are and
+ * read them from the FIFO.
+ */
+static void ks8851_rx_pkts(struct ks8851_net *ks)
+{
+	struct sk_buff *skb;
+	unsigned rxfc;
+	unsigned rxlen;
+	unsigned rxstat;
+	u32 rxh;
+	u8 *rxpkt;
+
+	rxfc = ks8851_rdreg8(ks, KS_RXFC);
+
+	if (netif_msg_rx_status(ks))
+		ks_dbg(ks, "%s: %d packets\n", __func__, rxfc);
+
+	/* Currently we're issuing a read per packet, but we could possibly
+	 * improve the code by issuing a single read, getting the receive
+	 * header, allocating the packet and then reading the packet data
+	 * out in one go.
+	 *
+	 * This form of operation would require us to hold the SPI bus'
+	 * chipselect low during the entie transaction to avoid any
+	 * reset to the data stream comming from the chip.
+	 */
+
+	for (; rxfc != 0; rxfc--) {
+		rxh = ks8851_rdreg32(ks, KS_RXFHSR);
+		rxstat = rxh & 0xffff;
+		rxlen = rxh >> 16;
+
+		if (netif_msg_rx_status(ks))
+			ks_dbg(ks, "rx: stat 0x%04x, len 0x%04x\n",
+				rxstat, rxlen);
+
+		/* the length of the packet includes the 32bit CRC */
+
+		/* set dma read address */
+		ks8851_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI | 0x00);
+
+		/* start the packet dma process, and set auto-dequeue rx */
+		ks8851_wrreg16(ks, KS_RXQCR,
+			       ks->rc_rxqcr | RXQCR_SDA | RXQCR_ADRFE);
+
+		if (rxlen > 0) {
+			skb = netdev_alloc_skb(ks->netdev, rxlen + 2 + 8);
+			if (!skb) {
+				/* todo - dump frame and move on */
+			}
+
+			/* two bytes to ensure ip is aligned, and four bytes
+			 * for the status header and 4 bytes of garbage */
+			skb_reserve(skb, 2 + 4 + 4);
+
+			rxpkt = skb_put(skb, rxlen - 4) - 8;
+
+			/* align the packet length to 4 bytes, and add 4 bytes
+			 * as we're getting the rx status header as well */
+			ks8851_rdfifo(ks, rxpkt, ALIGN(rxlen, 4) + 8);
+
+			if (netif_msg_pktdata(ks))
+				ks8851_dbg_dumpkkt(ks, rxpkt);
+
+			skb->protocol = eth_type_trans(skb, ks->netdev);
+			netif_rx(skb);
+
+			ks->netdev->stats.rx_packets++;
+			ks->netdev->stats.rx_bytes += rxlen - 4;
+		}
+
+		ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
+	}
+}
+
+/**
+ * ks8851_irq_work - work queue handler for dealing with interrupt requests
+ * @work: The work structure that was scheduled by schedule_work()
+ *
+ * This is the handler invoked when the ks8851_irq() is called to find out
+ * what happened, as we cannot allow ourselves to sleep whilst waiting for
+ * anything other process has the chip's lock.
+ *
+ * Read the interrupt status, work out what needs to be done and then clear
+ * any of the interrupts that are not needed.
+ */
+static void ks8851_irq_work(struct work_struct *work)
+{
+	struct ks8851_net *ks = container_of(work, struct ks8851_net, irq_work);
+	unsigned status;
+	unsigned handled = 0;
+
+	mutex_lock(&ks->lock);
+
+	status = ks8851_rdreg16(ks, KS_ISR);
+
+	if (netif_msg_intr(ks))
+		dev_dbg(&ks->spidev->dev, "%s: status 0x%04x\n",
+			__func__, status);
+
+	if (status & IRQ_LCI) {
+		/* should do something about checking link status */
+		handled |= IRQ_LCI;
+	}
+
+	if (status & IRQ_LDI) {
+		u16 pmecr = ks8851_rdreg16(ks, KS_PMECR);
+		pmecr &= ~PMECR_WKEVT_MASK;
+		ks8851_wrreg16(ks, KS_PMECR, pmecr | PMECR_WKEVT_LINK);
+
+		handled |= IRQ_LDI;
+	}
+
+	if (status & IRQ_RXPSI)
+		handled |= IRQ_RXPSI;
+
+	if (status & IRQ_TXI) {
+		handled |= IRQ_TXI;
+
+		/* no lock here, tx queue should have been stopped */
+
+		/* update our idea of how much tx space is available to the
+		 * system */
+		ks->tx_space = ks8851_rdreg16(ks, KS_TXMIR);
+
+		if (netif_msg_intr(ks))
+			ks_dbg(ks, "%s: txspace %d\n", __func__, ks->tx_space);
+	}
+
+	if (status & IRQ_RXI)
+		handled |= IRQ_RXI;
+
+	if (status & IRQ_SPIBEI) {
+		dev_err(&ks->spidev->dev, "%s: spi bus error\n", __func__);
+		handled |= IRQ_SPIBEI;
+	}
+
+	ks8851_wrreg16(ks, KS_ISR, handled);
+
+	if (status & IRQ_RXI) {
+		/* the datasheet says to disable the rx interrupt during
+		 * packet read-out, however we're masking the interrupt
+		 * from the device so do not bother masking just the RX
+		 * from the device. */
+
+		ks8851_rx_pkts(ks);
+	}
+
+	/* if something stopped the rx process, probably due to wanting
+	 * to change the rx settings, then do something about restarting
+	 * it. */
+	if (status & IRQ_RXPSI) {
+		struct ks8851_rxctrl *rxc = &ks->rxctrl;
+
+		/* update the multicast hash table */
+		ks8851_wrreg16(ks, KS_MAHTR0, rxc->mchash[0]);
+		ks8851_wrreg16(ks, KS_MAHTR1, rxc->mchash[1]);
+		ks8851_wrreg16(ks, KS_MAHTR2, rxc->mchash[2]);
+		ks8851_wrreg16(ks, KS_MAHTR3, rxc->mchash[3]);
+
+		ks8851_wrreg16(ks, KS_RXCR2, rxc->rxcr2);
+		ks8851_wrreg16(ks, KS_RXCR1, rxc->rxcr1);
+	}
+
+	mutex_unlock(&ks->lock);
+
+	if (status & IRQ_TXI)
+		netif_wake_queue(ks->netdev);
+
+	enable_irq(ks->netdev->irq);
+}
+
+/**
+ * calc_txlen - calculate size of message to send packet
+ * @len: Lenght of data
+ *
+ * Returns the size of the TXFIFO message needed to send
+ * this packet.
+ */
+static inline unsigned calc_txlen(unsigned len)
+{
+	return ALIGN(len + 4, 4);
+}
+
+/**
+ * ks8851_wrpkt - write packet to TX FIFO
+ * @ks: The device state.
+ * @txp: The sk_buff to transmit.
+ * @irq: IRQ on completion of the packet.
+ *
+ * Send the @txp to the chip. This means creating the relevant packet header
+ * specifying the length of the packet and the other information the chip
+ * needs, such as IRQ on completion. Send the header and the packet data to
+ * the device.
+ */
+static void ks8851_wrpkt(struct ks8851_net *ks, struct sk_buff *txp, bool irq)
+{
+	struct spi_transfer *xfer = ks->spi_xfer2;
+	struct spi_message *msg = &ks->spi_msg2;
+	unsigned fid = 0;
+	int ret;
+
+	if (netif_msg_tx_queued(ks))
+		dev_dbg(&ks->spidev->dev, "%s: skb %p, %d@%p, irq %d\n",
+			__func__, txp, txp->len, txp->data, irq);
+
+	fid = ks->fid++;
+	fid &= TXFR_TXFID_MASK;
+
+	if (irq)
+		fid |= TXFR_TXIC;	/* irq on completion */
+
+	/* start header at txb[1] to align txw entries */
+	ks->txh.txb[1] = KS_SPIOP_TXFIFO;
+	ks->txh.txw[1] = cpu_to_le16(fid);
+	ks->txh.txw[2] = cpu_to_le16(txp->len);
+
+	xfer->tx_buf = &ks->txh.txb[1];
+	xfer->rx_buf = NULL;
+	xfer->len = 5;
+
+	xfer++;
+	xfer->tx_buf = txp->data;
+	xfer->rx_buf = NULL;
+	xfer->len = ALIGN(txp->len, 4);
+
+	ret = spi_sync(ks->spidev, msg);
+	if (ret < 0)
+		ks_err(ks, "%s: spi_sync() failed\n", __func__);
+}
+
+/**
+ * ks8851_done_tx - update and then free skbuff after transmitting
+ * @ks: The device state
+ * @txb: The buffer transmitted
+ */
+static void ks8851_done_tx(struct ks8851_net *ks, struct sk_buff *txb)
+{
+	struct net_device *dev = ks->netdev;
+
+	dev->stats.tx_bytes += txb->len;
+	dev->stats.tx_packets++;
+
+	dev_kfree_skb(txb);
+}
+
+/**
+ * ks8851_tx_work - process tx packet(s)
+ * @work: The work strucutre what was scheduled.
+ *
+ * This is called when a number of packets have been scheduled for
+ * transmission and need to be sent to the device.
+ */
+static void ks8851_tx_work(struct work_struct *work)
+{
+	struct ks8851_net *ks = container_of(work, struct ks8851_net, tx_work);
+	struct sk_buff *txb;
+	bool last = false;
+
+	mutex_lock(&ks->lock);
+
+	while (!last) {
+		txb = skb_dequeue(&ks->txq);
+		last = skb_queue_empty(&ks->txq);
+
+		ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr | RXQCR_SDA);
+		ks8851_wrpkt(ks, txb, last);
+		ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
+		ks8851_wrreg16(ks, KS_TXQCR, TXQCR_METFE);
+
+		ks8851_done_tx(ks, txb);
+	}
+
+	mutex_unlock(&ks->lock);
+}
+
+/**
+ * ks8851_set_powermode - set power mode of the device
+ * @ks: The device state
+ * @pwrmode: The power mode value to write to KS_PMECR.
+ *
+ * Change the power mode of the chip.
+ */
+static void ks8851_set_powermode(struct ks8851_net *ks, unsigned pwrmode)
+{
+	unsigned pmecr;
+
+	if (netif_msg_hw(ks))
+		ks_dbg(ks, "setting power mode %d\n", pwrmode);
+
+	pmecr = ks8851_rdreg16(ks, KS_PMECR);
+	pmecr &= ~PMECR_PM_MASK;
+	pmecr |= pwrmode;
+
+	ks8851_wrreg16(ks, KS_PMECR, pmecr);
+}
+
+/**
+ * ks8851_net_open - open network device
+ * @dev: The network device being opened.
+ *
+ * Called when the network device is marked active, such as a user executing
+ * 'ifconfig up' on the device.
+ */
+static int ks8851_net_open(struct net_device *dev)
+{
+	struct ks8851_net *ks = netdev_priv(dev);
+
+	/* lock the card, even if we may not actually be doing anything
+	 * else at the moment */
+	mutex_lock(&ks->lock);
+
+	if (netif_msg_ifup(ks))
+		ks_dbg(ks, "opening %s\n", dev->name);
+
+	/* bring chip out of any power saving mode it was in */
+	ks8851_set_powermode(ks, PMECR_PM_NORMAL);
+
+	/* issue a soft reset to the RX/TX QMU to put it into a known
+	 * state. */
+	ks8851_soft_reset(ks, GRR_QMU);
+
+	/* setup transmission parameters */
+
+	ks8851_wrreg16(ks, KS_TXCR, (TXCR_TXE | /* enable transmit process */
+				     TXCR_TXPE | /* pad to min length */
+				     TXCR_TXCRC | /* add CRC */
+				     TXCR_TXFCE)); /* enable flow control */
+
+	/* auto-increment tx data, reset tx pointer */
+	ks8851_wrreg16(ks, KS_TXFDPR, TXFDPR_TXFPAI);
+
+	/* setup receiver control */
+
+	ks8851_wrreg16(ks, KS_RXCR1, (RXCR1_RXPAFMA | /*  from mac filter */
+				      RXCR1_RXFCE | /* enable flow control */
+				      RXCR1_RXBE | /* broadcast enable */
+				      RXCR1_RXUE | /* unicast enable */
+				      RXCR1_RXE)); /* enable rx block */
+
+	/* transfer entire frames out in one go */
+	ks8851_wrreg16(ks, KS_RXCR2, RXCR2_SRDBL_FRAME);
+
+	/* set receive counter timeouts */
+	ks8851_wrreg16(ks, KS_RXDTTR, 1000); /* 1ms after first frame to IRQ */
+	ks8851_wrreg16(ks, KS_RXDBCTR, 4096); /* >4Kbytes in buffer to IRQ */
+	ks8851_wrreg16(ks, KS_RXFCTR, 10);  /* 10 frames to IRQ */
+
+	ks->rc_rxqcr = (RXQCR_RXFCTE |  /* IRQ on frame count exceeded */
+			RXQCR_RXDBCTE | /* IRQ on byte count exceeded */
+			RXQCR_RXDTTE);  /* IRQ on time exceeded */
+
+	ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
+
+	/* clear then enable interrupts */
+
+#define STD_IRQ (IRQ_LCI |	/* Link Change */	\
+		 IRQ_TXI |	/* TX done */		\
+		 IRQ_RXI |	/* RX done */		\
+		 IRQ_SPIBEI |	/* SPI bus error */	\
+		 IRQ_TXPSI |	/* TX process stop */	\
+		 IRQ_RXPSI)	/* RX process stop */
+
+	ks->rc_ier = STD_IRQ;
+	ks8851_wrreg16(ks, KS_ISR, STD_IRQ);
+	ks8851_wrreg16(ks, KS_IER, STD_IRQ);
+
+	netif_start_queue(ks->netdev);
+
+	if (netif_msg_ifup(ks))
+		ks_dbg(ks, "network device %s up\n", dev->name);
+
+	mutex_unlock(&ks->lock);
+	return 0;
+}
+
+/**
+ * ks8851_net_stop - close network device
+ * @dev: The device being closed.
+ *
+ * Called to close down a network device which has been active. Cancell any
+ * work, shutdown the RX and TX process and then place the chip into a low
+ * power state whilst it is not being used.
+ */
+static int ks8851_net_stop(struct net_device *dev)
+{
+	struct ks8851_net *ks = netdev_priv(dev);
+
+	if (netif_msg_ifdown(ks))
+		ks_info(ks, "%s: shutting down\n", dev->name);
+
+	netif_stop_queue(dev);
+
+	mutex_lock(&ks->lock);
+
+	/* stop any outstanding work */
+	flush_work(&ks->irq_work);
+	flush_work(&ks->tx_work);
+	flush_work(&ks->rxctrl_work);
+
+	/* turn off the IRQs and ack any outstanding */
+	ks8851_wrreg16(ks, KS_IER, 0x0000);
+	ks8851_wrreg16(ks, KS_ISR, 0xffff);
+
+	/* shutdown RX process */
+	ks8851_wrreg16(ks, KS_RXCR1, 0x0000);
+
+	/* shutdown TX process */
+	ks8851_wrreg16(ks, KS_TXCR, 0x0000);
+
+	/* set powermode to soft power down to save power */
+	ks8851_set_powermode(ks, PMECR_PM_SOFTDOWN);
+
+	/* ensure any queued tx buffers are dumped */
+	while (!skb_queue_empty(&ks->txq)) {
+		struct sk_buff *txb = skb_dequeue(&ks->txq);
+
+		if (netif_msg_ifdown(ks))
+			ks_dbg(ks, "%s: freeing txb %p\n", __func__, txb);
+
+		dev_kfree_skb(txb);
+	}
+
+	mutex_unlock(&ks->lock);
+	return 0;
+}
+
+/**
+ * ks8851_start_xmit - transmit packet
+ * @skb: The buffer to transmit
+ * @dev: The device used to transmit the packet.
+ *
+ * Called by the network layer to transmit the @skb. Queue the packet for
+ * the device and schedule the necessary work to transmit the packet when
+ * it is free.
+ *
+ * We do this to firstly avoid sleeping with the network device locked,
+ * and secondly so we can round up more than one packet to transmit which
+ * means we can try and avoid generating too many transmit done interrupts.
+ */
+static int ks8851_start_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+	struct ks8851_net *ks = netdev_priv(dev);
+	unsigned needed = calc_txlen(skb->len);
+	int ret = NETDEV_TX_OK;
+
+	if (netif_msg_tx_queued(ks))
+		ks_dbg(ks, "%s: skb %p, %d@%p\n", __func__,
+		       skb, skb->len, skb->data);
+
+	spin_lock(&ks->statelock);
+
+	if (needed > ks->tx_space) {
+		netif_stop_queue(dev);
+		ret = NETDEV_TX_BUSY;
+	} else {
+		ks->tx_space -= needed;
+		skb_queue_tail(&ks->txq, skb);
+	}
+
+	spin_unlock(&ks->statelock);
+	schedule_work(&ks->tx_work);
+
+	return ret;
+}
+
+/**
+ * ks8851_rxctrl_work - work handler to change rx mode
+ * @work: The work structure this belongs to.
+ *
+ * Lock the device and issue the necessary changes to the receive mode from
+ * the network device layer. This is done so that we can do this without
+ * having to sleep whilst holding the network device lock.
+ *
+ * Since the recommendation from Micrel is that the RXQ is shutdown whilst the
+ * receive parameters are programmed, we issue a write to disable the RXQ and
+ * then wait for the interrupt handler to be triggered once the RXQ shutdown is
+ * complete. The interrupt handler then writes the new values into the chip.
+ */
+static void ks8851_rxctrl_work(struct work_struct *work)
+{
+	struct ks8851_net *ks = container_of(work, struct ks8851_net, rxctrl_work);
+
+	mutex_lock(&ks->lock);
+
+	/* need to shutdown RXQ before modifying filter parameters */
+	ks8851_wrreg16(ks, KS_RXCR1, 0x00);
+
+	mutex_unlock(&ks->lock);
+}
+
+static void ks8851_set_rx_mode(struct net_device *dev)
+{
+	struct ks8851_net *ks = netdev_priv(dev);
+	struct ks8851_rxctrl rxctrl;
+
+	memset(&rxctrl, 0, sizeof(rxctrl));
+
+	if (dev->flags & IFF_PROMISC) {
+		/* interface to receive everything */
+
+		rxctrl.rxcr1 = RXCR1_RXAE | RXCR1_RXINVF;
+	} else if (dev->flags & IFF_ALLMULTI) {
+		/* accept all multicast packets */
+
+		rxctrl.rxcr1 = (RXCR1_RXME | RXCR1_RXAE |
+				RXCR1_RXPAFMA | RXCR1_RXMAFMA);
+	} else if (dev->flags & IFF_MULTICAST && dev->mc_count > 0) {
+		struct dev_mc_list *mcptr = dev->mc_list;
+		u32 crc;
+		int i;
+
+		/* accept some multicast */
+
+		for (i = dev->mc_count; i > 0; i--) {
+			crc = ether_crc(ETH_ALEN, mcptr->dmi_addr);
+			crc >>= (32 - 6);  /* get top six bits */
+
+			rxctrl.mchash[crc >> 4] |= (1 << (crc & 0xf));
+			mcptr = mcptr->next;
+		}
+
+		rxctrl.rxcr1 = RXCR1_RXME | RXCR1_RXAE | RXCR1_RXPAFMA;
+	} else {
+		/* just accept broadcast / unicast */
+		rxctrl.rxcr1 = RXCR1_RXPAFMA;
+	}
+
+	rxctrl.rxcr1 |= (RXCR1_RXUE | /* unicast enable */
+			 RXCR1_RXBE | /* broadcast enable */
+			 RXCR1_RXE | /* RX process enable */
+			 RXCR1_RXFCE); /* enable flow control */
+
+	rxctrl.rxcr2 |= RXCR2_SRDBL_FRAME;
+
+	/* schedule work to do the actual set of the data if needed */
+
+	spin_lock(&ks->statelock);
+
+	if (memcmp(&rxctrl, &ks->rxctrl, sizeof(rxctrl)) != 0) {
+		memcpy(&ks->rxctrl, &rxctrl, sizeof(ks->rxctrl));
+		schedule_work(&ks->rxctrl_work);
+	}
+
+	spin_unlock(&ks->statelock);
+}
+
+static int ks8851_set_mac_address(struct net_device *dev, void *addr)
+{
+	struct sockaddr *sa = addr;
+
+	if (netif_running(dev))
+		return -EBUSY;
+
+	if (!is_valid_ether_addr(sa->sa_data))
+		return -EADDRNOTAVAIL;
+
+	memcpy(dev->dev_addr, sa->sa_data, ETH_ALEN);
+	return ks8851_write_mac_addr(dev);
+}
+
+static int ks8851_net_ioctl(struct net_device *dev, struct ifreq *req, int cmd)
+{
+	struct ks8851_net *ks = netdev_priv(dev);
+
+	if (!netif_running(dev))
+		return -EINVAL;
+
+	return generic_mii_ioctl(&ks->mii, if_mii(req), cmd, NULL);
+}
+
+static const struct net_device_ops ks8851_netdev_ops = {
+	.ndo_open		= ks8851_net_open,
+	.ndo_stop		= ks8851_net_stop,
+	.ndo_do_ioctl		= ks8851_net_ioctl,
+	.ndo_start_xmit		= ks8851_start_xmit,
+	.ndo_set_mac_address	= ks8851_set_mac_address,
+	.ndo_set_rx_mode	= ks8851_set_rx_mode,
+	.ndo_change_mtu		= eth_change_mtu,
+	.ndo_validate_addr	= eth_validate_addr,
+};
+
+/* ethtool support */
+
+static void ks8851_get_drvinfo(struct net_device *dev,
+			       struct ethtool_drvinfo *di)
+{
+	strlcpy(di->driver, "KS8851", sizeof(di->driver));
+	strlcpy(di->version, "1.00", sizeof(di->version));
+	strlcpy(di->bus_info, dev_name(dev->dev.parent), sizeof(di->bus_info));
+}
+
+static u32 ks8851_get_msglevel(struct net_device *dev)
+{
+	struct ks8851_net *ks = netdev_priv(dev);
+	return ks->msg_enable;
+}
+
+static void ks8851_set_msglevel(struct net_device *dev, u32 to)
+{
+	struct ks8851_net *ks = netdev_priv(dev);
+	ks->msg_enable = to;
+}
+
+static int ks8851_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+{
+	struct ks8851_net *ks = netdev_priv(dev);
+	return mii_ethtool_gset(&ks->mii, cmd);
+}
+
+static int ks8851_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
+{
+	struct ks8851_net *ks = netdev_priv(dev);
+	return mii_ethtool_sset(&ks->mii, cmd);
+}
+
+static u32 ks8851_get_link(struct net_device *dev)
+{
+	struct ks8851_net *ks = netdev_priv(dev);
+	return mii_link_ok(&ks->mii);
+}
+
+static int ks8851_nway_reset(struct net_device *dev)
+{
+	struct ks8851_net *ks = netdev_priv(dev);
+	return mii_nway_restart(&ks->mii);
+}
+
+static const struct ethtool_ops ks8851_ethtool_ops = {
+	.get_drvinfo	= ks8851_get_drvinfo,
+	.get_msglevel	= ks8851_get_msglevel,
+	.set_msglevel	= ks8851_set_msglevel,
+	.get_settings	= ks8851_get_settings,
+	.set_settings	= ks8851_set_settings,
+	.get_link	= ks8851_get_link,
+	.nway_reset	= ks8851_nway_reset,
+};
+
+/* MII interface controls */
+
+/**
+ * ks8851_phy_reg - convert MII register into a KS8851 register
+ * @reg: MII register number.
+ *
+ * Return the KS8851 register number for the corresponding MII PHY register
+ * if possible. Return zero if the MII register has no direct mapping to the
+ * KS8851 register set.
+ */
+static int ks8851_phy_reg(int reg)
+{
+	switch (reg) {
+	case MII_BMCR:
+		return KS_P1MBCR;
+	case MII_BMSR:
+		return KS_P1MBSR;
+	case MII_PHYSID1:
+		return KS_PHY1ILR;
+	case MII_PHYSID2:
+		return KS_PHY1IHR;
+	case MII_ADVERTISE:
+		return KS_P1ANAR;
+	case MII_LPA:
+		return KS_P1ANLPR;
+	}
+
+	return 0x0;
+}
+
+/**
+ * ks8851_phy_read - MII interface PHY register read.
+ * @dev: The network device the PHY is on.
+ * @phy_addr: Address of PHY (ignored as we only have one)
+ * @reg: The register to read.
+ *
+ * This call reads data from the PHY register specified in @reg. Since the
+ * device does not support all the MII registers, the non-existant values
+ * are always returned as zero.
+ *
+ * We return zero for unsupported registers as the MII code does not check
+ * the value returned for any error status, and simply returns it to the
+ * caller. The mii-tool that the driver was tested with takes any -ve error
+ * as real PHY capabilities, thus displaying incorrect data to the user.
+ */
+static int ks8851_phy_read(struct net_device *dev, int phy_addr, int reg)
+{
+	struct ks8851_net *ks = netdev_priv(dev);
+	int ksreg;
+	int result;
+
+	ksreg = ks8851_phy_reg(reg);
+	if (!ksreg)
+		return 0x0;	/* no error return allowed, so use zero */
+
+	mutex_lock(&ks->lock);
+	result = ks8851_rdreg16(ks, ksreg);
+	mutex_unlock(&ks->lock);
+
+	return result;
+}
+
+static void ks8851_phy_write(struct net_device *dev,
+			     int phy, int reg, int value)
+{
+	struct ks8851_net *ks = netdev_priv(dev);
+	int ksreg;
+
+	ksreg = ks8851_phy_reg(reg);
+	if (ksreg) {
+		mutex_lock(&ks->lock);
+		ks8851_wrreg16(ks, ksreg, value);
+		mutex_unlock(&ks->lock);
+	}
+}
+
+/**
+ * ks8851_read_selftest - read the selftest memory info.
+ * @ks: The device state
+ *
+ * Read and check the TX/RX memory selftest information.
+ */
+static int ks8851_read_selftest(struct ks8851_net *ks)
+{
+	unsigned both_done = MBIR_TXMBF | MBIR_RXMBF;
+	int ret = 0;
+	unsigned rd;
+
+	rd = ks8851_rdreg16(ks, KS_MBIR);
+
+	if ((rd & both_done) != both_done) {
+		ks_warn(ks, "Memory selftest not finished\n");
+		return 0;
+	}
+
+	if (rd & MBIR_TXMBFA) {
+		ks_err(ks, "TX memory selftest fail\n");
+		ret |= 1;
+	}
+
+	if (rd & MBIR_RXMBFA) {
+		ks_err(ks, "RX memory selftest fail\n");
+		ret |= 2;
+	}
+
+	return 0;
+}
+
+/* driver bus management functions */
+
+static int __devinit ks8851_probe(struct spi_device *spi)
+{
+	struct net_device *ndev;
+	struct ks8851_net *ks;
+	int ret;
+
+	ndev = alloc_etherdev(sizeof(struct ks8851_net));
+	if (!ndev) {
+		dev_err(&spi->dev, "failed to alloc ethernet device\n");
+		return -ENOMEM;
+	}
+
+	spi->bits_per_word = 8;
+
+	ks = netdev_priv(ndev);
+
+	ks->netdev = ndev;
+	ks->spidev = spi;
+	ks->tx_space = 6144;
+
+	mutex_init(&ks->lock);
+	spin_lock_init(&ks->statelock);
+
+	INIT_WORK(&ks->tx_work, ks8851_tx_work);
+	INIT_WORK(&ks->irq_work, ks8851_irq_work);
+	INIT_WORK(&ks->rxctrl_work, ks8851_rxctrl_work);
+
+	/* initialise pre-made spi transfer messages */
+
+	spi_message_init(&ks->spi_msg1);
+	spi_message_add_tail(&ks->spi_xfer1, &ks->spi_msg1);
+
+	spi_message_init(&ks->spi_msg2);
+	spi_message_add_tail(&ks->spi_xfer2[0], &ks->spi_msg2);
+	spi_message_add_tail(&ks->spi_xfer2[1], &ks->spi_msg2);
+
+	/* setup mii state */
+	ks->mii.dev		= ndev;
+	ks->mii.phy_id		= 1,
+	ks->mii.phy_id_mask	= 1;
+	ks->mii.reg_num_mask	= 0xf;
+	ks->mii.mdio_read	= ks8851_phy_read;
+	ks->mii.mdio_write	= ks8851_phy_write;
+
+	dev_info(&spi->dev, "message enable is %d\n", msg_enable);
+
+	/* set the default message enable */
+	ks->msg_enable = netif_msg_init(msg_enable, (NETIF_MSG_DRV |
+						     NETIF_MSG_PROBE |
+						     NETIF_MSG_LINK));
+
+	skb_queue_head_init(&ks->txq);
+
+	SET_ETHTOOL_OPS(ndev, &ks8851_ethtool_ops);
+	SET_NETDEV_DEV(ndev, &spi->dev);
+
+	dev_set_drvdata(&spi->dev, ks);
+
+	ndev->if_port = IF_PORT_100BASET;
+	ndev->netdev_ops = &ks8851_netdev_ops;
+	ndev->irq = spi->irq;
+
+	/* simple check for a valid chip being connected to the bus */
+
+	if ((ks8851_rdreg16(ks, KS_CIDER) & ~CIDER_REV_MASK) != CIDER_ID) {
+		dev_err(&spi->dev, "failed to read device ID\n");
+		ret = -ENODEV;
+		goto err_id;
+	}
+
+	ks8851_read_selftest(ks);
+	ks8851_init_mac(ks);
+
+	ret = request_irq(spi->irq, ks8851_irq, IRQF_TRIGGER_LOW,
+			  ndev->name, ks);
+	if (ret < 0) {
+		dev_err(&spi->dev, "failed to get irq\n");
+		goto err_irq;
+	}
+
+	ret = register_netdev(ndev);
+	if (ret) {
+		dev_err(&spi->dev, "failed to register network device\n");
+		goto err_netdev;
+	}
+
+	dev_info(&spi->dev, "revision %d, MAC %pM, IRQ %d\n",
+		 CIDER_REV_GET(ks8851_rdreg16(ks, KS_CIDER)),
+		 ndev->dev_addr, ndev->irq);
+
+	return 0;
+
+
+err_netdev:
+	free_irq(ndev->irq, ndev);
+
+err_id:
+err_irq:
+	free_netdev(ndev);
+	return ret;
+}
+
+static int __devexit ks8851_remove(struct spi_device *spi)
+{
+	struct ks8851_net *priv = dev_get_drvdata(&spi->dev);
+
+	if (netif_msg_drv(priv))
+		dev_info(&spi->dev, "remove");
+
+	unregister_netdev(priv->netdev);
+	free_irq(spi->irq, priv);
+	free_netdev(priv->netdev);
+
+	return 0;
+}
+
+static struct spi_driver ks8851_driver = {
+	.driver = {
+		.name = "ks8851",
+		.owner = THIS_MODULE,
+	},
+	.probe = ks8851_probe,
+	.remove = __devexit_p(ks8851_remove),
+};
+
+static int __init ks8851_init(void)
+{
+	return spi_register_driver(&ks8851_driver);
+}
+
+static void __exit ks8851_exit(void)
+{
+	spi_unregister_driver(&ks8851_driver);
+}
+
+module_init(ks8851_init);
+module_exit(ks8851_exit);
+
+MODULE_DESCRIPTION("KS8851 Network driver");
+MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
+MODULE_LICENSE("GPL");
+
+module_param_named(message, msg_enable, int, 0);
+MODULE_PARM_DESC(message, "Message verbosity level (0=none, 31=all)");

drivers/net/ks8851.h

+/* drivers/net/ks8851.h
+ *
+ * Copyright 2009 Simtec Electronics
+ *      Ben Dooks <ben@simtec.co.uk>
+ *
+ * KS8851 register definitions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#define KS_CCR					0x08
+#define CCR_EEPROM				(1 << 9)
+#define CCR_SPI					(1 << 8)
+#define CCR_32PIN				(1 << 0)
+
+/* MAC address registers */
+#define KS_MARL					0x10
+#define KS_MARM					0x12
+#define KS_MARH					0x14
+
+#define KS_OBCR					0x20
+#define OBCR_ODS_16mA				(1 << 6)
+
+#define KS_EEPCR				0x22
+#define EEPCR_EESA				(1 << 4)
+#define EEPCR_EESB				(1 << 3)
+#define EEPCR_EEDO				(1 << 2)
+#define EEPCR_EESCK				(1 << 1)
+#define EEPCR_EECS				(1 << 0)
+
+#define KS_MBIR					0x24
+#define MBIR_TXMBF				(1 << 12)
+#define MBIR_TXMBFA				(1 << 11)
+#define MBIR_RXMBF				(1 << 4)
+#define MBIR_RXMBFA				(1 << 3)
+
+#define KS_GRR					0x26
+#define GRR_QMU					(1 << 1)
+#define GRR_GSR					(1 << 0)
+
+#define KS_WFCR					0x2A
+#define WFCR_MPRXE				(1 << 7)
+#define WFCR_WF3E				(1 << 3)
+#define WFCR_WF2E				(1 << 2)
+#define WFCR_WF1E				(1 << 1)
+#define WFCR_WF0E				(1 << 0)
+
+#define KS_WF0CRC0				0x30
+#define KS_WF0CRC1				0x32
+#define KS_WF0BM0				0x34
+#define KS_WF0BM1				0x36
+#define KS_WF0BM2				0x38
+#define KS_WF0BM3				0x3A
+
+#define KS_WF1CRC0				0x40
+#define KS_WF1CRC1				0x42
+#define KS_WF1BM0				0x44
+#define KS_WF1BM1				0x46
+#define KS_WF1BM2				0x48
+#define KS_WF1BM3				0x4A
+
+#define KS_WF2CRC0				0x50
+#define KS_WF2CRC1				0x52
+#define KS_WF2BM0				0x54
+#define KS_WF2BM1				0x56
+#define KS_WF2BM2				0x58
+#define KS_WF2BM3				0x5A
+
+#define KS_WF3CRC0				0x60
+#define KS_WF3CRC1				0x62
+#define KS_WF3BM0				0x64
+#define KS_WF3BM1				0x66
+#define KS_WF3BM2				0x68
+#define KS_WF3BM3				0x6A
+
+#define KS_TXCR					0x70
+#define TXCR_TCGICMP				(1 << 8)
+#define TXCR_TCGUDP				(1 << 7)
+#define TXCR_TCGTCP				(1 << 6)
+#define TXCR_TCGIP				(1 << 5)
+#define TXCR_FTXQ				(1 << 4)
+#define TXCR_TXFCE				(1 << 3)
+#define TXCR_TXPE				(1 << 2)
+#define TXCR_TXCRC				(1 << 1)
+#define TXCR_TXE				(1 << 0)
+
+#define KS_TXSR					0x72
+#define TXSR_TXLC				(1 << 13)
+#define TXSR_TXMC				(1 << 12)
+#define TXSR_TXFID_MASK				(0x3f << 0)
+#define TXSR_TXFID_SHIFT			(0)
+#define TXSR_TXFID_GET(_v)			(((_v) >> 0) & 0x3f)
+
+#define KS_RXCR1				0x74
+#define RXCR1_FRXQ				(1 << 15)
+#define RXCR1_RXUDPFCC				(1 << 14)
+#define RXCR1_RXTCPFCC				(1 << 13)
+#define RXCR1_RXIPFCC				(1 << 12)
+#define RXCR1_RXPAFMA				(1 << 11)
+#define RXCR1_RXFCE				(1 << 10)
+#define RXCR1_RXEFE				(1 << 9)
+#define RXCR1_RXMAFMA				(1 << 8)
+#define RXCR1_RXBE				(1 << 7)
+#define RXCR1_RXME				(1 << 6)
+#define RXCR1_RXUE				(1 << 5)
+#define RXCR1_RXAE				(1 << 4)
+#define RXCR1_RXINVF				(1 << 1)
+#define RXCR1_RXE				(1 << 0)
+
+#define KS_RXCR2				0x76
+#define RXCR2_SRDBL_MASK			(0x7 << 5)
+#define RXCR2_SRDBL_SHIFT			(5)
+#define RXCR2_SRDBL_4B				(0x0 << 5)
+#define RXCR2_SRDBL_8B				(0x1 << 5)
+#define RXCR2_SRDBL_16B				(0x2 << 5)
+#define RXCR2_SRDBL_32B				(0x3 << 5)
+#define RXCR2_SRDBL_FRAME			(0x4 << 5)
+#define RXCR2_IUFFP				(1 << 4)
+#define RXCR2_RXIUFCEZ				(1 << 3)
+#define RXCR2_UDPLFE				(1 << 2)
+#define RXCR2_RXICMPFCC				(1 << 1)
+#define RXCR2_RXSAF				(1 << 0)
+
+#define KS_TXMIR				0x78
+
+#define KS_RXFHSR				0x7C
+#define RXFSHR_RXFV				(1 << 15)
+#define RXFSHR_RXICMPFCS			(1 << 13)
+#define RXFSHR_RXIPFCS				(1 << 12)
+#define RXFSHR_RXTCPFCS				(1 << 11)
+#define RXFSHR_RXUDPFCS				(1 << 10)
+#define RXFSHR_RXBF				(1 << 7)
+#define RXFSHR_RXMF				(1 << 6)
+#define RXFSHR_RXUF				(1 << 5)
+#define RXFSHR_RXMR				(1 << 4)
+#define RXFSHR_RXFT				(1 << 3)
+#define RXFSHR_RXFTL				(1 << 2)
+#define RXFSHR_RXRF				(1 << 1)
+#define RXFSHR_RXCE				(1 << 0)
+
+#define KS_RXFHBCR				0x7E
+#define KS_TXQCR				0x80
+#define TXQCR_AETFE				(1 << 2)
+#define TXQCR_TXQMAM				(1 << 1)
+#define TXQCR_METFE				(1 << 0)
+
+#define KS_RXQCR				0x82
+#define RXQCR_RXDTTS				(1 << 12)
+#define RXQCR_RXDBCTS				(1 << 11)
+#define RXQCR_RXFCTS				(1 << 10)
+#define RXQCR_RXIPHTOE				(1 << 9)
+#define RXQCR_RXDTTE				(1 << 7)
+#define RXQCR_RXDBCTE				(1 << 6)
+#define RXQCR_RXFCTE				(1 << 5)
+#define RXQCR_ADRFE				(1 << 4)
+#define RXQCR_SDA				(1 << 3)
+#define RXQCR_RRXEF				(1 << 0)
+
+#define KS_TXFDPR				0x84
+#define TXFDPR_TXFPAI				(1 << 14)
+#define TXFDPR_TXFP_MASK			(0x7ff << 0)
+#define TXFDPR_TXFP_SHIFT			(0)
+
+#define KS_RXFDPR				0x86
+#define RXFDPR_RXFPAI				(1 << 14)
+
+#define KS_RXDTTR				0x8C
+#define KS_RXDBCTR				0x8E
+
+#define KS_IER					0x90
+#define KS_ISR					0x92
+#define IRQ_LCI					(1 << 15)
+#define IRQ_TXI					(1 << 14)
+#define IRQ_RXI					(1 << 13)
+#define IRQ_RXOI				(1 << 11)
+#define IRQ_TXPSI				(1 << 9)
+#define IRQ_RXPSI				(1 << 8)
+#define IRQ_TXSAI				(1 << 6)
+#define IRQ_RXWFDI				(1 << 5)
+#define IRQ_RXMPDI				(1 << 4)
+#define IRQ_LDI					(1 << 3)
+#define IRQ_EDI					(1 << 2)
+#define IRQ_SPIBEI				(1 << 1)
+#define IRQ_DEDI				(1 << 0)
+
+#define KS_RXFCTR				0x9C
+#define KS_RXFC					0x9D
+#define RXFCTR_RXFC_MASK			(0xff << 8)
+#define RXFCTR_RXFC_SHIFT			(8)
+#define RXFCTR_RXFC_GET(_v)			(((_v) >> 8) & 0xff)
+#define RXFCTR_RXFCT_MASK			(0xff << 0)
+#define RXFCTR_RXFCT_SHIFT			(0)
+
+#define KS_TXNTFSR				0x9E
+
+#define KS_MAHTR0				0xA0
+#define KS_MAHTR1				0xA2
+#define KS_MAHTR2				0xA4
+#define KS_MAHTR3				0xA6
+
+#define KS_FCLWR				0xB0
+#define KS_FCHWR				0xB2
+#define KS_FCOWR				0xB4
+
+#define KS_CIDER				0xC0
+#define CIDER_ID				0x8870
+#define CIDER_REV_MASK				(0x7 << 1)
+#define CIDER_REV_SHIFT				(1)
+#define CIDER_REV_GET(_v)			(((_v) >> 1) & 0x7)
+
+#define KS_CGCR					0xC6
+
+#define KS_IACR					0xC8
+#define IACR_RDEN				(1 << 12)
+#define IACR_TSEL_MASK				(0x3 << 10)
+#define IACR_TSEL_SHIFT				(10)
+#define IACR_TSEL_MIB				(0x3 << 10)
+#define IACR_ADDR_MASK				(0x1f << 0)
+#define IACR_ADDR_SHIFT				(0)
+
+#define KS_IADLR				0xD0
+#define KS_IAHDR				0xD2
+
+#define KS_PMECR				0xD4
+#define PMECR_PME_DELAY				(1 << 14)
+#define PMECR_PME_POL				(1 << 12)
+#define PMECR_WOL_WAKEUP			(1 << 11)
+#define PMECR_WOL_MAGICPKT			(1 << 10)
+#define PMECR_WOL_LINKUP			(1 << 9)
+#define PMECR_WOL_ENERGY			(1 << 8)
+#define PMECR_AUTO_WAKE_EN			(1 << 7)
+#define PMECR_WAKEUP_NORMAL			(1 << 6)
+#define PMECR_WKEVT_MASK			(0xf << 2)
+#define PMECR_WKEVT_SHIFT			(2)
+#define PMECR_WKEVT_GET(_v)			(((_v) >> 2) & 0xf)
+#define PMECR_WKEVT_ENERGY			(0x1 << 2)
+#define PMECR_WKEVT_LINK			(0x2 << 2)
+#define PMECR_WKEVT_MAGICPKT			(0x4 << 2)
+#define PMECR_WKEVT_FRAME			(0x8 << 2)
+#define PMECR_PM_MASK				(0x3 << 0)
+#define PMECR_PM_SHIFT				(0)
+#define PMECR_PM_NORMAL				(0x0 << 0)
+#define PMECR_PM_ENERGY				(0x1 << 0)
+#define PMECR_PM_SOFTDOWN			(0x2 << 0)
+#define PMECR_PM_POWERSAVE			(0x3 << 0)
+
+/* Standard MII PHY data */
+#define KS_P1MBCR				0xE4
+#define KS_P1MBSR				0xE6
+#define KS_PHY1ILR				0xE8
+#define KS_PHY1IHR				0xEA
+#define KS_P1ANAR				0xEC
+#define KS_P1ANLPR				0xEE
+
+#define KS_P1SCLMD				0xF4
+#define P1SCLMD_LEDOFF				(1 << 15)
+#define P1SCLMD_TXIDS				(1 << 14)
+#define P1SCLMD_RESTARTAN			(1 << 13)
+#define P1SCLMD_DISAUTOMDIX			(1 << 10)
+#define P1SCLMD_FORCEMDIX			(1 << 9)
+#define P1SCLMD_AUTONEGEN			(1 << 7)
+#define P1SCLMD_FORCE100			(1 << 6)
+#define P1SCLMD_FORCEFDX			(1 << 5)
+#define P1SCLMD_ADV_FLOW			(1 << 4)
+#define P1SCLMD_ADV_100BT_FDX			(1 << 3)
+#define P1SCLMD_ADV_100BT_HDX			(1 << 2)
+#define P1SCLMD_ADV_10BT_FDX			(1 << 1)
+#define P1SCLMD_ADV_10BT_HDX			(1 << 0)
+
+#define KS_P1CR					0xF6
+#define P1CR_HP_MDIX				(1 << 15)
+#define P1CR_REV_POL				(1 << 13)
+#define P1CR_OP_100M				(1 << 10)
+#define P1CR_OP_FDX				(1 << 9)
+#define P1CR_OP_MDI				(1 << 7)
+#define P1CR_AN_DONE				(1 << 6)
+#define P1CR_LINK_GOOD				(1 << 5)
+#define P1CR_PNTR_FLOW				(1 << 4)
+#define P1CR_PNTR_100BT_FDX			(1 << 3)
+#define P1CR_PNTR_100BT_HDX			(1 << 2)
+#define P1CR_PNTR_10BT_FDX			(1 << 1)
+#define P1CR_PNTR_10BT_HDX			(1 << 0)
+
+/* TX Frame control */
+
+#define TXFR_TXIC				(1 << 15)
+#define TXFR_TXFID_MASK				(0x3f << 0)
+#define TXFR_TXFID_SHIFT			(0)
+
+/* SPI frame opcodes */
+#define KS_SPIOP_RD				(0x00)
+#define KS_SPIOP_WR				(0x40)
+#define KS_SPIOP_RXFIFO				(0x80)
+#define KS_SPIOP_TXFIFO				(0xC0)