1. 15 4月, 2016 10 次提交
    • C
      soreuseport: fix ordering for mixed v4/v6 sockets · d894ba18
      Craig Gallek 提交于
      With the SO_REUSEPORT socket option, it is possible to create sockets
      in the AF_INET and AF_INET6 domains which are bound to the same IPv4 address.
      This is only possible with SO_REUSEPORT and when not using IPV6_V6ONLY on
      the AF_INET6 sockets.
      
      Prior to the commits referenced below, an incoming IPv4 packet would
      always be routed to a socket of type AF_INET when this mixed-mode was used.
      After those changes, the same packet would be routed to the most recently
      bound socket (if this happened to be an AF_INET6 socket, it would
      have an IPv4 mapped IPv6 address).
      
      The change in behavior occurred because the recent SO_REUSEPORT optimizations
      short-circuit the socket scoring logic as soon as they find a match.  They
      did not take into account the scoring logic that favors AF_INET sockets
      over AF_INET6 sockets in the event of a tie.
      
      To fix this problem, this patch changes the insertion order of AF_INET
      and AF_INET6 addresses in the TCP and UDP socket lists when the sockets
      have SO_REUSEPORT set.  AF_INET sockets will be inserted at the head of the
      list and AF_INET6 sockets with SO_REUSEPORT set will always be inserted at
      the tail of the list.  This will force AF_INET sockets to always be
      considered first.
      
      Fixes: e32ea7e7 ("soreuseport: fast reuseport UDP socket selection")
      Fixes: 125e80b88687 ("soreuseport: fast reuseport TCP socket selection")
      Reported-by: NMaciej Żenczykowski <maze@google.com>
      Signed-off-by: NCraig Gallek <kraig@google.com>
      Signed-off-by: NEric Dumazet <edumazet@google.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d894ba18
    • B
      cdc_mbim: apply "NDP to end" quirk to all Huawei devices · c5b5343c
      Bjørn Mork 提交于
      We now have a positive report of another Huawei device needing
      this quirk: The ME906s-158 (12d1:15c1).  This is an m.2 form
      factor modem with no obvious relationship to the E3372 (12d1:157d)
      we already have a quirk entry for.  This is reason enough to
      believe the quirk might be necessary for any number of current
      and future Huawei devices.
      
      Applying the quirk to all Huawei devices, since it is crucial
      to any device affected by the firmware bug, while the impact
      on non-affected devices is negligible.
      
      The quirk can if necessary be disabled per-device by writing
      N to /sys/class/net/<iface>/cdc_ncm/ndp_to_end
      Reported-by: NAndreas Fett <andreas.fett@secunet.com>
      Signed-off-by: NBjørn Mork <bjorn@mork.no>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c5b5343c
    • R
      bgmac: reset & enable Ethernet core before using it · b4dfd8e9
      Rafał Miłecki 提交于
      This fixes Ethernet on D-Link DIR-885L with BCM47094 SoC. Felix reported
      similar fix was needed for his BCM4709 device (Buffalo WXR-1900DHP?).
      I tested this for regressions on BCM4706, BCM4708A0 and BCM47081A0.
      
      Cc: Felix Fietkau <nbd@openwrt.org>
      Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b4dfd8e9
    • D
      Merge branch 'ipv6-dgram-dst-cache' · 97cc931f
      David S. Miller 提交于
      Martin KaFai Lau says:
      
      ====================
      ipv6: datagram: Update dst cache of a connected udp sk during pmtu update
      
      v2:
      ~ Protect __sk_dst_get() operations with rcu_read_lock in
        release_cb() because another thread may do ip6_dst_store()
        for a udp sk without taking the sk lock (e.g. in sendmsg).
      ~ Do a ipv6_addr_v4mapped(&sk->sk_v6_daddr) check before
        calling ip6_datagram_dst_update() in patch 3 and 4.  It is
        similar to how __ip6_datagram_connect handles it.
      ~ One fix in ip6_datagram_dst_update() in patch 2.  It needs
        to check (np->flow_label & IPV6_FLOWLABEL_MASK) before
        doing fl6_sock_lookup.  I was confused with the naming
        of IPV6_FLOWLABEL_MASK and IPV6_FLOWINFO_MASK.
      ~ Check dst->obsolete just on the safe side, although I think it
        should at least have DST_OBSOLETE_FORCE_CHK by now.
      ~ Add Fixes tag to patch 3 and 4
      ~ Add some points from the previous discussion about holding
        sk lock to the commit message in patch 3.
      
      v1:
      There is a case in connected UDP socket such that
      getsockopt(IPV6_MTU) will return a stale MTU value. The reproducible
      sequence could be the following:
      1. Create a connected UDP socket
      2. Send some datagrams out
      3. Receive a ICMPV6_PKT_TOOBIG
      4. No new outgoing datagrams to trigger the sk_dst_check()
         logic to update the sk->sk_dst_cache.
      5. getsockopt(IPV6_MTU) returns the mtu from the invalid
         sk->sk_dst_cache instead of the newly created RTF_CACHE clone.
      
      Patch 1 and 2 are the prep work.
      Patch 3 and 4 are the fixes.
      ====================
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      97cc931f
    • M
      ipv6: udp: Do a route lookup and update during release_cb · e646b657
      Martin KaFai Lau 提交于
      This patch adds a release_cb for UDPv6.  It does a route lookup
      and updates sk->sk_dst_cache if it is needed.  It picks up the
      left-over job from ip6_sk_update_pmtu() if the sk was owned
      by user during the pmtu update.
      
      It takes a rcu_read_lock to protect the __sk_dst_get() operations
      because another thread may do ip6_dst_store() without taking the
      sk lock (e.g. sendmsg).
      
      Fixes: 45e4fd26 ("ipv6: Only create RTF_CACHE routes after encountering pmtu exception")
      Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
      Reported-by: NWei Wang <weiwan@google.com>
      Cc: Cong Wang <xiyou.wangcong@gmail.com>
      Cc: Eric Dumazet <edumazet@google.com>
      Cc: Wei Wang <weiwan@google.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      e646b657
    • M
      ipv6: datagram: Update dst cache of a connected datagram sk during pmtu update · 33c162a9
      Martin KaFai Lau 提交于
      There is a case in connected UDP socket such that
      getsockopt(IPV6_MTU) will return a stale MTU value. The reproducible
      sequence could be the following:
      1. Create a connected UDP socket
      2. Send some datagrams out
      3. Receive a ICMPV6_PKT_TOOBIG
      4. No new outgoing datagrams to trigger the sk_dst_check()
         logic to update the sk->sk_dst_cache.
      5. getsockopt(IPV6_MTU) returns the mtu from the invalid
         sk->sk_dst_cache instead of the newly created RTF_CACHE clone.
      
      This patch updates the sk->sk_dst_cache for a connected datagram sk
      during pmtu-update code path.
      
      Note that the sk->sk_v6_daddr is used to do the route lookup
      instead of skb->data (i.e. iph).  It is because a UDP socket can become
      connected after sending out some datagrams in un-connected state.  or
      It can be connected multiple times to different destinations.  Hence,
      iph may not be related to where sk is currently connected to.
      
      It is done under '!sock_owned_by_user(sk)' condition because
      the user may make another ip6_datagram_connect()  (i.e changing
      the sk->sk_v6_daddr) while dst lookup is happening in the pmtu-update
      code path.
      
      For the sock_owned_by_user(sk) == true case, the next patch will
      introduce a release_cb() which will update the sk->sk_dst_cache.
      
      Test:
      
      Server (Connected UDP Socket):
      ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
      Route Details:
      [root@arch-fb-vm1 ~]# ip -6 r show | egrep '2fac'
      2fac::/64 dev eth0  proto kernel  metric 256  pref medium
      2fac:face::/64 via 2fac::face dev eth0  metric 1024  pref medium
      
      A simple python code to create a connected UDP socket:
      
      import socket
      import errno
      
      HOST = '2fac::1'
      PORT = 8080
      
      s = socket.socket(socket.AF_INET6, socket.SOCK_DGRAM)
      s.bind((HOST, PORT))
      s.connect(('2fac:face::face', 53))
      print("connected")
      while True:
          try:
      	data = s.recv(1024)
          except socket.error as se:
      	if se.errno == errno.EMSGSIZE:
      		pmtu = s.getsockopt(41, 24)
      		print("PMTU:%d" % pmtu)
      		break
      s.close()
      
      Python program output after getting a ICMPV6_PKT_TOOBIG:
      [root@arch-fb-vm1 ~]# python2 ~/devshare/kernel/tasks/fib6/udp-connect-53-8080.py
      connected
      PMTU:1300
      
      Cache routes after recieving TOOBIG:
      [root@arch-fb-vm1 ~]# ip -6 r show table cache
      2fac:face::face via 2fac::face dev eth0  metric 0
          cache  expires 463sec mtu 1300 pref medium
      
      Client (Send the ICMPV6_PKT_TOOBIG):
      ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
      scapy is used to generate the TOOBIG message.  Here is the scapy script I have
      used:
      
      >>> p=Ether(src='da:75:4d:36:ac:32', dst='52:54:00:12:34:66', type=0x86dd)/IPv6(src='2fac::face', dst='2fac::1')/ICMPv6PacketTooBig(mtu=1300)/IPv6(src='2fac::
      1',dst='2fac:face::face', nh='UDP')/UDP(sport=8080,dport=53)
      >>> sendp(p, iface='qemubr0')
      
      Fixes: 45e4fd26 ("ipv6: Only create RTF_CACHE routes after encountering pmtu exception")
      Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
      Reported-by: NWei Wang <weiwan@google.com>
      Cc: Cong Wang <xiyou.wangcong@gmail.com>
      Cc: Eric Dumazet <edumazet@google.com>
      Cc: Wei Wang <weiwan@google.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      33c162a9
    • M
      ipv6: datagram: Refactor dst lookup and update codes to a new function · 7e2040db
      Martin KaFai Lau 提交于
      This patch moves the route lookup and update codes for connected
      datagram sk to a newly created function ip6_datagram_dst_update()
      
      It will be reused during the pmtu update in the later patch.
      Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
      Cc: Cong Wang <xiyou.wangcong@gmail.com>
      Cc: Eric Dumazet <edumazet@google.com>
      Cc: Wei Wang <weiwan@google.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7e2040db
    • M
      ipv6: datagram: Refactor flowi6 init codes to a new function · 80fbdb20
      Martin KaFai Lau 提交于
      Move flowi6 init codes for connected datagram sk to a newly created
      function ip6_datagram_flow_key_init().
      
      Notes:
      1. fl6_flowlabel is used instead of fl6.flowlabel in __ip6_datagram_connect
      2. ipv6_addr_is_multicast(&fl6->daddr) is used instead of
         (addr_type & IPV6_ADDR_MULTICAST) in ip6_datagram_flow_key_init()
      
      This new function will be reused during pmtu update in the later patch.
      Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
      Cc: Cong Wang <xiyou.wangcong@gmail.com>
      Cc: Eric Dumazet <edumazet@google.com>
      Cc: Wei Wang <weiwan@google.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      80fbdb20
    • J
      net: mediatek: update the IRQ part of the binding document · f1d0540d
      John Crispin 提交于
      The current binding document only describes a single interrupt. Update the
      document by adding the 2 other interrupts.
      
      The driver currently only uses a single interrupt. The HW is however able
      to using IRQ grouping to split TX and RX onto separate GIC irqs.
      Signed-off-by: NJohn Crispin <blogic@openwrt.org>
      Cc: devicetree@vger.kernel.org
      Acked-by: NRob Herring <robh@kernel.org>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f1d0540d
    • D
      Merge tag 'mac80211-for-davem-2016-04-14' of... · 5e265029
      David S. Miller 提交于
      Merge tag 'mac80211-for-davem-2016-04-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
      
      Johannes Berg says:
      
      ====================
      This has just the single fix from Dmitry Ivanov, adding the missing
      netlink notifier family check to avoid the socket close DoS problem.
      ====================
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5e265029
  2. 14 4月, 2016 13 次提交
    • A
      bpf/verifier: reject invalid LD_ABS | BPF_DW instruction · d82bccc6
      Alexei Starovoitov 提交于
      verifier must check for reserved size bits in instruction opcode and
      reject BPF_LD | BPF_ABS | BPF_DW and BPF_LD | BPF_IND | BPF_DW instructions,
      otherwise interpreter will WARN_RATELIMIT on them during execution.
      
      Fixes: ddd872bc ("bpf: verifier: add checks for BPF_ABS | BPF_IND instructions")
      Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
      Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d82bccc6
    • L
      net: sched: do not requeue a NULL skb · 3dcd493f
      Lars Persson 提交于
      A failure in validate_xmit_skb_list() triggered an unconditional call
      to dev_requeue_skb with skb=NULL. This slowly grows the queue
      discipline's qlen count until all traffic through the queue stops.
      
      We take the optimistic approach and continue running the queue after a
      failure since it is unknown if later packets also will fail in the
      validate path.
      
      Fixes: 55a93b3e ("qdisc: validate skb without holding lock")
      Signed-off-by: NLars Persson <larper@axis.com>
      Acked-by: NEric Dumazet <edumazet@google.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      3dcd493f
    • M
      packet: fix heap info leak in PACKET_DIAG_MCLIST sock_diag interface · 309cf37f
      Mathias Krause 提交于
      Because we miss to wipe the remainder of i->addr[] in packet_mc_add(),
      pdiag_put_mclist() leaks uninitialized heap bytes via the
      PACKET_DIAG_MCLIST netlink attribute.
      
      Fix this by explicitly memset(0)ing the remaining bytes in i->addr[].
      
      Fixes: eea68e2f ("packet: Report socket mclist info via diag module")
      Signed-off-by: NMathias Krause <minipli@googlemail.com>
      Cc: Eric W. Biederman <ebiederm@xmission.com>
      Cc: Pavel Emelyanov <xemul@parallels.com>
      Acked-by: NPavel Emelyanov <xemul@virtuozzo.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      309cf37f
    • D
      Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue · 41015e89
      David S. Miller 提交于
      Jeff Kirsher says:
      
      ====================
      Intel Wired LAN Driver Updates 2016-04-13
      
      This series contains updates to i40e, i40evf and fm10k.
      
      Alex fixes a bug introduced earlier based on his interpretation of the
      XL710 datasheet.  The actual limit for fragments with TSO and a skbuff
      that has payload data in the header portion of the buffer is actually
      only 7 fragments and the skb-data portion counts as 2 buffers, one for
      the TSO header, and the one for a segment payload buffer.
      
      Jacob fixes a bug where in a previous refactor of the code broke
      multi-bit updates for VFs.  The problem occurs because a multi-bit
      request has a non-zero length, and the PF would simply drop any
      request with the upper 16 bits set.
      ====================
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      41015e89
    • C
      route: do not cache fib route info on local routes with oif · d6d5e999
      Chris Friesen 提交于
      For local routes that require a particular output interface we do not want
      to cache the result.  Caching the result causes incorrect behaviour when
      there are multiple source addresses on the interface.  The end result
      being that if the intended recipient is waiting on that interface for the
      packet he won't receive it because it will be delivered on the loopback
      interface and the IP_PKTINFO ipi_ifindex will be set to the loopback
      interface as well.
      
      This can be tested by running a program such as "dhcp_release" which
      attempts to inject a packet on a particular interface so that it is
      received by another program on the same board.  The receiving process
      should see an IP_PKTINFO ipi_ifndex value of the source interface
      (e.g., eth1) instead of the loopback interface (e.g., lo).  The packet
      will still appear on the loopback interface in tcpdump but the important
      aspect is that the CMSG info is correct.
      
      Sample dhcp_release command line:
      
         dhcp_release eth1 192.168.204.222 02:11:33:22:44:66
      Signed-off-by: NAllain Legacy <allain.legacy@windriver.com>
      Signed off-by: Chris Friesen <chris.friesen@windriver.com>
      Reviewed-by: NJulian Anastasov <ja@ssi.bg>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d6d5e999
    • J
      fm10k: fix multi-bit VLAN update requests from VF · f808c5db
      Jacob Keller 提交于
      The VF uses a multi-bit update request to clear unused VLANs whenever it
      resets. However, an accident in a previous refector broke multi-bit
      updates for VFs, due to misreading a comment in fm10k_vf.c and
      attempting to reduce code duplication. The problem occurs because
      a multi-bit request has a non-zero length, and the PF would simply drop
      any request with the upper 16 bits set.
      
      We can't simply remove the check of the upper 16 bits and the call to
      fm10k_iov_select vid, because this would remove the checks for default
      VID and for ensuring no other VLANs can be enabled except pf_vid when it
      has been set. To resolve that issue, this revision uses the
      iov_select_vid when we have a single-bit update, and denies any
      multi-bit update when the VLAN was administratively set by the PF. This
      should be ok since the PF properly updates VLAN_TABLE when it assigns
      the PF vid. This ensures that requests to add or remove the PF vid work
      as expected, but a rogue VF could not use the multi-bit update as
      a loophole to attempt receiving traffic on other VLANs.
      Reported-by: NNgai-Mint Kwan <ngai-mint.kwan@intel.com>
      Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
      Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
      Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
      f808c5db
    • D
      net: thunderx: Fix broken of_node_put() code. · 65c66af6
      David Daney 提交于
      commit b7d3e3d3 ("net: thunderx: Don't leak phy device references
      on -EPROBE_DEFER condition.") incorrectly moved the call to
      of_node_put() outside of the loop.  Under normal loop exit, the node
      has already had of_node_put() called, so the extra call results in:
      
      [    8.228020] ERROR: Bad of_node_put() on /soc@0/pci@848000000000/mrml-bridge0@1,0/bgx0/xlaui00
      [    8.239433] CPU: 16 PID: 608 Comm: systemd-udevd Not tainted 4.6.0-rc1-numa+ #157
      [    8.247380] Hardware name: www.cavium.com EBB8800/EBB8800, BIOS 0.3 Mar  2 2016
      [    8.273541] Call trace:
      [    8.273550] [<fffffc0008097364>] dump_backtrace+0x0/0x210
      [    8.273557] [<fffffc0008097598>] show_stack+0x24/0x2c
      [    8.273560] [<fffffc0008399ed0>] dump_stack+0x8c/0xb4
      [    8.273566] [<fffffc00085aa828>] of_node_release+0xa8/0xac
      [    8.273570] [<fffffc000839cad8>] kobject_cleanup+0x8c/0x194
      [    8.273573] [<fffffc000839c97c>] kobject_put+0x44/0x6c
      [    8.273576] [<fffffc00085a9ab0>] of_node_put+0x24/0x30
      [    8.273587] [<fffffc0000bd0f74>] bgx_probe+0x17c/0xcd8 [thunder_bgx]
      [    8.273591] [<fffffc00083ed220>] pci_device_probe+0xa0/0x114
      [    8.273596] [<fffffc0008473fbc>] driver_probe_device+0x178/0x418
      [    8.273599] [<fffffc000847435c>] __driver_attach+0x100/0x118
      [    8.273602] [<fffffc0008471b58>] bus_for_each_dev+0x6c/0xac
      [    8.273605] [<fffffc0008473884>] driver_attach+0x30/0x38
      [    8.273608] [<fffffc00084732f4>] bus_add_driver+0x1f8/0x29c
      [    8.273611] [<fffffc0008475028>] driver_register+0x70/0x110
      [    8.273617] [<fffffc00083ebf08>] __pci_register_driver+0x60/0x6c
      [    8.273623] [<fffffc0000bf0040>] bgx_init_module+0x40/0x48 [thunder_bgx]
      [    8.273626] [<fffffc0008090d04>] do_one_initcall+0xcc/0x1c0
      [    8.273631] [<fffffc0008198abc>] do_init_module+0x68/0x1c8
      [    8.273635] [<fffffc0008125668>] load_module+0xf44/0x11f4
      [    8.273638] [<fffffc0008125b64>] SyS_finit_module+0xb8/0xe0
      [    8.273641] [<fffffc0008093b30>] el0_svc_naked+0x24/0x28
      
      Go back to the previous (correct) code that only did the extra
      of_node_put() call on early exit from the loop.
      Signed-off-by: NDavid Daney <david.daney@cavium.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      65c66af6
    • E
      mISDN: Fixing missing validation in base_sock_bind() · b8216468
      Emrah Demir 提交于
      Add validation code into mISDN/socket.c
      Signed-off-by: NEmrah Demir <ed@abdsec.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      b8216468
    • A
      i40e/i40evf: Limit TSO to 7 descriptors for payload instead of 8 per packet · 3f3f7cb8
      Alexander Duyck 提交于
      This patch addresses a bug introduced based on my interpretation of the
      XL710 datasheet.  Specifically section 8.4.1 states that "A single transmit
      packet may span up to 8 buffers (up to 8 data descriptors per packet
      including both the header and payload buffers)."  It then later goes on to
      say that each segment for a TSO obeys the previous rule, however it then
      refers to TSO header and the segment payload buffers.
      
      I believe the actual limit for fragments with TSO and a skbuff that has
      payload data in the header portion of the buffer is actually only 7
      fragments as the skb->data portion counts as 2 buffers, one for the TSO
      header, and one for a segment payload buffer.
      
      Fixes: 2d37490b ("i40e/i40evf: Rewrite logic for 8 descriptor per packet check")
      Reported-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
      Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
      Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
      Tested-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
      Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
      3f3f7cb8
    • D
      net: ipv6: Do not keep linklocal and loopback addresses · 70af921d
      David Ahern 提交于
      f1705ec1 added the option to retain user configured addresses on an
      admin down. A comment to one of the later revisions suggested using the
      IFA_F_PERMANENT flag rather than adding a user_managed boolean to the
      ifaddr struct. A side effect of this change is that link local and
      loopback addresses are also retained which is not part of the objective
      of f1705ec1. Add check to drop those addresses.
      
      Fixes: f1705ec1 ("net: ipv6: Make address flushing on ifdown optional")
      Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      70af921d
    • W
      net: ethernet: renesas: ravb_main: test clock rate to avoid division by 0 · a6d37131
      Wolfram Sang 提交于
      The clk API may return 0 on clk_get_rate, so we should check the result before
      using it as a divisor.
      Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
      Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a6d37131
    • D
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf · 60e19518
      David S. Miller 提交于
      Pablo Neira Ayuso says:
      
      ====================
      Netfilter fixes for net
      
      The following patchset contains Netfilter fixes for your net tree. More
      specifically, they are:
      
      1) Fix missing filter table per-netns registration in arptables, from
         Florian Westphal.
      
      2) Resolve out of bound access when parsing TCP options in
         nf_conntrack_tcp, patch from Jozsef Kadlecsik.
      
      3) Prefer NFPROTO_BRIDGE extensions over NFPROTO_UNSPEC in ebtables,
         this resolves conflict between xt_limit and ebt_limit, from Phil Sutter.
      ====================
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      60e19518
    • D
      Merge tag 'wireless-drivers-for-davem-2016-04-13' of... · 4bc0eb3a
      David S. Miller 提交于
      Merge tag 'wireless-drivers-for-davem-2016-04-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
      
      Kalle Valo says:
      
      ====================
      wireless-drivers fixes for 4.6
      
      b43
      
      * fix memory leaks when removing the device
      
      bcma
      
      * fix building without OF_IRQ
      
      rtlwifi
      
      * fix gcc-6 indentation warning
      
      iwlwifi
      
      * lower the debug level of a benign print
      * fix a memory leak
      ====================
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4bc0eb3a
  3. 13 4月, 2016 1 次提交
  4. 12 4月, 2016 8 次提交
    • D
      nl80211: check netlink protocol in socket release notification · 8f815cdd
      Dmitry Ivanov 提交于
      A non-privileged user can create a netlink socket with the same port_id as
      used by an existing open nl80211 netlink socket (e.g. as used by a hostapd
      process) with a different protocol number.
      
      Closing this socket will then lead to the notification going to nl80211's
      socket release notification handler, and possibly cause an action such as
      removing a virtual interface.
      
      Fix this issue by checking that the netlink protocol is NETLINK_GENERIC.
      Since generic netlink has no notifier chain of its own, we can't fix the
      problem more generically.
      
      Fixes: 026331c4 ("cfg80211/mac80211: allow registering for and sending action frames")
      Cc: stable@vger.kernel.org
      Signed-off-by: NDmitry Ivanov <dima@ubnt.com>
      [rewrite commit message]
      Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
      8f815cdd
    • S
      devlink: add missing install of header · 1ecf6890
      stephen hemminger 提交于
      The new devlink.h in uapi was not being installed by
      make headers_install
      Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      1ecf6890
    • D
      net: vrf: Fix dev refcnt leak due to IPv6 prefix route · 4f7f34ea
      David Ahern 提交于
      ifupdown2 found a kernel bug with IPv6 routes and movement from the main
      table to the VRF table. Sequence of events:
      
      Create the interface and add addresses:
          ip link add dev eth4.105 link eth4 type vlan id 105
          ip addr add dev eth4.105 8.105.105.10/24
          ip -6 addr add dev eth4.105 2008:105:105::10/64
      
      At this point IPv6 has inserted a prefix route in the main table even
      though the interface is 'down'. From there the VRF device is created:
          ip link add dev vrf105 type vrf table 105
          ip addr add dev vrf105 9.9.105.10/32
          ip -6 addr add dev vrf105 2000:9:105::10/128
          ip link set vrf105 up
      
      Then the interface is enslaved, while still in the 'down' state:
          ip link set dev eth4.105 master vrf105
      
      Since the device is down the VRF driver cycling the device does not
      send the NETDEV_UP and NETDEV_DOWN but rather the NETDEV_CHANGE event
      which does not flush the routes inserted prior.
      
      When the link is brought up
          ip link set dev eth4.105 up
      
      the prefix route is added in the VRF table, but does not remove
      the route from the main table.
      
      Fix by handling the NETDEV_CHANGEUPPER event similar what was implemented
      for IPv4 in 7f49e7a3 ("net: Flush local routes when device changes vrf
      association")
      
      Fixes: 35402e31 ("net: Add IPv6 support to VRF device")
      Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4f7f34ea
    • D
      net: vrf: Fix dst reference counting · 9ab179d8
      David Ahern 提交于
      Vivek reported a kernel exception deleting a VRF with an active
      connection through it. The root cause is that the socket has a cached
      reference to a dst that is destroyed. Converting the dst_destroy to
      dst_release and letting proper reference counting kick in does not
      work as the dst has a reference to the device which needs to be released
      as well.
      
      I talked to Hannes about this at netdev and he pointed out the ipv4 and
      ipv6 dst handling has dst_ifdown for just this scenario. Rather than
      continuing with the reinvented dst wheel in VRF just remove it and
      leverage the ipv4 and ipv6 versions.
      
      Fixes: 193125db ("net: Introduce VRF device driver")
      Fixes: 35402e31 ("net: Add IPv6 support to VRF device")
      Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      9ab179d8
    • D
      Merge branch 'tipc-fixes' · 10c3c022
      David S. Miller 提交于
      Jon Maloy says:
      
      ====================
      tipc: name distributor pernet queue
      
      Commit #1 fixes a potential issue with deferred binding table
      updates being pushed to the wrong namespace.
      
      Commit #2 solves a problem with deferred binding table updates
      remaining in the the defer queue after the issuing node has gone
      down.
      ====================
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      10c3c022
    • E
      tipc: purge deferred updates from dead nodes · ddb1d339
      Erik Hugne 提交于
      If a peer node becomes unavailable, in addition to removing the
      nametable entries from this node we also need to purge all deferred
      updates associated with this node.
      Signed-off-by: NErik Hugne <erik.hugne@gmail.com>
      Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ddb1d339
    • E
      tipc: make dist queue pernet · 541726ab
      Erik Hugne 提交于
      Nametable updates received from the network that cannot be applied
      immediately are placed on a defer queue. This queue is global to the
      TIPC module, which might cause problems when using TIPC in containers.
      To prevent nametable updates from escaping into the wrong namespace,
      we make the queue pernet instead.
      Signed-off-by: NErik Hugne <erik.hugne@gmail.com>
      Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      541726ab
    • H
      cxgb4: Stop Rx Queues before freeing it up · ebf4dc2b
      Hariprasad Shenai 提交于
      Stop all Ethernet RX Queues before freeing up various Ingress/Egress
      Queues, etc. We were seeing cases of Ingress Queues not getting serviced
      during the shutdown process leading to Ingress Paths jamming up through
      the chip and blocking the shutdown effort itself.
      
      One such case involved the Firmware sending a "Flush Token" through the
      ULP-TX -> ULP-RX path for an Ethernet TX Queue being freed in order to
      make sure there weren't any remaining TX Work Requests in the pipeline.
      But the return path was stalled by Ingress Data unable to be delivered to
      the Host because those Ingress Queues were no longer being serviced.
      
      Based on original work by Casey Leedom <leedom@chelsio.com>
      Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ebf4dc2b
  5. 11 4月, 2016 4 次提交
    • P
      net: stmmac: socfgpa: Ensure emac bit set in System Manger for PTP · 734e00fa
      Phil Reid 提交于
      When using the PTP fpga to hps clock source for the stmmac module
      the appropriate bit in the System Manager FPGA Interface Group register
      needs to be set. This is not set by the bootloader setup  when the
      HPS emac pins are being for this emac module.
      
      This allows the PTP clock to be sourced from the FPGA and also connects
      the PTP pps and ext trig signals to the stmmac PTP hardware.
      
      Patch proposed by Phil Collins.
      Signed-off-by: NPhil Reid <preid@electromag.com.au>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      734e00fa
    • D
      netlink: don't send NETLINK_URELEASE for unbound sockets · e2726020
      Dmitry Ivanov 提交于
      All existing users of NETLINK_URELEASE use it to clean up resources that
      were previously allocated to a socket via some command. As a result, no
      users require getting this notification for unbound sockets.
      
      Sending it for unbound sockets, however, is a problem because any user
      (including unprivileged users) can create a socket that uses the same ID
      as an existing socket. Binding this new socket will fail, but if the
      NETLINK_URELEASE notification is generated for such sockets, the users
      thereof will be tricked into thinking the socket that they allocated the
      resources for is closed.
      
      In the nl80211 case, this will cause destruction of virtual interfaces
      that still belong to an existing hostapd process; this is the case that
      Dmitry noticed. In the NFC case, it will cause a poll abort. In the case
      of netlink log/queue it will cause them to stop reporting events, as if
      NFULNL_CFG_CMD_UNBIND/NFQNL_CFG_CMD_UNBIND had been called.
      
      Fix this problem by checking that the socket is bound before generating
      the NETLINK_URELEASE notification.
      
      Cc: stable@vger.kernel.org
      Signed-off-by: NDmitry Ivanov <dima@ubnt.com>
      Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      e2726020
    • D
      decnet: Do not build routes to devices without decnet private data. · a36a0d40
      David S. Miller 提交于
      In particular, make sure we check for decnet private presence
      for loopback devices.
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a36a0d40
    • M
      sctp: avoid refreshing heartbeat timer too often · ba6f5e33
      Marcelo Ricardo Leitner 提交于
      Currently on high rate SCTP streams the heartbeat timer refresh can
      consume quite a lot of resources as timer updates are costly and it
      contains a random factor, which a) is also costly and b) invalidates
      mod_timer() optimization for not editing a timer to the same value.
      It may even cause the timer to be slightly advanced, for no good reason.
      
      As suggested by David Laight this patch now removes this timer update
      from hot path by leaving the timer on and re-evaluating upon its
      expiration if the heartbeat is still needed or not, similarly to what is
      done for TCP. If it's not needed anymore the timer is re-scheduled to
      the new timeout, considering the time already elapsed.
      
      For this, we now record the last tx timestamp per transport, updated in
      the same spots as hb timer was restarted on tx. Also split up
      sctp_transport_reset_timers into sctp_transport_reset_t3_rtx and
      sctp_transport_reset_hb_timer, so we can re-arm T3 without re-arming the
      heartbeat one.
      
      On loopback with MTU of 65535 and data chunks with 1636, so that we
      have a considerable amount of chunks without stressing system calls,
      netperf -t SCTP_STREAM -l 30, perf looked like this before:
      
      Samples: 103K of event 'cpu-clock', Event count (approx.): 25833000000
        Overhead  Command  Shared Object      Symbol
      +    6,15%  netperf  [kernel.vmlinux]   [k] copy_user_enhanced_fast_string
      -    5,43%  netperf  [kernel.vmlinux]   [k] _raw_write_unlock_irqrestore
         - _raw_write_unlock_irqrestore
            - 96,54% _raw_spin_unlock_irqrestore
               - 36,14% mod_timer
                  + 97,24% sctp_transport_reset_timers
                  + 2,76% sctp_do_sm
               + 33,65% __wake_up_sync_key
               + 28,77% sctp_ulpq_tail_event
               + 1,40% del_timer
            - 1,84% mod_timer
               + 99,03% sctp_transport_reset_timers
               + 0,97% sctp_do_sm
            + 1,50% sctp_ulpq_tail_event
      
      And after this patch, now with netperf -l 60:
      
      Samples: 230K of event 'cpu-clock', Event count (approx.): 57707250000
        Overhead  Command  Shared Object      Symbol
      +    5,65%  netperf  [kernel.vmlinux]   [k] memcpy_erms
      +    5,59%  netperf  [kernel.vmlinux]   [k] copy_user_enhanced_fast_string
      -    5,05%  netperf  [kernel.vmlinux]   [k] _raw_spin_unlock_irqrestore
         - _raw_spin_unlock_irqrestore
            + 49,89% __wake_up_sync_key
            + 45,68% sctp_ulpq_tail_event
            - 2,85% mod_timer
               + 76,51% sctp_transport_reset_t3_rtx
               + 23,49% sctp_do_sm
            + 1,55% del_timer
      +    2,50%  netperf  [sctp]             [k] sctp_datamsg_from_user
      +    2,26%  netperf  [sctp]             [k] sctp_sendmsg
      
      Throughput-wise, from 6800mbps without the patch to 7050mbps with it,
      ~3.7%.
      Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ba6f5e33
  6. 10 4月, 2016 4 次提交
    • S
      sh_eth: re-enable-E-MAC interrupts in sh_eth_set_ringparam() · 49dd48da
      Sergei Shtylyov 提交于
      The E-MAC interrupts are left disabled when the ring parameters are changed
      via 'ethtool'. In order to fix this, it's enough to call sh_eth_dev_init()
      with 'true' instead of 'false' for the second argument (which conveniently
      allows us to remove the following code re-enabling E-DMAC interrupts and
      reception).
      Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
      Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      49dd48da
    • L
      Merge tag 'tty-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty · 183c948a
      Linus Torvalds 提交于
      Pull tty fixes from Greg KH:
       "Here are two tty fixes for issues found.
      
        One was due to a merge error in 4.6-rc1, and the other a regression
        fix for UML consoles that broke in 4.6-rc1.
      
        Both have been in linux-next for a while"
      
      * tag 'tty-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
        tty: Fix merge of "tty: Refactor tty_open()"
        tty: Fix UML console breakage
      183c948a
    • L
      Merge tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb · ffb927d1
      Linus Torvalds 提交于
      Pull USB fixes from Greg KH:
       "Here are some USB fixes and new device ids for 4.6-rc3.
      
        Nothing major, the normal USB gadget fixes and usb-serial driver ids,
        along with some other fixes mixed in.  All except the USB serial ids
        have been tested in linux-next, the id additions should be fine as
        they are 'trivial'"
      
      * tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
        USB: option: add "D-Link DWM-221 B1" device id
        USB: serial: cp210x: Adding GE Healthcare Device ID
        USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
        usb: dwc3: keystone: drop dma_mask configuration
        usb: gadget: udc-core: remove manual dma configuration
        usb: dwc3: pci: add ID for one more Intel Broxton platform
        usb: renesas_usbhs: fix to avoid using a disabled ep in usbhsg_queue_done()
        usb: dwc2: do not override forced dr_mode in gadget setup
        usb: gadget: f_midi: unlock on error
        USB: digi_acceleport: do sanity checking for the number of ports
        USB: cypress_m8: add endpoint sanity check
        USB: mct_u232: add sanity checking in probe
        usb: fix regression in SuperSpeed endpoint descriptor parsing
        USB: usbip: fix potential out-of-bounds write
        usb: renesas_usbhs: disable TX IRQ before starting TX DMAC transfer
        usb: renesas_usbhs: avoid NULL pointer derefernce in usbhsf_pkt_handler()
        usb: gadget: f_midi: Fixed a bug when buflen was smaller than wMaxPacketSize
        usb: phy: qcom-8x16: fix regulator API abuse
        usb: ch9: Fix SSP Device Cap wFunctionalitySupport type
        usb: gadget: composite: Access SSP Dev Cap fields properly
        ...
      ffb927d1
    • L
      Merge tag 'staging-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging · c6e6e58c
      Linus Torvalds 提交于
      Pull staging and IIO driver fixes from Greg KH:
       "Here are some IIO driver fixes, along with two staging driver fixes
        for 4.6-rc3.
      
        One staging driver patch reverts the deletion of a driver that
        happened in 4.6-rc1.  We thought that laptop.org was dead, but it's
        still alive and kicking, and has users that were mad we broke their
        hardware by deleting a driver for their machines.  So that driver is
        added back and everyone is happy again.
      
        All of these have been in linux-next for a while with no reported
        issues"
      
      * tag 'staging-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
        Revert "Staging: olpc_dcon: Remove obsolete driver"
        staging/rdma/hfi1: select CRC32
        iio: gyro: bmg160: fix buffer read values
        iio: gyro: bmg160: fix endianness when reading axes
        iio: accel: bmc150: fix endianness when reading axes
        iio: st_magn: always define ST_MAGN_TRIGGER_SET_STATE
        iio: fix config watermark initial value
        iio: health: max30100: correct FIFO check condition
        iio: imu: Fix inv_mpu6050 dependencies
        iio: adc: Fix build error of missing devm_ioremap_resource on UM
        iio: light: apds9960: correct FIFO check condition
        iio: adc: max1363: correct reference voltage
        iio: adc: max1363: add missing adc to max1363_id
      c6e6e58c