/**************************************************************************//** * @file UART.h * @version V1.00 * $Revision: 7 $ * $Date: 14/02/05 10:27a $ * @brief Mini51 series UART driver header file * * @note * Copyright (C) 2013 Nuvoton Technology Corp. All rights reserved. *****************************************************************************/ #ifndef __UART_H__ #define __UART_H__ #include "M051Series.h" #ifdef __cplusplus extern "C" { #endif /** @addtogroup M051_Device_Driver M051 Device Driver @{ */ /** @addtogroup M051_UART_Driver UART Driver @{ */ /** @addtogroup M051_UART_EXPORTED_CONSTANTS UART Exported Constants @{ */ /*---------------------------------------------------------------------------------------------------------*/ /* UA_FCR constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_FCR_RFITL_1BYTE (0x0 << UART_FCR_RFITL_Pos) /*!< UA_FCR setting to set RX FIFO Trigger Level to 1 bit */ #define UART_FCR_RFITL_4BYTES (0x1 << UART_FCR_RFITL_Pos) /*!< UA_FCR setting to set RX FIFO Trigger Level to 4 bits */ #define UART_FCR_RFITL_8BYTES (0x2 << UART_FCR_RFITL_Pos) /*!< UA_FCR setting to set RX FIFO Trigger Level to 8 bits */ #define UART_FCR_RFITL_14BYTES (0x3 << UART_FCR_RFITL_Pos) /*!< UA_FCR setting to set RX FIFO Trigger Level to 14 bits */ #define UART_FCR_RTS_TRI_LEV_1BYTE (0x0 << UART_FCR_RTS_TRI_LEV_Pos) /*!< UA_FCR setting to set RTS Trigger Level to 1 bit */ #define UART_FCR_RTS_TRI_LEV_4BYTES (0x1 << UART_FCR_RTS_TRI_LEV_Pos) /*!< UA_FCR setting to set RTS Trigger Level to 4 bits */ #define UART_FCR_RTS_TRI_LEV_8BYTES (0x2 << UART_FCR_RTS_TRI_LEV_Pos) /*!< UA_FCR setting to set RTS Trigger Level to 8 bits */ #define UART_FCR_RTS_TRI_LEV_14BYTES (0x3 << UART_FCR_RTS_TRI_LEV_Pos) /*!< UA_FCR setting to set RTS Trigger Level to 14 bits */ /*---------------------------------------------------------------------------------------------------------*/ /* UA_LCR constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_WORD_LEN_5 (0) /*!< UA_LCR setting to set UART word length to 5 bits */ #define UART_WORD_LEN_6 (1) /*!< UA_LCR setting to set UART word length to 6 bits */ #define UART_WORD_LEN_7 (2) /*!< UA_LCR setting to set UART word length to 7 bits */ #define UART_WORD_LEN_8 (3) /*!< UA_LCR setting to set UART word length to 8 bits */ #define UART_PARITY_NONE (0x0 << UART_LCR_PBE_Pos) /*!< UA_LCR setting to set UART as no parity */ #define UART_PARITY_ODD (0x1 << UART_LCR_PBE_Pos) /*!< UA_LCR setting to set UART as odd parity */ #define UART_PARITY_EVEN (0x3 << UART_LCR_PBE_Pos) /*!< UA_LCR setting to set UART as even parity */ #define UART_PARITY_MARK (0x5 << UART_LCR_PBE_Pos) /*!< UA_LCR setting to keep parity bit as '1' */ #define UART_PARITY_SPACE (0x7 << UART_LCR_PBE_Pos) /*!< UA_LCR setting to keep parity bit as '0' */ #define UART_STOP_BIT_1 (0x0 << UART_LCR_NSB_Pos) /*!< UA_LCR setting for one stop bit */ #define UART_STOP_BIT_1_5 (0x1 << UART_LCR_NSB_Pos) /*!< UA_LCR setting for 1.5 stop bit when 5-bit word length */ #define UART_STOP_BIT_2 (0x1 << UART_LCR_NSB_Pos) /*!< UA_LCR setting for two stop bit when 6, 7, 8-bit word length */ /*---------------------------------------------------------------------------------------------------------*/ /* UART RTS LEVEL TRIGGER constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_RTS_IS_HIGH_LEV_ACTIVE (0x1 << UART_MCR_LEV_RTS_Pos) /*!< Set RTS is High Level Active */ #define UART_RTS_IS_LOW_LEV_ACTIVE (0x0 << UART_MCR_LEV_RTS_Pos) /*!< Set RTS is Low Level Active */ /*---------------------------------------------------------------------------------------------------------*/ /* UA_IRCR constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_IRCR_TX_SELECT (1) /*!< Set IrDA function Tx mode */ #define UART_IRCR_RX_SELECT (0) /*!< Set IrDA function Rx mode */ /*---------------------------------------------------------------------------------------------------------*/ /* UA_FUNC_SEL constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_FUNC_SEL_UART (0x0 << UART_FUN_SEL_FUN_SEL_Pos) /*!< UA_FUNC_SEL setting to set UART Function (Default) */ #define UART_FUNC_SEL_LIN (0x1 << UART_FUN_SEL_FUN_SEL_Pos) /*!< UA_FUNC_SEL setting to set LIN Function */ #define UART_FUNC_SEL_IrDA (0x2 << UART_FUN_SEL_FUN_SEL_Pos) /*!< UA_FUNC_SEL setting to set IrDA Function */ #define UART_FUNC_SEL_RS485 (0x3 << UART_FUN_SEL_FUN_SEL_Pos) /*!< UA_FUNC_SEL setting to set RS485 Function */ /*@}*/ /* end of group M051_UART_EXPORTED_CONSTANTS */ /** @addtogroup M051_UART_EXPORTED_FUNCTIONS UART Exported Functions @{ */ /** * @brief Calculate UART baudrate mode0 divider * * @param None * * @return UART baudrate mode0 register setting value * */ #define UART_BAUD_MODE0 (0) /** * @brief Calculate UART baudrate mode0 divider * * @param None * * @return UART baudrate mode2 register setting value * */ #define UART_BAUD_MODE2 (UART_BAUD_DIV_X_EN_Msk | UART_BAUD_DIV_X_ONE_Msk) /** * @brief Calculate UART baudrate mode0 divider * * @param u32SrcFreq UART clock frequency * @param u32BaudRate Baudrate of UART module * * @return UART baudrate mode0 divider * */ #define UART_BAUD_MODE0_DIVIDER(u32SrcFreq, u32BaudRate) (((u32SrcFreq + (u32BaudRate*8)) / u32BaudRate >> 4)-2) /** * @brief Calculate UART baudrate mode2 divider * * @param u32SrcFreq UART clock frequency * @param u32BaudRate Baudrate of UART module * * @return UART baudrate mode2 divider */ #define UART_BAUD_MODE2_DIVIDER(u32SrcFreq, u32BaudRate) (((u32SrcFreq + (u32BaudRate/2)) / u32BaudRate)-2) /** * @brief Write Data to Tx data register * * @param uart The base address of UART module. * @param u8Data Data byte to transmit * * @return None */ #define UART_WRITE(uart, u8Data) (uart->THR = (u8Data)) /** * @brief Read Rx data register * * @param uart The base address of UART module. * * @return The oldest data byte in RX FIFO */ #define UART_READ(uart) (uart->RBR) /** * @brief Get Tx empty register value. * * @param uart The base address of UART module * * @return Tx empty register value. */ #define UART_GET_TX_EMPTY(uart) (uart->FSR & UART_FSR_TX_EMPTY_Msk) /** * @brief Get Rx empty register value. * * @param uart The base address of UART module * * @return Rx empty register value. */ #define UART_GET_RX_EMPTY(uart) (uart->FSR & UART_FSR_RX_EMPTY_Msk) /** * @brief Check specified uart port transmission is over. * * @param uart The base address of UART module * * @return TE_Flag. */ #define UART_IS_TX_EMPTY(uart) ((uart->FSR & UART_FSR_TE_FLAG_Msk) >> UART_FSR_TE_FLAG_Pos) /** * @brief Wait specified uart port transmission is over * * @param uart The base address of UART module * * @return None */ #define UART_WAIT_TX_EMPTY(uart) while(!(((uart->FSR) & UART_FSR_TE_FLAG_Msk) >> UART_FSR_TE_FLAG_Pos)) /** * @brief Check RDA_IF is set or not * * @param uart The base address of UART module * * @return * 0 : The number of bytes in the RX FIFO is less than the RFITL * 1 : The number of bytes in the RX FIFO equals or larger than RFITL */ #define UART_IS_RX_READY(uart) ((uart->ISR & UART_ISR_RDA_IF_Msk)>>UART_ISR_RDA_IF_Pos) /** * @brief Check TX FIFO is full or not * * @param uart The base address of UART module * * @return * 1 = TX FIFO is full * 0 = TX FIFO is not full */ #define UART_IS_TX_FULL(uart) ((uart->FSR & UART_FSR_TX_FULL_Msk)>>UART_FSR_TX_FULL_Pos) /** * @brief Check RX FIFO is full or not * * @param uart The base address of UART module * * @return * 1 = RX FIFO is full * 0 = RX FIFO is not full * */ #define UART_IS_RX_FULL(uart) ((uart->FSR & UART_FSR_RX_FULL_Msk)>>UART_FSR_RX_FULL_Pos) /** * @brief Get Tx full register value * * @param uart The base address of UART module * * @return Tx full register value */ #define UART_GET_TX_FULL(uart) (uart->FSR & UART_FSR_TX_FULL_Msk) /** * @brief Get Rx full register value * * @param uart The base address of UART module * * @return Rx full register value */ #define UART_GET_RX_FULL(uart) (uart->FSR & UART_FSR_RX_FULL_Msk) /** * @brief Enable specified interrupt * * @param uart The base address of UART module * @param u32eIntSel Interrupt type select * - UART_IER_LIN_RX_BRK_IEN_Msk : Lin bus Rx break field interrupt * - UART_IER_WAKE_EN_Msk : Wakeup interrupt * - UART_IER_BUF_ERR_IEN_Msk : Buffer Error interrupt * - UART_IER_RTO_IEN_Msk : Rx time-out interrupt * - UART_IER_MODEM_IEN_Msk : Modem interrupt * - UART_IER_RLS_IEN_Msk : Rx Line status interrupt * - UART_IER_THRE_IEN_Msk : Tx empty interrupt * - UART_IER_RDA_IEN_Msk : Rx ready interrupt * * @return None */ #define UART_ENABLE_INT(uart, u32eIntSel) (uart->IER |= (u32eIntSel)) /** * @brief Disable specified interrupt * * @param uart The base address of UART module * @param u32eIntSel Interrupt type select * - UART_IER_LIN_RX_BRK_IEN_Msk : Lin bus Rx break field interrupt * - UART_IER_WAKE_EN_Msk : Wakeup interrupt * - UART_IER_BUF_ERR_IEN_Msk : Buffer Error interrupt * - UART_IER_RTO_IEN_Msk : Rx time-out interrupt * - UART_IER_MODEM_IEN_Msk : Modem interrupt * - UART_IER_RLS_IEN_Msk : Rx Line status interrupt * - UART_IER_THRE_IEN_Msk : Tx empty interrupt * - UART_IER_RDA_IEN_Msk : Rx ready interrupt * @return None */ #define UART_DISABLE_INT(uart, u32eIntSel) (uart->IER &= ~ (u32eIntSel)) /** * @brief Get specified interrupt flag/status * * @param uart The base address of UART module * @param u32eIntTypeFlag Interrupt Type Flag,should be * - UART_ISR_LIN_RX_BREAK_INT_Msk : Lin bus interrupt * - UART_ISR_BUF_ERR_INT_Msk : Buffer Error interrupt * - UART_ISR_TOUT_INT_Msk : Rx time-out interrupt * - UART_ISR_MODEM_INT_Msk : Modem interrupt * - UART_ISR_RLS_INT_Msk : Rx Line status interrupt * - UART_ISR_THRE_INT_Msk : Tx empty interrupt * - UART_ISR_RDA_INT_Msk : Rx ready interrupt * * @return * 0 = The specified interrupt is not happened. * 1 = The specified interrupt is happened. */ #define UART_GET_INT_FLAG(uart,u32eIntTypeFlag) ((uart->ISR & (u32eIntTypeFlag))?1:0) /** * @brief Set RTS pin is low * * @param uart The base address of UART module * @return None */ __INLINE void UART_CLEAR_RTS(UART_T* uart) { uart->MCR |= UART_MCR_LEV_RTS_Msk; uart->MCR &= ~UART_MCR_RTS_Msk; } /** * @brief Set RTS pin is high * * @param uart The base address of UART module * @return None */ __INLINE void UART_SET_RTS(UART_T* uart) { uart->MCR |= UART_MCR_LEV_RTS_Msk | UART_MCR_RTS_Msk; } /** * @brief Clear RS-485 Address Byte Detection Flag * * @param uart The base address of UART module * @return None */ #define UART_RS485_CLEAR_ADDR_FLAG(uart) (uart->FSR |= UART_FSR_RS485_ADD_DETF_Msk) /** * @brief Get RS-485 Address Byte Detection Flag * * @param uart The base address of UART module * @return RS-485 Address Byte Detection Flag */ #define UART_RS485_GET_ADDR_FLAG(uart) ((uart->FSR & UART_FSR_RS485_ADD_DETF_Msk) >> UART_FSR_RS485_ADD_DETF_Pos) void UART_ClearIntFlag(UART_T* uart , uint32_t u32InterruptFlag); void UART_Close(UART_T* uart); void UART_DisableFlowCtrl(UART_T* uart); void UART_DisableInt(UART_T* uart, uint32_t u32InterruptFlag); void UART_EnableFlowCtrl(UART_T* uart); void UART_EnableInt(UART_T* uart, uint32_t u32InterruptFlag); void UART_Open(UART_T* uart, uint32_t u32baudrate); uint32_t UART_Read(UART_T* uart, uint8_t *pu8RxBuf, uint32_t u32ReadBytes); void UART_SetLine_Config(UART_T* uart, uint32_t u32baudrate, uint32_t u32data_width, uint32_t u32parity, uint32_t u32stop_bits); void UART_SetTimeoutCnt(UART_T* uart, uint32_t u32TOC); void UART_SelectIrDAMode(UART_T* uart, uint32_t u32Buadrate, uint32_t u32Direction); void UART_SelectRS485Mode(UART_T* uart, uint32_t u32Mode, uint32_t u32Addr); void UART_SelectLINMode(UART_T* uart, uint32_t u32Mode, uint32_t u32BreakLength); uint32_t UART_Write(UART_T* uart, uint8_t *pu8TxBuf, uint32_t u32WriteBytes); /*@}*/ /* end of group M051_UART_EXPORTED_FUNCTIONS */ /*@}*/ /* end of group M051_UART_Driver */ /*@}*/ /* end of group M051_Device_Driver */ #ifdef __cplusplus } #endif #endif //__UART_H__ /*** (C) COPYRIGHT 2013 Nuvoton Technology Corp. ***/