This patch (as1135) essentially reverts the major parts of two earlier
patches to usbcore, because they ended up causing a regression.

Trying to recover from transient communication errors can lead to
other problems, because operations that failed during the error period
are not always retried.  The simplest example is the initial
Set-Config request sent after device enumeration; if it gets lost then
it will not be retried and the device will remain unconfigured.

This patch restores the old behavior in which any port disconnect or
port disable causes the entire device structure to be removed, fixing a
reported regression.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NFrans Pop <elendil@planet.nl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Nokia 5310 Music Xpress phone reports one too many sectors in
usb-storage mode.  This patch resolves that.
Signed-off-by: NDavid Almaroad <dalmaroad@gmail.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Support for Domintell devices (FTDI FT232BM based) : DGQG and DUSB01
module.  PIDs were missing.
Signed-off-by: NGaetan Carlier <gcpatch@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In file included from drivers/usb/musb/musb_core.h:59,
                 from drivers/usb/musb/musb_core.c:108:
drivers/usb/musb/musb_io.h:42: error: conflicting types for '__raw_readsl'
/usr/src/devel/arch/sh/include/asm/io.h:112: error: previous declaration of '__raw_readsl' was here
drivers/usb/musb/musb_io.h:42: error: conflicting types for '__raw_readsl'
/usr/src/devel/arch/sh/include/asm/io.h:112: error: previous declaration of '__raw_readsl' was here
drivers/usb/musb/musb_io.h:44: error: conflicting types for 'readsw'
/usr/src/devel/arch/sh/include/asm/io.h:164: error: previous definition of 'readsw' was here
drivers/usb/musb/musb_io.h:46: error: conflicting types for 'readsb'
/usr/src/devel/arch/sh/include/asm/io.h:163: error: previous definition of 'readsb' was here
drivers/usb/musb/musb_io.h:49: error: conflicting types for '__raw_writesl'
/usr/src/devel/arch/sh/include/asm/io.h:111: error: previous declaration of '__raw_writesl' was here
drivers/usb/musb/musb_io.h:49: error: conflicting types for '__raw_writesl'
/usr/src/devel/arch/sh/include/asm/io.h:111: error: previous declaration of '__raw_writesl' was here
drivers/usb/musb/musb_io.h:51: error: conflicting types for 'writesw'
/usr/src/devel/arch/sh/include/asm/io.h:164: error: previous definition of 'writesw' was here
drivers/usb/musb/musb_io.h:53: error: conflicting types for 'writesb'
/usr/src/devel/arch/sh/include/asm/io.h:163: error: previous definition of 'writesb' was here

Cc: Karsten Keil <kkeil@suse.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add another MC8785 VID/PID
Signed-off-by: NKevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB: ftdi_sio: Add 0x5050/0x0900 USB IDs (Papouch Quido USB 4/4)
Signed-off-by: NJaroslav Kysela <perex@perex.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

While making some other changes to ti_usb_3410_5052, I noticed that the
changes made to move the firmware loading to a separate function are
broken (in ti_download_firmware(), status is set to -ENOMEM and never
changed).  This means the driver will never initialize the device
properly.  It looks like status was supposed to get the result of
ti_do_download().
Signed-off-by: NChris Adams <cmadams@hiwaay.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes:
drivers/usb/gadget/fsl_usb2_udc.c: In function 'dr_controller_setup':
drivers/usb/gadget/fsl_usb2_udc.c:229: warning: format '%p' expects type
'void *', but argument 3 has type 'int'
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1136) adds an unusual_devs entry for a version of the
RockChip MP3 player which can't handle the MODE SENSE command used for
write-protect detection.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NCraig Shelley <craig@microtron.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This hardware needs the pl2303 hack in order to work properly :(
Signed-off-by: NAndreas Bombe <aeb@debian.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As noted by Stefan Neis <Stefan.Neis@kobil.com>, we had a recent
regression with EHCI periodic transfers, in some (seemingly not
all that common) cases.

The root cause was that the schedule activation was only loosely
coupled to the addition or removal of transfers, so two different
execution contexts could both think they had to deactivate (or
conversely activate) the schedule.  So this fix tightens that
coupling, managing it more like a refcount.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

headers were moved, fixing.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I had trouble connecting my cell phone as a storage device - so I added
it to the unusual_devs.h list. I had trouble with the bcdDeviceMin and
Max values - so after some experimenting I made it pretty inclusive.

From: Filip Joelsson <filip@blueturtle.nu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This resolves another regression caused by the "use omap_read/write
instead of __REG" patch:  the hardware address used for DMA to/from
the UDC became wrong.  Bug noted by Russell King.
Reported-by: NRussell King <rmk@arm.linux.org.uk>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NRussell King <rmk@arm.linux.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The extended anchor API is documented
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit de85422b, 'USB: fix interrupt
disabling for HCDs with shared interrupt handlers' changed usb_add_hcd()
to strip IRQF_DISABLED from irqflags prior to calling request_irq()
with the justification that such a removal was necessary for shared
interrupts to work properly.  Unfortunately, the change in that commit
unconditionally removes the IRQF_DISABLED flag, causing problems on
platforms that don't use a shared interrupt but require IRQF_DISABLED.
This change adds a check for IRQF_SHARED prior to removing the
IRQF_DISABLED flag.

Fixes the PS3 system startup hang reported with recent Fedora and
OpenSUSE kernels.

Note that this problem is hidden when CONFIG_LOCKDEP=y (ps3_defconfig),
as local_irq_enable_in_hardirq() is defined as a null statement for
that config.

CC: stable <stable@kernel.org>
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Stefan Becker <Stefan.Becker@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I was trying to figure out why my device wasn't supported by the
drivers/usb/serial/sierra.c driver, while looking throught the device
IDs I spotted what I believe to be a typo in the device IDs.  Please
apply the following patch

If you look down further, there is another HP wireless broadband card,
which has a vendor ID of 03f0, like my device.  Below is my "lsusb -v
-d 03f0:1b1d".

Bus 001 Device 005: ID 03f0:1b1d Hewlett-Packard
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x03f0 Hewlett-Packard
  idProduct          0x1b1d
  bcdDevice            0.01
  iManufacturer           1 HP
  iProduct                2 HP ev2200 1xEV-DO Broadband Wireless Module
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           67
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           7
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              3 Data Interface
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0010  1x 16 bytes
        bInterval             128
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x84  EP 4 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x04  EP 4 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x85  EP 5 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x05  EP 5 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
Device Status:     0x0000
  (Bus Powered)

From: Tony Murray <murraytony@gmail.com>
Cc: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes that behavior:

...
Aug 26 22:39:23 rnauber sd 2:0:0:0: [sda] Sense Key : 0x0 [current]
Aug 26 22:39:23 rnauber sd 2:0:0:0: [sda] ASC=0x0 ASCQ=0x0
Aug 26 22:39:23 rnauber sd 2:0:0:0: [sda] Sense Key : 0x0 [current]
Aug 26 22:39:23 rnauber sd 2:0:0:0: [sda] ASC=0x0 ASCQ=0x0
Aug 26 22:39:23 rnauber sd 2:0:0:0: [sda] Sense Key : 0x0 [current]
Aug 26 22:39:23 rnauber sd 2:0:0:0: [sda] ASC=0x0 ASCQ=0x0
Aug 26 22:39:23 rnauber sd 2:0:0:0: [sda] Sense Key : 0x0 [current]
...


cat  /proc/bus/usb/devices
...
T:  Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0421 ProdID=04fa Rev= 6.01
S:  Manufacturer=Nokia
S:  Product=Nokia 6300
S:  SerialNumber=35XXXXXXXX
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
...

From: Richard Nauber <RichardNauber@web.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I noticed that the "Refactor "if (handshake()) state = HC_STATE_HALT"
patch from earlier this year perpetuated a potential problem:  it can
mark the controller as halted when it's still running (but not acting
as, perhaps wrongly, expected).

That caused some hangs and crashes, rather than more polite failure
modes of a truly halted controller.  This patch forces a true halt,
and emits a (previously missing) diagnostic.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds devices to the sierra driver and rev's the driver version.
Signed-off-by: NKevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch alters the Sierra Mass Storage patch so that it is non-configurable.
Signed-off-by: NKevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: fix compiler warnings in pci_get_subsys()
  PCI: Fix pcie_aspm=force

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] kexec fails on systems with blocks of uncached memory
  [IA64] Ski simulator doesn't need check_sal_cache_flush

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: ASoC: maintainers - update email address for Liam Girdwood

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] unlocked_ioctl changes
  [WATCHDOG] wdt285: fix sparse warnings
  [WATCHDOG] ibmasr: remove unnecessary spin_unlock()

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix missing devices due to PCI bridge test in of_create_pci_dev().
  sparc64: Fix disappearing PCI devices on e3500.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  ath9k: Fix IRQ nobody cared issue with ath9k
  wireless: zd1211rw: add device ID fix wifi dongle "trust nw-3100"
  ath9k: connectivity is lost after Group rekeying is done

This problem seems to be unnoticed so far:

http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=b3b708fa2780cd2b5d8266a8f0c3a1cab364d4d2

has changed the serial core behavior to not to suspend the port if the
device is enabled as a wakeup source.  If the AT91 system goes to slow
clock mode, the port should be suspended always and the clocks should be
switched off.  The patch attached updates the atmel_serial driver to match
the changes in serial core.

Also, the interrupts are disabled when the clock is disabled.  If we
disable the clock with interrupts enabled, an interrupt may get stuck.  If
this is the DBGU interrupt, this blocks the OR logic at system controller
and thus all other sysc interrupts.
Signed-off-by: NAnti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Michael Trimarchi <trimarchimichael@yahoo.it>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Current memory cgroup(both in mainline and -mm) doesn't account swap
caches as memory(swap cache support is dropped temporarily now).

So try_to_free_mem_cgroup_pages doesn't reflect the count of pages that
have been moved to swap cache.

But this makes mem_cgroup_shrink_usage fail easily if most of the pages
are anon/shmem, and then shmem_getpage returns -ENOMEM and the process
will be killed.

This patch adds res_counter_check_under_limit to avoid these cases.

BTW, even if swap cache support is enabled again, if a process is moved to
another cgroup, which has been just made, between precharge and
shrink_usage in shmem_getpage, shrink_usage may fail just because there is
no pages to reclaim.

So this change would make sense anyway.
Signed-off-by: NDaisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- s/s/seconds/

- s/10 seconds/60 seconds/

- Mention the zero-disables-it feature.

Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

tiny-shmem calls do_truncate in shmem_file_setup.  do_truncate takes
i_mutex, and shmem_file_setup is called with mmap_sem held.  However
i_mutex nests outside mmap_sem.

Copy the code in shmem.c to avoid this problem.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NNick Piggin <npiggin@suse.de>
Reported-and-tested-by: NIngo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The reasons for disabling paccept() are as follows:

* The API is more complex than needed.  There is AFAICS no demonstrated
  use case that the sigset argument of this syscall serves that couldn't
  equally be served by the use of pselect/ppoll/epoll_pwait + traditional
  accept().  Roland seems to concur with this opinion
  (http://thread.gmane.org/gmane.linux.kernel/723953/focus=732255).  I
  have (more than once) asked Ulrich to explain otherwise
  (http://thread.gmane.org/gmane.linux.kernel/723952/focus=731018), but he
  does not respond, so one is left to assume that he doesn't know of such
  a case.

* The use of a sigset argument is not consistent with other I/O APIs
  that can block on a single file descriptor (e.g., read(), recv(),
  connect()).

* The behavior of paccept() when interrupted by a signal is IMO strange:
  the kernel restarts the system call if SA_RESTART was set for the
  handler.  I think that it should not do this -- that it should behave
  consistently with paccept()/ppoll()/epoll_pwait(), which never restart,
  regardless of SA_RESTART.  The reasoning here is that the very purpose
  of paccept() is to wait for a connection or a signal, and that
  restarting in the latter case is probably never useful.  (Note: Roland
  disagrees on this point, believing that rather paccept() should be
  consistent with accept() in its behavior wrt EINTR
  (http://thread.gmane.org/gmane.linux.kernel/723953/focus=732255).)

I believe that instead, a simpler API, consistent with Ulrich's other
recent additions, is preferable:

accept4(int fd, struct sockaddr *sa, socklen_t *salen, ind flags);

(This simpler API was originally proposed by Ulrich:
http://thread.gmane.org/gmane.linux.network/92072)

If this simpler API is added, then if we later decide that the sigset
argument really is required, then a suitable bit in 'flags' could be added
to indicate the presence of the sigset argument.

At this point, I am hoping we either will get a counter-argument from
Ulrich about why we really do need paccept()'s sigset argument, or that he
will resubmit the original accept4() patch.
Signed-off-by: NMichael Kerrisk <mtk.manpages@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Alan Cox <alan@redhat.com>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make the example code consistent with changed API.
Signed-off-by: NMarin Mitov <mitov@ispp.bas.bg>
Acked-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A segmentation fault can occur in kimage_add_entry in kexec.c when loading
a kernel image into memory.  The fault occurs because a page is requested
by calling kimage_alloc_page with gfp_mask GFP_KERNEL and the function may
actually return a page with gfp_mask GFP_HIGHUSER.  The high mem page is
returned because it was swapped with the kernel page due to the kernel
page being a page that will shortly be copied to.

This patch ensures that kimage_alloc_page returns a page that was created
with the correct gfp flags.

I have verified the change and fixed the whitespace damage of the original
patch.  Jonathan did a great job of tracking this down after he hit the
problem.  -- Eric
Signed-off-by: NJonathan Steel <jon.steel@esentire.com>
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Struct members may be marked as private by using
	/* private: */
before them, as noted in Documentation/kernel-doc-nano-HOWTO.txt

Fix kernel-doc to handle structs whose members are all private;
otherwise invalid XML is generated:

xmlto: input does not validate (status 3)
linux-2.6.27-rc6-git4/Documentation/DocBook/debugobjects.xml:146: element variablelist: validity error : Element variablelist content does not follow the DTD, expecting ((title , titleabbrev?)? , varlistentry+), got ()
Document linux-2.6.27-rc6-git4/Documentation/DocBook/debugobjects.xml does not validate
make[1]: *** [Documentation/DocBook/debugobjects.html] Error 3
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Reported-by: NRoland McGrath <roland@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

linux/time.h conflicts with time.h from glibc

It breaks building smbmount from samba.  It's regression introduced by
commit 76308da1 (" smb.h: uses struct timespec but didn't include
linux/time.h").
Signed-off-by: NKirill A. Shutemov <kirill@shutemov.name>
Cc: <stable@kernel.org>             [2.6.26.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__asr_toggle() is always called with asr_lock held.
But there is unnecessary spin_unlock() call in __asr_toggle().
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Acked-by: NAndrey Panin <pazke@donpac.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch updates the maintainers email address for Liam Girdwood and
adds a URL for the ASoC website.
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>