Linux tunnels were written before RFC6040 and therefore never
implemented the corner case of ECN getting set in the outer header
and the inner header not being ready for it.

Section 4.2.  Default Tunnel Egress Behaviour.
 o If the inner ECN field is Not-ECT, the decapsulator MUST NOT
      propagate any other ECN codepoint onwards.  This is because the
      inner Not-ECT marking is set by transports that rely on dropped
      packets as an indication of congestion and would not understand or
      respond to any other ECN codepoint [RFC4774].  Specifically:

      *  If the inner ECN field is Not-ECT and the outer ECN field is
         CE, the decapsulator MUST drop the packet.

      *  If the inner ECN field is Not-ECT and the outer ECN field is
         Not-ECT, ECT(0), or ECT(1), the decapsulator MUST forward the
         outgoing packet with the ECN field cleared to Not-ECT.

This patch moves the ECN decap logic out of the individual tunnels
into a common place.

It also adds logging to allow detecting broken systems that
set ECN bits incorrectly when tunneling (or an intermediate
router might be changing the header).

Overloads rx_frame_error to keep track of ECN related error.

Thanks to Chris Wright who caught this while reviewing the new VXLAN
tunnel.

This code was tested by injecting faulty logic in other end GRE
to send incorrectly encapsulated packets.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The handlers for xfrm_tunnel are always invoked with rcu read lock
already.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The gre function pointers for receive and error handling are
always called (from gre.c) with rcu_read_lock already held.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GRE driver incorrectly uses zero as a flag value. Zero is a perfectly
valid value for key, and the tunnel should match packets with no key only
with tunnels created without key, and vice versa.

This is a slightly visible  change since previously it might be possible to
construct a working tunnel that sent key 0 and received only because
of the key wildcard of zero.  I.e the sender sent key of zero, but tunnel
was defined without key.

Note: using gre key 0 requires iproute2 utilities v3.2 or later.
The original utility code was broken as well.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is a follow-up for patch "filter: add XOR instruction for use
with X/K" that implements BPF SPARC JIT parts for the BPF XOR operation.
Signed-off-by: NDaniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds proper handling of the buggy revision A2 of LXT973 phy, adding
precautions linked to ERRATA Item 4:

Revision A2 of LXT973 chip randomly returns the contents of the previous even
register when you read a odd register regularly
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new common code routine to upgrade an adapter's
firmware.  This routine handles all of the complexities of working with the
the existing adapter firmware in order to quiesce the adapter and uP, etc.
For an automatic upgrade it will send a HELLO command to check if cxgb4
want/can upgrade firmware, i.e. if cxgb4 is MASTER and has newer firmware
that it wants to load and call the new common code routine t4_fw_upgrade.
Note that it should not issue a RESET command after a successful firmware
upgrade.
Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a card had already been initialized, on reloading cxgb4 driver firmware
required an upgrade but the upgrade did not happen. In that case a mailbox
timeout would occur during T4 configuration file stuff. The fix is to let the
caller know the firmware was not upgraded so a reset would be issued before
starting the T4 config stuff.
Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case if user defined configuration file at /lib/firmware/cxgb4/t4-config.txt
location and also factory default configuration file written to FLASH are not
present then driver will use hardwired configuration settings.
Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Starting with T4 firmware version 1.3.11.0 the firmware now supports device
configuration via a Firmware Configuration File. The Firmware Configuration
File was primarily developed in order to centralize all of the configuration,
resource allocation, etc. for Unified Wire operation where multiple
Physical / Virtual Function Drivers would be using a T4 adapter simultaneously.

The Firmware Configuration file can live in three locations as shown below
in order of precedence.
1) User defined configuration file: /lib/firmware/cxgb4/t4-config.txt
2) Factory Default configuration file written to FLASH within
   the manufacturing process.
3) Hardwired driver configuration.
Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds new enums and macros to enable T4 configuration file support. It
also removes duplicate macro definitions.

It fixes the build failure in cxgb4vf driver introduced because of old macro
definition removal.

It also performs SGE initialization based on T4 configuration file is provided
or not. If it is provided then it uses the parameters provided in it otherwise
it uses hard coded values.
Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements two new functions t4_mem_win_read and t4_memory_read.
These new functions can be used to read memory via the PCIE memory window.
Please note, for proper execution of these functions PCIE_MEM_ACCESS_BASE_WIN
registers must be setup correctly like how setup_memwin in the cxgb4 driver
does it.
Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 5e953778 ("ipconfig: add nameserver
IPs to kernel-parameter ip=") introduces ic_nameservers_predef() that defined
only for BOOTP. However it is used by ip_auto_config_setup() as well. This
patch moves it outside of #ifdef BOOTP.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Christoph Fritz <chf.fritz@googlemail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 5640f768 ("net: use a per task frag allocator")
accidentally contained an unrelated change to net/ipv4/raw.c,
later committed (without the pr_err() debugging bits) in
net tree as commit ab43ed8b (ipv4: raw: fix icmp_filter())

This patch reverts this glitch, noticed by Stephen Rothwell.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is a follow-up for patch "filter: add XOR instruction for use
with X/K" that implements BPF x86 JIT parts for the BPF XOR operation.
Signed-off-by: NDaniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SKF_AD_ALU_XOR_X has been added a while ago, but as an 'ancillary'
operation that is invoked through a negative offset in K within BPF
load operations. Since BPF_MOD has recently been added, BPF_XOR should
also be part of the common ALU operations. Removing SKF_AD_ALU_XOR_X
might not be an option since this is exposed to user space.
Signed-off-by: NDaniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MIPSsim platform is no longer supported or used. This patch
deletes the Ethernet driver.
Signed-off-by: NSteven J. Hill <sjhill@mips.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We currently use a per socket order-0 page cache for tcp_sendmsg()
operations.

This page is used to build fragments for skbs.

Its done to increase probability of coalescing small write() into
single segments in skbs still in write queue (not yet sent)

But it wastes a lot of memory for applications handling many mostly
idle sockets, since each socket holds one page in sk->sk_sndmsg_page

Its also quite inefficient to build TSO 64KB packets, because we need
about 16 pages per skb on arches where PAGE_SIZE = 4096, so we hit
page allocator more than wanted.

This patch adds a per task frag allocator and uses bigger pages,
if available. An automatic fallback is done in case of memory pressure.

(up to 32768 bytes per frag, thats order-3 pages on x86)

This increases TCP stream performance by 20% on loopback device,
but also benefits on other network devices, since 8x less frags are
mapped on transmit and unmapped on tx completion. Alexander Duyck
mentioned a probable performance win on systems with IOMMU enabled.

Its possible some SG enabled hardware cant cope with bigger fragments,
but their ndo_start_xmit() should already handle this, splitting a
fragment in sub fragments, since some arches have PAGE_SIZE=65536

Successfully tested on various ethernet devices.
(ixgbe, igb, bnx2x, tg3, mellanox mlx4)
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Vijay Subramanian <subramanian.vijay@gmail.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NVijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is primarily to address transmission timeout occurrences, when
multiple H/W Tx queues are being used concurrently. Because in
the priority scheduling mode the controller does not service the
Tx queues equally (but in ascending index order), Tx timeouts are
being triggered rightaway for a basic test with multiple simultaneous
connections like:
iperf -c <server_ip> -n 100M -P 8

resulting in kernel trace:
NETDEV WATCHDOG: eth1 (fsl-gianfar): transmit queue <X> timed out
------------[ cut here ]------------
WARNING: at net/sched/sch_generic.c:255
...
and controller reset during intense traffic, and possibly further
complications.

This patch changes the default H/W Tx scheduling setting (TXSCHED)
for multi-queue devices, from priority scheduling mode to a weighted
round robin mode with equal weights for all H/W Tx queues, and
addresses the issue above.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

loopback current mtu of 16436 bytes allows no more than 3 MSS TCP
segments per frame, or 48 Kbytes. Changing mtu to 64K allows TCP
stack to build large frames and significantly reduces stack overhead.

Performance boost on bulk TCP transferts can be up to 30 %, partly
because we now have one ACK message for two 64KB segments, and a lower
probability of hitting /proc/sys/net/ipv4/tcp_reordering default limit.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All callers provide a non-NULL scm argument.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the definition of bnx2x_tests_str_arr from static char
pointer to static const char bi-directional array. Also the
bnx2x_get_strings function is simplified.
Reported-by: NJoe Perches <joe@perches.com>
Reported-by: NDavid Laight <David.Laight@ACULAB.COM>
Signed-off-by: NMerav Sicron <meravs@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

removes unnecessary semicolon

Found by Coccinelle: http://coccinelle.lip6.fr/Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ipaddr has been allocated in function qeth_l3_add_vipa() but
does not free before leaving from the error handling cases. The
same problem also exists in function qeth_l3_add_rxip().

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure that all ccws used for writing are initialized with
zeros - especially since the last ccw contains a TIC for which
the unused fields have to be zeros.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleanup the qeth_get_channel_path_desc function and rename it
to qeth_update_from_chp_desc. No functional change.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Acked-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
This patchset contains updates for your net-next tree, they are:

* Mostly fixes for the recently pushed IPv6 NAT support:

- Fix crash while removing nf_nat modules from Patrick McHardy.
- Fix unbalanced rcu_read_unlock from Ulrich Weber.
- Merge NETMAP and REDIRECT into one single xt_target module, from
  Jan Engelhardt.
- Fix Kconfig for IPv6 NAT, which allows inconsistent configurations,
  from myself.

* Updates for ipset, all of the from Jozsef Kadlecsik:

- Add the new "nomatch" option to obtain reverse set matching.
- Support for /0 CIDR in hash:net,iface set type.
- One non-critical fix for a rare crash due to pass really
  wrong configuration parameters.
- Coding style cleanups.
- Sparse fixes.
- Add set revision supported via modinfo.i

* One extension for the xt_time match, to support matching during
  the transition between two days with one single rule, from
  Florian Westphal.

* Fix maximum packet length supported by nfnetlink_queue and add
  NFQA_CAP_LEN attribute, from myself.

You can notice that this batch contains a couple of fixes that may
go to 3.6-rc but I don't consider them critical to push them:

* The ipset fix for the /0 cidr case, which is triggered with one
  inconsistent command line invocation of ipset.

* The nfnetlink_queue maximum packet length supported since it requires
  the new NFQA_CAP_LEN attribute to provide a full workaround for the
  described problem.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the NFQA_CAP_LEN attribute that allows us to know
what is the real packet size from user-space (even if we decided
to retrieve just a few bytes from the packet instead of all of it).

Security software that inspects packets should always check for
this new attribute to make sure that it is inspecting the entire
packet.

This also helps to provide a workaround for the problem described
in: http://marc.info/?l=netfilter-devel&m=134519473212536&w=2

Original idea from Florian Westphal.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

The packets that we send via NFQUEUE are encapsulated in the NFQA_PAYLOAD
attribute. The length of the packet in userspace is obtained via
attr->nla_len field. This field contains the size of the Netlink
attribute header plus the packet length.

If the maximum packet length is specified, ie. 65535 bytes, and
packets in the range of (65531,65535] are sent to userspace, the
attr->nla_len overflows and it reports bogus lengths to the
application.

To fix this, this patch limits the maximum packet length to 65531
bytes. If larger packet length is specified, the packet that we
send to user-space is truncated to 65531 bytes.

To support 65535 bytes packets, we have to revisit the idea of
the 32-bits Netlink attribute length.
Reported-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

This patch allows the FTP helper to pickup the sequence tracking from
the first packet seen. This is useful to fix the breakage of the first
FTP command after the failover while using conntrackd to synchronize
states.

The seq_aft_nl_num field in struct nf_ct_ftp_info has been shrinked to
16-bits (enough for what it does), so we can use the remaining 16-bits
to store the flags while using the same size for the private FTP helper
data.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Currently, if you want to do something like:
"match Monday, starting 23:00, for two hours"
You need two rules, one for Mon 23:00 to 0:00 and one for Tue 0:00-1:00.

The rule: --weekdays Mo --timestart 23:00  --timestop 01:00

looks correct, but it will first match on monday from midnight to 1 a.m.
and then again for another hour from 23:00 onwards.

This permits userspace to explicitly ignore the day transition and
match for a single, continuous time period instead.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

With recent kernel changes we can now return errors on a failure to setup a
VLAN filter.  This patch takes advantage of that opportunity so that we can
return either an EIO error in the case of a mailbox failure, or an EACCESS
error in the case of being denied access to the VLAN filter table by the
PF.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRobert Garrett <robertx.e.garrett@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change fixes the ixgbevf driver so that it can correctly drop a frame
should it receive a jumbo frame.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

While fixing up a patch from Alex Duyck to use q_vectors in ring containers
to update the ITR I bungled it and missed actually updating the counters
in the ring container q_vectors.  This patch fixes my mistake and makes
interrupt moderation actually work.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove 'rx_ring' parameter as it is not used in ixgbevf_receive_skb
Signed-off-by: NNarendra K <narendra_k@dell.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The counter is not valid unless the controller is running in IOV mode.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VF driver was not designed to correctly handle a message timeout.  As
a result it is possible for one bad message to invalidate all messages
following it until the part is reset.  Instead we should copy the example
in igbvf of how to handle a mailbox event and message timeout.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Suggested by Jan Engelhardt.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>