提交 16c79a04 编写于 作者: S Steve Glendinning 提交者: David S. Miller

smsc75xx: enable power saving mode during system suspend

This patch instructs the device to enter its lowest power SUSPEND2
state during system suspend.

This patch also explicitly wakes the device after resume, which
should address reports of the device not automatically coming
back after system suspend:

Patch updated to change BUG_ON to WARN_ON_ONCE.

http://code.google.com/p/chromium-os/issues/detail?id=31871Signed-off-by: NSteve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 8762cec8
......@@ -1106,6 +1106,57 @@ static void smsc75xx_unbind(struct usbnet *dev, struct usb_interface *intf)
}
}
static int smsc75xx_suspend(struct usb_interface *intf, pm_message_t message)
{
struct usbnet *dev = usb_get_intfdata(intf);
int ret;
u32 val;
if (WARN_ON_ONCE(!dev))
return -EINVAL;
ret = usbnet_suspend(intf, message);
check_warn_return(ret, "usbnet_suspend error");
netdev_info(dev->net, "entering SUSPEND2 mode");
ret = smsc75xx_read_reg(dev, PMT_CTL, &val);
check_warn_return(ret, "Error reading PMT_CTL");
val &= ~(PMT_CTL_SUS_MODE | PMT_CTL_WUPS | PMT_CTL_PHY_RST);
val |= PMT_CTL_SUS_MODE_2;
ret = smsc75xx_write_reg(dev, PMT_CTL, val);
check_warn_return(ret, "Error writing PMT_CTL");
return 0;
}
static int smsc75xx_resume(struct usb_interface *intf)
{
struct usbnet *dev = usb_get_intfdata(intf);
int ret;
u32 val;
if (WARN_ON_ONCE(!dev))
return -EINVAL;
netdev_info(dev->net, "resuming from SUSPEND2");
ret = smsc75xx_read_reg(dev, PMT_CTL, &val);
check_warn_return(ret, "Error reading PMT_CTL");
val |= PMT_CTL_PHY_PWRUP;
ret = smsc75xx_write_reg(dev, PMT_CTL, val);
check_warn_return(ret, "Error writing PMT_CTL");
ret = smsc75xx_wait_ready(dev);
check_warn_return(ret, "device not ready in smsc75xx_resume");
return usbnet_resume(intf);
}
static void smsc75xx_rx_csum_offload(struct usbnet *dev, struct sk_buff *skb,
u32 rx_cmd_a, u32 rx_cmd_b)
{
......@@ -1274,9 +1325,9 @@ static struct usb_driver smsc75xx_driver = {
.name = SMSC_CHIPNAME,
.id_table = products,
.probe = usbnet_probe,
.suspend = usbnet_suspend,
.resume = usbnet_resume,
.reset_resume = usbnet_resume,
.suspend = smsc75xx_suspend,
.resume = smsc75xx_resume,
.reset_resume = smsc75xx_resume,
.disconnect = usbnet_disconnect,
.disable_hub_initiated_lpm = 1,
};
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册