diff --git a/drivers/staging/lirc/lirc_serial.c b/drivers/staging/lirc/lirc_serial.c new file mode 100644 index 0000000000000000000000000000000000000000..d2ea3f0bd71d0eff58c8dfd480046eaf6cb6cd00 --- /dev/null +++ b/drivers/staging/lirc/lirc_serial.c @@ -0,0 +1,1313 @@ +/* + * lirc_serial.c + * + * lirc_serial - Device driver that records pulse- and pause-lengths + * (space-lengths) between DDCD event on a serial port. + * + * Copyright (C) 1996,97 Ralph Metzler + * Copyright (C) 1998 Trent Piepho + * Copyright (C) 1998 Ben Pfaff + * Copyright (C) 1999 Christoph Bartelmus + * Copyright (C) 2007 Andrei Tanas (suspend/resume support) + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +/* + * Steve's changes to improve transmission fidelity: + * - for systems with the rdtsc instruction and the clock counter, a + * send_pule that times the pulses directly using the counter. + * This means that the LIRC_SERIAL_TRANSMITTER_LATENCY fudge is + * not needed. Measurement shows very stable waveform, even where + * PCI activity slows the access to the UART, which trips up other + * versions. + * - For other system, non-integer-microsecond pulse/space lengths, + * done using fixed point binary. So, much more accurate carrier + * frequency. + * - fine tuned transmitter latency, taking advantage of fractional + * microseconds in previous change + * - Fixed bug in the way transmitter latency was accounted for by + * tuning the pulse lengths down - the send_pulse routine ignored + * this overhead as it timed the overall pulse length - so the + * pulse frequency was right but overall pulse length was too + * long. Fixed by accounting for latency on each pulse/space + * iteration. + * + * Steve Davies July 2001 + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include + +#ifdef CONFIG_LIRC_SERIAL_NSLU2 +#include +#endif +/* From Intel IXP42X Developer's Manual (#252480-005): */ +/* ftp://download.intel.com/design/network/manuals/25248005.pdf */ +#define UART_IE_IXP42X_UUE 0x40 /* IXP42X UART Unit enable */ +#define UART_IE_IXP42X_RTOIE 0x10 /* IXP42X Receiver Data Timeout int.enable */ + +#include +#include + +#define LIRC_DRIVER_NAME "lirc_serial" + +struct lirc_serial { + int signal_pin; + int signal_pin_change; + u8 on; + u8 off; + long (*send_pulse)(unsigned long length); + void (*send_space)(long length); + int features; + spinlock_t lock; +}; + +#define LIRC_HOMEBREW 0 +#define LIRC_IRDEO 1 +#define LIRC_IRDEO_REMOTE 2 +#define LIRC_ANIMAX 3 +#define LIRC_IGOR 4 +#define LIRC_NSLU2 5 + +/*** module parameters ***/ +static int type; +static int io; +static int irq; +static int iommap; +static int ioshift; +static int softcarrier = 1; +static int share_irq; +static int debug; +static int sense = -1; /* -1 = auto, 0 = active high, 1 = active low */ +static int txsense; /* 0 = active high, 1 = active low */ + +#define dprintk(fmt, args...) \ + do { \ + if (debug) \ + printk(KERN_DEBUG LIRC_DRIVER_NAME ": " \ + fmt, ## args); \ + } while (0) + +/* forward declarations */ +static long send_pulse_irdeo(unsigned long length); +static long send_pulse_homebrew(unsigned long length); +static void send_space_irdeo(long length); +static void send_space_homebrew(long length); + +static struct lirc_serial hardware[] = { + [LIRC_HOMEBREW] = { + .signal_pin = UART_MSR_DCD, + .signal_pin_change = UART_MSR_DDCD, + .on = (UART_MCR_RTS | UART_MCR_OUT2 | UART_MCR_DTR), + .off = (UART_MCR_RTS | UART_MCR_OUT2), + .send_pulse = send_pulse_homebrew, + .send_space = send_space_homebrew, +#ifdef CONFIG_LIRC_SERIAL_TRANSMITTER + .features = (LIRC_CAN_SET_SEND_DUTY_CYCLE | + LIRC_CAN_SET_SEND_CARRIER | + LIRC_CAN_SEND_PULSE | LIRC_CAN_REC_MODE2) +#else + .features = LIRC_CAN_REC_MODE2 +#endif + }, + + [LIRC_IRDEO] = { + .signal_pin = UART_MSR_DSR, + .signal_pin_change = UART_MSR_DDSR, + .on = UART_MCR_OUT2, + .off = (UART_MCR_RTS | UART_MCR_DTR | UART_MCR_OUT2), + .send_pulse = send_pulse_irdeo, + .send_space = send_space_irdeo, + .features = (LIRC_CAN_SET_SEND_DUTY_CYCLE | + LIRC_CAN_SEND_PULSE | LIRC_CAN_REC_MODE2) + }, + + [LIRC_IRDEO_REMOTE] = { + .signal_pin = UART_MSR_DSR, + .signal_pin_change = UART_MSR_DDSR, + .on = (UART_MCR_RTS | UART_MCR_DTR | UART_MCR_OUT2), + .off = (UART_MCR_RTS | UART_MCR_DTR | UART_MCR_OUT2), + .send_pulse = send_pulse_irdeo, + .send_space = send_space_irdeo, + .features = (LIRC_CAN_SET_SEND_DUTY_CYCLE | + LIRC_CAN_SEND_PULSE | LIRC_CAN_REC_MODE2) + }, + + [LIRC_ANIMAX] = { + .signal_pin = UART_MSR_DCD, + .signal_pin_change = UART_MSR_DDCD, + .on = 0, + .off = (UART_MCR_RTS | UART_MCR_DTR | UART_MCR_OUT2), + .send_pulse = NULL, + .send_space = NULL, + .features = LIRC_CAN_REC_MODE2 + }, + + [LIRC_IGOR] = { + .signal_pin = UART_MSR_DSR, + .signal_pin_change = UART_MSR_DDSR, + .on = (UART_MCR_RTS | UART_MCR_OUT2 | UART_MCR_DTR), + .off = (UART_MCR_RTS | UART_MCR_OUT2), + .send_pulse = send_pulse_homebrew, + .send_space = send_space_homebrew, +#ifdef CONFIG_LIRC_SERIAL_TRANSMITTER + .features = (LIRC_CAN_SET_SEND_DUTY_CYCLE | + LIRC_CAN_SET_SEND_CARRIER | + LIRC_CAN_SEND_PULSE | LIRC_CAN_REC_MODE2) +#else + .features = LIRC_CAN_REC_MODE2 +#endif + }, + +#ifdef CONFIG_LIRC_SERIAL_NSLU2 + /* + * Modified Linksys Network Storage Link USB 2.0 (NSLU2): + * We receive on CTS of the 2nd serial port (R142,LHS), we + * transmit with a IR diode between GPIO[1] (green status LED), + * and ground (Matthias Goebl ). + * See also http://www.nslu2-linux.org for this device + */ + [LIRC_NSLU2] = { + .signal_pin = UART_MSR_CTS, + .signal_pin_change = UART_MSR_DCTS, + .on = (UART_MCR_RTS | UART_MCR_OUT2 | UART_MCR_DTR), + .off = (UART_MCR_RTS | UART_MCR_OUT2), + .send_pulse = send_pulse_homebrew, + .send_space = send_space_homebrew, +#ifdef CONFIG_LIRC_SERIAL_TRANSMITTER + .features = (LIRC_CAN_SET_SEND_DUTY_CYCLE | + LIRC_CAN_SET_SEND_CARRIER | + LIRC_CAN_SEND_PULSE | LIRC_CAN_REC_MODE2) +#else + .features = LIRC_CAN_REC_MODE2 +#endif + }, +#endif + +}; + +#define RS_ISR_PASS_LIMIT 256 + +/* + * A long pulse code from a remote might take up to 300 bytes. The + * daemon should read the bytes as soon as they are generated, so take + * the number of keys you think you can push before the daemon runs + * and multiply by 300. The driver will warn you if you overrun this + * buffer. If you have a slow computer or non-busmastering IDE disks, + * maybe you will need to increase this. + */ + +/* This MUST be a power of two! It has to be larger than 1 as well. */ + +#define RBUF_LEN 256 + +static struct timeval lasttv = {0, 0}; + +static struct lirc_buffer rbuf; + +static unsigned int freq = 38000; +static unsigned int duty_cycle = 50; + +/* Initialized in init_timing_params() */ +static unsigned long period; +static unsigned long pulse_width; +static unsigned long space_width; + +#if defined(__i386__) +/* + * From: + * Linux I/O port programming mini-HOWTO + * Author: Riku Saikkonen + * v, 28 December 1997 + * + * [...] + * Actually, a port I/O instruction on most ports in the 0-0x3ff range + * takes almost exactly 1 microsecond, so if you're, for example, using + * the parallel port directly, just do additional inb()s from that port + * to delay. + * [...] + */ +/* transmitter latency 1.5625us 0x1.90 - this figure arrived at from + * comment above plus trimming to match actual measured frequency. + * This will be sensitive to cpu speed, though hopefully most of the 1.5us + * is spent in the uart access. Still - for reference test machine was a + * 1.13GHz Athlon system - Steve + */ + +/* + * changed from 400 to 450 as this works better on slower machines; + * faster machines will use the rdtsc code anyway + */ +#define LIRC_SERIAL_TRANSMITTER_LATENCY 450 + +#else + +/* does anybody have information on other platforms ? */ +/* 256 = 1<<8 */ +#define LIRC_SERIAL_TRANSMITTER_LATENCY 256 + +#endif /* __i386__ */ +/* + * FIXME: should we be using hrtimers instead of this + * LIRC_SERIAL_TRANSMITTER_LATENCY nonsense? + */ + +/* fetch serial input packet (1 byte) from register offset */ +static u8 sinp(int offset) +{ + if (iommap != 0) + /* the register is memory-mapped */ + offset <<= ioshift; + + return inb(io + offset); +} + +/* write serial output packet (1 byte) of value to register offset */ +static void soutp(int offset, u8 value) +{ + if (iommap != 0) + /* the register is memory-mapped */ + offset <<= ioshift; + + outb(value, io + offset); +} + +static void on(void) +{ +#ifdef CONFIG_LIRC_SERIAL_NSLU2 + /* + * On NSLU2, we put the transmit diode between the output of the green + * status LED and ground + */ + if (type == LIRC_NSLU2) { + gpio_line_set(NSLU2_LED_GRN, IXP4XX_GPIO_LOW); + return; + } +#endif + if (txsense) + soutp(UART_MCR, hardware[type].off); + else + soutp(UART_MCR, hardware[type].on); +} + +static void off(void) +{ +#ifdef CONFIG_LIRC_SERIAL_NSLU2 + if (type == LIRC_NSLU2) { + gpio_line_set(NSLU2_LED_GRN, IXP4XX_GPIO_HIGH); + return; + } +#endif + if (txsense) + soutp(UART_MCR, hardware[type].on); + else + soutp(UART_MCR, hardware[type].off); +} + +#ifndef MAX_UDELAY_MS +#define MAX_UDELAY_US 5000 +#else +#define MAX_UDELAY_US (MAX_UDELAY_MS*1000) +#endif + +static void safe_udelay(unsigned long usecs) +{ + while (usecs > MAX_UDELAY_US) { + udelay(MAX_UDELAY_US); + usecs -= MAX_UDELAY_US; + } + udelay(usecs); +} + +#ifdef USE_RDTSC +/* + * This is an overflow/precision juggle, complicated in that we can't + * do long long divide in the kernel + */ + +/* + * When we use the rdtsc instruction to measure clocks, we keep the + * pulse and space widths as clock cycles. As this is CPU speed + * dependent, the widths must be calculated in init_port and ioctl + * time + */ + +/* So send_pulse can quickly convert microseconds to clocks */ +static unsigned long conv_us_to_clocks; + +static int init_timing_params(unsigned int new_duty_cycle, + unsigned int new_freq) +{ + unsigned long long loops_per_sec, work; + + duty_cycle = new_duty_cycle; + freq = new_freq; + + loops_per_sec = current_cpu_data.loops_per_jiffy; + loops_per_sec *= HZ; + + /* How many clocks in a microsecond?, avoiding long long divide */ + work = loops_per_sec; + work *= 4295; /* 4295 = 2^32 / 1e6 */ + conv_us_to_clocks = (work >> 32); + + /* + * Carrier period in clocks, approach good up to 32GHz clock, + * gets carrier frequency within 8Hz + */ + period = loops_per_sec >> 3; + period /= (freq >> 3); + + /* Derive pulse and space from the period */ + pulse_width = period * duty_cycle / 100; + space_width = period - pulse_width; + dprintk("in init_timing_params, freq=%d, duty_cycle=%d, " + "clk/jiffy=%ld, pulse=%ld, space=%ld, " + "conv_us_to_clocks=%ld\n", + freq, duty_cycle, current_cpu_data.loops_per_jiffy, + pulse_width, space_width, conv_us_to_clocks); + return 0; +} +#else /* ! USE_RDTSC */ +static int init_timing_params(unsigned int new_duty_cycle, + unsigned int new_freq) +{ +/* + * period, pulse/space width are kept with 8 binary places - + * IE multiplied by 256. + */ + if (256 * 1000000L / new_freq * new_duty_cycle / 100 <= + LIRC_SERIAL_TRANSMITTER_LATENCY) + return -EINVAL; + if (256 * 1000000L / new_freq * (100 - new_duty_cycle) / 100 <= + LIRC_SERIAL_TRANSMITTER_LATENCY) + return -EINVAL; + duty_cycle = new_duty_cycle; + freq = new_freq; + period = 256 * 1000000L / freq; + pulse_width = period * duty_cycle / 100; + space_width = period - pulse_width; + dprintk("in init_timing_params, freq=%d pulse=%ld, " + "space=%ld\n", freq, pulse_width, space_width); + return 0; +} +#endif /* USE_RDTSC */ + + +/* return value: space length delta */ + +static long send_pulse_irdeo(unsigned long length) +{ + long rawbits, ret; + int i; + unsigned char output; + unsigned char chunk, shifted; + + /* how many bits have to be sent ? */ + rawbits = length * 1152 / 10000; + if (duty_cycle > 50) + chunk = 3; + else + chunk = 1; + for (i = 0, output = 0x7f; rawbits > 0; rawbits -= 3) { + shifted = chunk << (i * 3); + shifted >>= 1; + output &= (~shifted); + i++; + if (i == 3) { + soutp(UART_TX, output); + while (!(sinp(UART_LSR) & UART_LSR_THRE)) + ; + output = 0x7f; + i = 0; + } + } + if (i != 0) { + soutp(UART_TX, output); + while (!(sinp(UART_LSR) & UART_LSR_TEMT)) + ; + } + + if (i == 0) + ret = (-rawbits) * 10000 / 1152; + else + ret = (3 - i) * 3 * 10000 / 1152 + (-rawbits) * 10000 / 1152; + + return ret; +} + +#ifdef USE_RDTSC +/* Version that uses Pentium rdtsc instruction to measure clocks */ + +/* + * This version does sub-microsecond timing using rdtsc instruction, + * and does away with the fudged LIRC_SERIAL_TRANSMITTER_LATENCY + * Implicitly i586 architecture... - Steve + */ + +static long send_pulse_homebrew_softcarrier(unsigned long length) +{ + int flag; + unsigned long target, start, now; + + /* Get going quick as we can */ + rdtscl(start); + on(); + /* Convert length from microseconds to clocks */ + length *= conv_us_to_clocks; + /* And loop till time is up - flipping at right intervals */ + now = start; + target = pulse_width; + flag = 1; + /* + * FIXME: This looks like a hard busy wait, without even an occasional, + * polite, cpu_relax() call. There's got to be a better way? + * + * The i2c code has the result of a lot of bit-banging work, I wonder if + * there's something there which could be helpful here. + */ + while ((now - start) < length) { + /* Delay till flip time */ + do { + rdtscl(now); + } while ((now - start) < target); + + /* flip */ + if (flag) { + rdtscl(now); + off(); + target += space_width; + } else { + rdtscl(now); on(); + target += pulse_width; + } + flag = !flag; + } + rdtscl(now); + return ((now - start) - length) / conv_us_to_clocks; +} +#else /* ! USE_RDTSC */ +/* Version using udelay() */ + +/* + * here we use fixed point arithmetic, with 8 + * fractional bits. that gets us within 0.1% or so of the right average + * frequency, albeit with some jitter in pulse length - Steve + */ + +/* To match 8 fractional bits used for pulse/space length */ + +static long send_pulse_homebrew_softcarrier(unsigned long length) +{ + int flag; + unsigned long actual, target, d; + length <<= 8; + + actual = 0; target = 0; flag = 0; + while (actual < length) { + if (flag) { + off(); + target += space_width; + } else { + on(); + target += pulse_width; + } + d = (target - actual - + LIRC_SERIAL_TRANSMITTER_LATENCY + 128) >> 8; + /* + * Note - we've checked in ioctl that the pulse/space + * widths are big enough so that d is > 0 + */ + udelay(d); + actual += (d << 8) + LIRC_SERIAL_TRANSMITTER_LATENCY; + flag = !flag; + } + return (actual-length) >> 8; +} +#endif /* USE_RDTSC */ + +static long send_pulse_homebrew(unsigned long length) +{ + if (length <= 0) + return 0; + + if (softcarrier) + return send_pulse_homebrew_softcarrier(length); + else { + on(); + safe_udelay(length); + return 0; + } +} + +static void send_space_irdeo(long length) +{ + if (length <= 0) + return; + + safe_udelay(length); +} + +static void send_space_homebrew(long length) +{ + off(); + if (length <= 0) + return; + safe_udelay(length); +} + +static void rbwrite(int l) +{ + if (lirc_buffer_full(&rbuf)) { + /* no new signals will be accepted */ + dprintk("Buffer overrun\n"); + return; + } + lirc_buffer_write(&rbuf, (void *)&l); +} + +static void frbwrite(int l) +{ + /* simple noise filter */ + static int pulse, space; + static unsigned int ptr; + + if (ptr > 0 && (l & PULSE_BIT)) { + pulse += l & PULSE_MASK; + if (pulse > 250) { + rbwrite(space); + rbwrite(pulse | PULSE_BIT); + ptr = 0; + pulse = 0; + } + return; + } + if (!(l & PULSE_BIT)) { + if (ptr == 0) { + if (l > 20000) { + space = l; + ptr++; + return; + } + } else { + if (l > 20000) { + space += pulse; + if (space > PULSE_MASK) + space = PULSE_MASK; + space += l; + if (space > PULSE_MASK) + space = PULSE_MASK; + pulse = 0; + return; + } + rbwrite(space); + rbwrite(pulse | PULSE_BIT); + ptr = 0; + pulse = 0; + } + } + rbwrite(l); +} + +static irqreturn_t irq_handler(int i, void *blah) +{ + struct timeval tv; + int counter, dcd; + u8 status; + long deltv; + int data; + static int last_dcd = -1; + + if ((sinp(UART_IIR) & UART_IIR_NO_INT)) { + /* not our interrupt */ + return IRQ_NONE; + } + + counter = 0; + do { + counter++; + status = sinp(UART_MSR); + if (counter > RS_ISR_PASS_LIMIT) { + printk(KERN_WARNING LIRC_DRIVER_NAME ": AIEEEE: " + "We're caught!\n"); + break; + } + if ((status & hardware[type].signal_pin_change) + && sense != -1) { + /* get current time */ + do_gettimeofday(&tv); + + /* New mode, written by Trent Piepho + . */ + + /* + * The old format was not very portable. + * We now use an int to pass pulses + * and spaces to user space. + * + * If PULSE_BIT is set a pulse has been + * received, otherwise a space has been + * received. The driver needs to know if your + * receiver is active high or active low, or + * the space/pulse sense could be + * inverted. The bits denoted by PULSE_MASK are + * the length in microseconds. Lengths greater + * than or equal to 16 seconds are clamped to + * PULSE_MASK. All other bits are unused. + * This is a much simpler interface for user + * programs, as well as eliminating "out of + * phase" errors with space/pulse + * autodetection. + */ + + /* calc time since last interrupt in microseconds */ + dcd = (status & hardware[type].signal_pin) ? 1 : 0; + + if (dcd == last_dcd) { + printk(KERN_WARNING LIRC_DRIVER_NAME + ": ignoring spike: %d %d %lx %lx %lx %lx\n", + dcd, sense, + tv.tv_sec, lasttv.tv_sec, + tv.tv_usec, lasttv.tv_usec); + continue; + } + + deltv = tv.tv_sec-lasttv.tv_sec; + if (tv.tv_sec < lasttv.tv_sec || + (tv.tv_sec == lasttv.tv_sec && + tv.tv_usec < lasttv.tv_usec)) { + printk(KERN_WARNING LIRC_DRIVER_NAME + ": AIEEEE: your clock just jumped " + "backwards\n"); + printk(KERN_WARNING LIRC_DRIVER_NAME + ": %d %d %lx %lx %lx %lx\n", + dcd, sense, + tv.tv_sec, lasttv.tv_sec, + tv.tv_usec, lasttv.tv_usec); + data = PULSE_MASK; + } else if (deltv > 15) { + data = PULSE_MASK; /* really long time */ + if (!(dcd^sense)) { + /* sanity check */ + printk(KERN_WARNING LIRC_DRIVER_NAME + ": AIEEEE: " + "%d %d %lx %lx %lx %lx\n", + dcd, sense, + tv.tv_sec, lasttv.tv_sec, + tv.tv_usec, lasttv.tv_usec); + /* + * detecting pulse while this + * MUST be a space! + */ + sense = sense ? 0 : 1; + } + } else + data = (int) (deltv*1000000 + + tv.tv_usec - + lasttv.tv_usec); + frbwrite(dcd^sense ? data : (data|PULSE_BIT)); + lasttv = tv; + last_dcd = dcd; + wake_up_interruptible(&rbuf.wait_poll); + } + } while (!(sinp(UART_IIR) & UART_IIR_NO_INT)); /* still pending ? */ + return IRQ_HANDLED; +} + + +static int hardware_init_port(void) +{ + u8 scratch, scratch2, scratch3; + + /* + * This is a simple port existence test, borrowed from the autoconfig + * function in drivers/serial/8250.c + */ + scratch = sinp(UART_IER); + soutp(UART_IER, 0); +#ifdef __i386__ + outb(0xff, 0x080); +#endif + scratch2 = sinp(UART_IER) & 0x0f; + soutp(UART_IER, 0x0f); +#ifdef __i386__ + outb(0x00, 0x080); +#endif + scratch3 = sinp(UART_IER) & 0x0f; + soutp(UART_IER, scratch); + if (scratch2 != 0 || scratch3 != 0x0f) { + /* we fail, there's nothing here */ + printk(KERN_ERR LIRC_DRIVER_NAME ": port existence test " + "failed, cannot continue\n"); + return -EINVAL; + } + + + + /* Set DLAB 0. */ + soutp(UART_LCR, sinp(UART_LCR) & (~UART_LCR_DLAB)); + + /* First of all, disable all interrupts */ + soutp(UART_IER, sinp(UART_IER) & + (~(UART_IER_MSI|UART_IER_RLSI|UART_IER_THRI|UART_IER_RDI))); + + /* Clear registers. */ + sinp(UART_LSR); + sinp(UART_RX); + sinp(UART_IIR); + sinp(UART_MSR); + +#ifdef CONFIG_LIRC_SERIAL_NSLU2 + if (type == LIRC_NSLU2) { + /* Setup NSLU2 UART */ + + /* Enable UART */ + soutp(UART_IER, sinp(UART_IER) | UART_IE_IXP42X_UUE); + /* Disable Receiver data Time out interrupt */ + soutp(UART_IER, sinp(UART_IER) & ~UART_IE_IXP42X_RTOIE); + /* set out2 = interrupt unmask; off() doesn't set MCR + on NSLU2 */ + soutp(UART_MCR, UART_MCR_RTS|UART_MCR_OUT2); + } +#endif + + /* Set line for power source */ + off(); + + /* Clear registers again to be sure. */ + sinp(UART_LSR); + sinp(UART_RX); + sinp(UART_IIR); + sinp(UART_MSR); + + switch (type) { + case LIRC_IRDEO: + case LIRC_IRDEO_REMOTE: + /* setup port to 7N1 @ 115200 Baud */ + /* 7N1+start = 9 bits at 115200 ~ 3 bits at 38kHz */ + + /* Set DLAB 1. */ + soutp(UART_LCR, sinp(UART_LCR) | UART_LCR_DLAB); + /* Set divisor to 1 => 115200 Baud */ + soutp(UART_DLM, 0); + soutp(UART_DLL, 1); + /* Set DLAB 0 + 7N1 */ + soutp(UART_LCR, UART_LCR_WLEN7); + /* THR interrupt already disabled at this point */ + break; + default: + break; + } + + return 0; +} + +static int init_port(void) +{ + int i, nlow, nhigh; + + /* Reserve io region. */ + /* + * Future MMAP-Developers: Attention! + * For memory mapped I/O you *might* need to use ioremap() first, + * for the NSLU2 it's done in boot code. + */ + if (((iommap != 0) + && (request_mem_region(iommap, 8 << ioshift, + LIRC_DRIVER_NAME) == NULL)) + || ((iommap == 0) + && (request_region(io, 8, LIRC_DRIVER_NAME) == NULL))) { + printk(KERN_ERR LIRC_DRIVER_NAME + ": port %04x already in use\n", io); + printk(KERN_WARNING LIRC_DRIVER_NAME + ": use 'setserial /dev/ttySX uart none'\n"); + printk(KERN_WARNING LIRC_DRIVER_NAME + ": or compile the serial port driver as module and\n"); + printk(KERN_WARNING LIRC_DRIVER_NAME + ": make sure this module is loaded first\n"); + return -EBUSY; + } + + if (hardware_init_port() < 0) + return -EINVAL; + + /* Initialize pulse/space widths */ + init_timing_params(duty_cycle, freq); + + /* If pin is high, then this must be an active low receiver. */ + if (sense == -1) { + /* wait 1/2 sec for the power supply */ + msleep(500); + + /* + * probe 9 times every 0.04s, collect "votes" for + * active high/low + */ + nlow = 0; + nhigh = 0; + for (i = 0; i < 9; i++) { + if (sinp(UART_MSR) & hardware[type].signal_pin) + nlow++; + else + nhigh++; + msleep(40); + } + sense = (nlow >= nhigh ? 1 : 0); + printk(KERN_INFO LIRC_DRIVER_NAME ": auto-detected active " + "%s receiver\n", sense ? "low" : "high"); + } else + printk(KERN_INFO LIRC_DRIVER_NAME ": Manually using active " + "%s receiver\n", sense ? "low" : "high"); + + return 0; +} + +static int set_use_inc(void *data) +{ + int result; + unsigned long flags; + + /* initialize timestamp */ + do_gettimeofday(&lasttv); + + result = request_irq(irq, irq_handler, + IRQF_DISABLED | (share_irq ? IRQF_SHARED : 0), + LIRC_DRIVER_NAME, (void *)&hardware); + + switch (result) { + case -EBUSY: + printk(KERN_ERR LIRC_DRIVER_NAME ": IRQ %d busy\n", irq); + return -EBUSY; + case -EINVAL: + printk(KERN_ERR LIRC_DRIVER_NAME + ": Bad irq number or handler\n"); + return -EINVAL; + default: + dprintk("Interrupt %d, port %04x obtained\n", irq, io); + break; + }; + + spin_lock_irqsave(&hardware[type].lock, flags); + + /* Set DLAB 0. */ + soutp(UART_LCR, sinp(UART_LCR) & (~UART_LCR_DLAB)); + + soutp(UART_IER, sinp(UART_IER)|UART_IER_MSI); + + spin_unlock_irqrestore(&hardware[type].lock, flags); + + return 0; +} + +static void set_use_dec(void *data) +{ unsigned long flags; + + spin_lock_irqsave(&hardware[type].lock, flags); + + /* Set DLAB 0. */ + soutp(UART_LCR, sinp(UART_LCR) & (~UART_LCR_DLAB)); + + /* First of all, disable all interrupts */ + soutp(UART_IER, sinp(UART_IER) & + (~(UART_IER_MSI|UART_IER_RLSI|UART_IER_THRI|UART_IER_RDI))); + spin_unlock_irqrestore(&hardware[type].lock, flags); + + free_irq(irq, (void *)&hardware); + + dprintk("freed IRQ %d\n", irq); +} + +static ssize_t lirc_write(struct file *file, const char *buf, + size_t n, loff_t *ppos) +{ + int i, count; + unsigned long flags; + long delta = 0; + int *wbuf; + + if (!(hardware[type].features & LIRC_CAN_SEND_PULSE)) + return -EBADF; + + count = n / sizeof(int); + if (n % sizeof(int) || count % 2 == 0) + return -EINVAL; + wbuf = memdup_user(buf, n); + if (PTR_ERR(wbuf)) + return PTR_ERR(wbuf); + spin_lock_irqsave(&hardware[type].lock, flags); + if (type == LIRC_IRDEO) { + /* DTR, RTS down */ + on(); + } + for (i = 0; i < count; i++) { + if (i%2) + hardware[type].send_space(wbuf[i] - delta); + else + delta = hardware[type].send_pulse(wbuf[i]); + } + off(); + spin_unlock_irqrestore(&hardware[type].lock, flags); + return n; +} + +static long lirc_ioctl(struct file *filep, unsigned int cmd, unsigned long arg) +{ + int result; + unsigned long value; + unsigned int ivalue; + + switch (cmd) { + case LIRC_GET_SEND_MODE: + if (!(hardware[type].features&LIRC_CAN_SEND_MASK)) + return -ENOIOCTLCMD; + + result = put_user(LIRC_SEND2MODE + (hardware[type].features&LIRC_CAN_SEND_MASK), + (unsigned long *) arg); + if (result) + return result; + break; + + case LIRC_SET_SEND_MODE: + if (!(hardware[type].features&LIRC_CAN_SEND_MASK)) + return -ENOIOCTLCMD; + + result = get_user(value, (unsigned long *) arg); + if (result) + return result; + /* only LIRC_MODE_PULSE supported */ + if (value != LIRC_MODE_PULSE) + return -ENOSYS; + break; + + case LIRC_GET_LENGTH: + return -ENOSYS; + break; + + case LIRC_SET_SEND_DUTY_CYCLE: + dprintk("SET_SEND_DUTY_CYCLE\n"); + if (!(hardware[type].features&LIRC_CAN_SET_SEND_DUTY_CYCLE)) + return -ENOIOCTLCMD; + + result = get_user(ivalue, (unsigned int *) arg); + if (result) + return result; + if (ivalue <= 0 || ivalue > 100) + return -EINVAL; + return init_timing_params(ivalue, freq); + break; + + case LIRC_SET_SEND_CARRIER: + dprintk("SET_SEND_CARRIER\n"); + if (!(hardware[type].features&LIRC_CAN_SET_SEND_CARRIER)) + return -ENOIOCTLCMD; + + result = get_user(ivalue, (unsigned int *) arg); + if (result) + return result; + if (ivalue > 500000 || ivalue < 20000) + return -EINVAL; + return init_timing_params(duty_cycle, ivalue); + break; + + default: + return lirc_dev_fop_ioctl(filep, cmd, arg); + } + return 0; +} + +static struct file_operations lirc_fops = { + .owner = THIS_MODULE, + .write = lirc_write, + .unlocked_ioctl = lirc_ioctl, + .read = lirc_dev_fop_read, + .poll = lirc_dev_fop_poll, + .open = lirc_dev_fop_open, + .release = lirc_dev_fop_close, +}; + +static struct lirc_driver driver = { + .name = LIRC_DRIVER_NAME, + .minor = -1, + .code_length = 1, + .sample_rate = 0, + .data = NULL, + .add_to_buf = NULL, + .rbuf = &rbuf, + .set_use_inc = set_use_inc, + .set_use_dec = set_use_dec, + .fops = &lirc_fops, + .dev = NULL, + .owner = THIS_MODULE, +}; + +static struct platform_device *lirc_serial_dev; + +static int __devinit lirc_serial_probe(struct platform_device *dev) +{ + return 0; +} + +static int __devexit lirc_serial_remove(struct platform_device *dev) +{ + return 0; +} + +static int lirc_serial_suspend(struct platform_device *dev, + pm_message_t state) +{ + /* Set DLAB 0. */ + soutp(UART_LCR, sinp(UART_LCR) & (~UART_LCR_DLAB)); + + /* Disable all interrupts */ + soutp(UART_IER, sinp(UART_IER) & + (~(UART_IER_MSI|UART_IER_RLSI|UART_IER_THRI|UART_IER_RDI))); + + /* Clear registers. */ + sinp(UART_LSR); + sinp(UART_RX); + sinp(UART_IIR); + sinp(UART_MSR); + + return 0; +} + +/* twisty maze... need a forward-declaration here... */ +static void lirc_serial_exit(void); + +static int lirc_serial_resume(struct platform_device *dev) +{ + unsigned long flags; + + if (hardware_init_port() < 0) { + lirc_serial_exit(); + return -EINVAL; + } + + spin_lock_irqsave(&hardware[type].lock, flags); + /* Enable Interrupt */ + do_gettimeofday(&lasttv); + soutp(UART_IER, sinp(UART_IER)|UART_IER_MSI); + off(); + + lirc_buffer_clear(&rbuf); + + spin_unlock_irqrestore(&hardware[type].lock, flags); + + return 0; +} + +static struct platform_driver lirc_serial_driver = { + .probe = lirc_serial_probe, + .remove = __devexit_p(lirc_serial_remove), + .suspend = lirc_serial_suspend, + .resume = lirc_serial_resume, + .driver = { + .name = "lirc_serial", + .owner = THIS_MODULE, + }, +}; + +static int __init lirc_serial_init(void) +{ + int result; + + /* Init read buffer. */ + result = lirc_buffer_init(&rbuf, sizeof(int), RBUF_LEN); + if (result < 0) + return -ENOMEM; + + result = platform_driver_register(&lirc_serial_driver); + if (result) { + printk("lirc register returned %d\n", result); + goto exit_buffer_free; + } + + lirc_serial_dev = platform_device_alloc("lirc_serial", 0); + if (!lirc_serial_dev) { + result = -ENOMEM; + goto exit_driver_unregister; + } + + result = platform_device_add(lirc_serial_dev); + if (result) + goto exit_device_put; + + return 0; + +exit_device_put: + platform_device_put(lirc_serial_dev); +exit_driver_unregister: + platform_driver_unregister(&lirc_serial_driver); +exit_buffer_free: + lirc_buffer_free(&rbuf); + return result; +} + +static void lirc_serial_exit(void) +{ + platform_device_unregister(lirc_serial_dev); + platform_driver_unregister(&lirc_serial_driver); + lirc_buffer_free(&rbuf); +} + +static int __init lirc_serial_init_module(void) +{ + int result; + + result = lirc_serial_init(); + if (result) + return result; + + switch (type) { + case LIRC_HOMEBREW: + case LIRC_IRDEO: + case LIRC_IRDEO_REMOTE: + case LIRC_ANIMAX: + case LIRC_IGOR: + /* if nothing specified, use ttyS0/com1 and irq 4 */ + io = io ? io : 0x3f8; + irq = irq ? irq : 4; + break; +#ifdef CONFIG_LIRC_SERIAL_NSLU2 + case LIRC_NSLU2: + io = io ? io : IRQ_IXP4XX_UART2; + irq = irq ? irq : (IXP4XX_UART2_BASE_VIRT + REG_OFFSET); + iommap = iommap ? iommap : IXP4XX_UART2_BASE_PHYS; + ioshift = ioshift ? ioshift : 2; + break; +#endif + default: + result = -EINVAL; + goto exit_serial_exit; + } + if (!softcarrier) { + switch (type) { + case LIRC_HOMEBREW: + case LIRC_IGOR: +#ifdef CONFIG_LIRC_SERIAL_NSLU2 + case LIRC_NSLU2: +#endif + hardware[type].features &= + ~(LIRC_CAN_SET_SEND_DUTY_CYCLE| + LIRC_CAN_SET_SEND_CARRIER); + break; + } + } + + result = init_port(); + if (result < 0) + goto exit_serial_exit; + driver.features = hardware[type].features; + driver.dev = &lirc_serial_dev->dev; + driver.minor = lirc_register_driver(&driver); + if (driver.minor < 0) { + printk(KERN_ERR LIRC_DRIVER_NAME + ": register_chrdev failed!\n"); + result = -EIO; + goto exit_release; + } + return 0; +exit_release: + release_region(io, 8); +exit_serial_exit: + lirc_serial_exit(); + return result; +} + +static void __exit lirc_serial_exit_module(void) +{ + lirc_serial_exit(); + if (iommap != 0) + release_mem_region(iommap, 8 << ioshift); + else + release_region(io, 8); + lirc_unregister_driver(driver.minor); + dprintk("cleaned up module\n"); +} + + +module_init(lirc_serial_init_module); +module_exit(lirc_serial_exit_module); + +MODULE_DESCRIPTION("Infra-red receiver driver for serial ports."); +MODULE_AUTHOR("Ralph Metzler, Trent Piepho, Ben Pfaff, " + "Christoph Bartelmus, Andrei Tanas"); +MODULE_LICENSE("GPL"); + +module_param(type, int, S_IRUGO); +MODULE_PARM_DESC(type, "Hardware type (0 = home-brew, 1 = IRdeo," + " 2 = IRdeo Remote, 3 = AnimaX, 4 = IgorPlug," + " 5 = NSLU2 RX:CTS2/TX:GreenLED)"); + +module_param(io, int, S_IRUGO); +MODULE_PARM_DESC(io, "I/O address base (0x3f8 or 0x2f8)"); + +/* some architectures (e.g. intel xscale) have memory mapped registers */ +module_param(iommap, bool, S_IRUGO); +MODULE_PARM_DESC(iommap, "physical base for memory mapped I/O" + " (0 = no memory mapped io)"); + +/* + * some architectures (e.g. intel xscale) align the 8bit serial registers + * on 32bit word boundaries. + * See linux-kernel/serial/8250.c serial_in()/out() + */ +module_param(ioshift, int, S_IRUGO); +MODULE_PARM_DESC(ioshift, "shift I/O register offset (0 = no shift)"); + +module_param(irq, int, S_IRUGO); +MODULE_PARM_DESC(irq, "Interrupt (4 or 3)"); + +module_param(share_irq, bool, S_IRUGO); +MODULE_PARM_DESC(share_irq, "Share interrupts (0 = off, 1 = on)"); + +module_param(sense, bool, S_IRUGO); +MODULE_PARM_DESC(sense, "Override autodetection of IR receiver circuit" + " (0 = active high, 1 = active low )"); + +#ifdef CONFIG_LIRC_SERIAL_TRANSMITTER +module_param(txsense, bool, S_IRUGO); +MODULE_PARM_DESC(txsense, "Sense of transmitter circuit" + " (0 = active high, 1 = active low )"); +#endif + +module_param(softcarrier, bool, S_IRUGO); +MODULE_PARM_DESC(softcarrier, "Software carrier (0 = off, 1 = on, default on)"); + +module_param(debug, bool, S_IRUGO | S_IWUSR); +MODULE_PARM_DESC(debug, "Enable debugging messages");