From 18847b42f8d157201550015296a222a9009a04da Mon Sep 17 00:00:00 2001 From: Javier Martin Date: Fri, 1 Jun 2012 09:45:33 +0200 Subject: [PATCH] ARM i.MX27 Visstrim M10: fix gpio handling. Some GPIOs in Visstrim M10 are used without being registered. This leads to USB and video malfunctions. This patch registers those GPIOs to solve the issue. Signed-off-by: Javier Martin Signed-off-by: Sascha Hauer --- arch/arm/mach-imx/mach-imx27_visstrim_m10.c | 36 ++++++++++++++------- 1 file changed, 25 insertions(+), 11 deletions(-) diff --git a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c index f7b074f496f0..2c6a783d4c04 100644 --- a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c +++ b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c @@ -107,6 +107,8 @@ static const int visstrim_m10_pins[] __initconst = { PB23_PF_USB_PWR, PB24_PF_USB_OC, /* CSI */ + TVP5150_RSTN | GPIO_GPIO | GPIO_OUT, + TVP5150_PWDN | GPIO_GPIO | GPIO_OUT, PB10_PF_CSI_D0, PB11_PF_CSI_D1, PB12_PF_CSI_D2, @@ -121,6 +123,24 @@ static const int visstrim_m10_pins[] __initconst = { PB21_PF_CSI_HSYNC, }; +static const struct gpio visstrim_m10_gpios[] __initconst = { + { + .gpio = TVP5150_RSTN, + .flags = GPIOF_DIR_OUT | GPIOF_INIT_HIGH, + .label = "tvp5150_rstn", + }, + { + .gpio = TVP5150_PWDN, + .flags = GPIOF_DIR_OUT | GPIOF_INIT_LOW, + .label = "tvp5150_pwdn", + }, + { + .gpio = OTG_PHY_CS_GPIO, + .flags = GPIOF_DIR_OUT | GPIOF_INIT_LOW, + .label = "usbotg_cs", + }, +}; + /* Camera */ static int visstrim_camera_power(struct device *dev, int on) { @@ -164,13 +184,6 @@ static void __init visstrim_camera_init(void) struct platform_device *pdev; int dma; - /* Initialize tvp5150 gpios */ - mxc_gpio_mode(TVP5150_RSTN | GPIO_GPIO | GPIO_OUT); - mxc_gpio_mode(TVP5150_PWDN | GPIO_GPIO | GPIO_OUT); - gpio_set_value(TVP5150_RSTN, 1); - gpio_set_value(TVP5150_PWDN, 0); - ndelay(1); - gpio_set_value(TVP5150_PWDN, 1); ndelay(1); gpio_set_value(TVP5150_RSTN, 0); @@ -351,10 +364,6 @@ static struct i2c_board_info visstrim_m10_i2c_devices[] = { /* USB OTG */ static int otg_phy_init(struct platform_device *pdev) { - gpio_set_value(OTG_PHY_CS_GPIO, 0); - - mdelay(10); - return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED); } @@ -380,6 +389,11 @@ static void __init visstrim_m10_board_init(void) if (ret) pr_err("Failed to setup pins (%d)\n", ret); + ret = gpio_request_array(visstrim_m10_gpios, + ARRAY_SIZE(visstrim_m10_gpios)); + if (ret) + pr_err("Failed to request gpios (%d)\n", ret); + imx27_add_imx_ssi(0, &visstrim_m10_ssi_pdata); imx27_add_imx_uart0(&uart_pdata); -- GitLab