menu "Hardware Drivers Config"

config SOC_STM32F407ZG
    bool
    select SOC_SERIES_STM32F4
    default y

menu "Onboard Peripheral Drivers"

    config BSP_USING_USB_TO_USART
        bool "Enable USB TO USART (uart1)"
        select BSP_USING_UART
        select BSP_USING_UART1
        default y

    config BSP_USING_COM2
        bool "Enable COM2 (uart2 pin conflict with Ethernet and PWM)"
        select BSP_USING_UART
        select BSP_USING_UART2
        default n

    config BSP_USING_COM3
        bool "Enable COM3 (uart3)"
        select BSP_USING_UART
        select BSP_USING_UART3
        default n

    config BSP_USING_SPI_FLASH
        bool "Enable SPI FLASH (W25Q128 spi1)"
        select BSP_USING_SPI
        select BSP_USING_SPI1
        select RT_USING_SFUD
        select RT_SFUD_USING_SFDP
        default n

    config BSP_USING_EEPROM
        bool "Enable I2C EEPROM (i2c1)"
        select BSP_USING_I2C1
        default n

    config PHY_USING_LAN8720A
        bool
    
    config BSP_USING_ETH
        bool "Enable Ethernet"
        default n
        select RT_USING_LWIP
        select PHY_USING_LAN8720A

    config BSP_USING_MPU6050
        bool "Enable MPU6050 (i2c1)"
        default n
        select BSP_USING_I2C1
        select PKG_USING_MPU6XXX

    config BSP_USING_SDCARD
        bool "Enable SDCARD (sdio)"
        select BSP_USING_SDIO
        select RT_USING_DFS
        select RT_USING_DFS_ELMFAT
        default n

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default y

            config BSP_UART1_RX_USING_DMA
                bool "Enable UART1 RX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART3
                bool "Enable UART3"
                default n

            config BSP_UART3_RX_USING_DMA
                bool "Enable UART3 RX DMA"
                depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
                default n
        endif

    menuconfig BSP_USING_TIM
        bool "Enable timer"
        default n
        select RT_USING_HWTIMER
        if BSP_USING_TIM
            config BSP_USING_TIM11
                bool "Enable TIM11"
                default n

            config BSP_USING_TIM13
                bool "Enable TIM13"
                default n

            config BSP_USING_TIM14
                bool "Enable TIM14"
                default n
        endif

    menuconfig BSP_USING_PWM
        bool "Enable pwm"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM2
            bool "Enable timer2 output pwm"
            default n
            if BSP_USING_PWM2
                config BSP_USING_PWM2_CH4
                    bool "Enable PWM2 channel4"
                    default n
            endif
        endif

    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n

    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI1
                bool "Enable SPI1 BUS"
                default n

            config BSP_SPI1_TX_USING_DMA
                bool "Enable SPI1 TX DMA"
                depends on BSP_USING_SPI1
                default n
                
            config BSP_SPI1_RX_USING_DMA
                bool "Enable SPI1 RX DMA"
                depends on BSP_USING_SPI1
                select BSP_SPI1_TX_USING_DMA
                default n

            config BSP_USING_SPI2
                bool "Enable SPI2 BUS"
                default n

            config BSP_SPI2_TX_USING_DMA
                bool "Enable SPI2 TX DMA"
                depends on BSP_USING_SPI2
                default n
                
            config BSP_SPI2_RX_USING_DMA
                bool "Enable SPI2 RX DMA"
                depends on BSP_USING_SPI2
                select BSP_SPI2_TX_USING_DMA
                default n
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif

    menuconfig BSP_USING_I2C1
        bool "Enable I2C1 BUS (software simulation)"
        default y
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C1
            config BSP_I2C1_SCL_PIN
                int "i2c1 scl pin number"
                range 0 143
                default 24
            config BSP_I2C1_SDA_PIN
                int "I2C1 sda pin number"
                range 0 143
                default 25
        endif

    config BSP_USING_ONCHIP_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        select RT_USING_LIBC
        default n

    config BSP_USING_WDT
        bool "Enable Watchdog Timer"
        select RT_USING_WDT
        default n

    config BSP_USING_SDIO
        bool "Enable SDIO"
        select RT_USING_SDIO
        select RT_USING_DFS
        default n

endmenu

menu "Board extended module Drivers"

endmenu

endmenu