Supported on all AVIVO-based asics.
Can be disabled via the new_pll module parameter:
new_pll=0 - disable
new_pll=1 - enable
enabled by default

[airlied: fixed to use do_div]
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@linux.ie>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@linux.ie>

We only want to return here for errors, the wait functions return
a positive timeout otherwise, which gets back to userspace and
causes X to crash here.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Also sets affected TTM calls up to not wait interruptible, since
that would cause an in-kernel spin until the TTM call succeeds, since
the Radeon code does not return to user-space when a signal is received.

Modifies interruptible fence waits to return -ERESTARTSYS rather than
-EBUSY when interrupted by a signal, since that's the (yet undocumented)
semantics required by the TTM sync object hooks.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Return -ERESTARTSYS instead of -ERESTART when interrupted by a signal.
The -ERESTARTSYS is converted to an -EINTR by the kernel signal layer
before returned to user-space.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This convert radeon to use new TTM validation API, it doesn't
really take advantage of it beside in the eviction case.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This change allow driver to pass sorted memory placement,
from most prefered placement to least prefered placement.
In order to avoid long function prototype a structure is
used to gather memory placement informations such as range
restriction (if you need a buffer to be in given range).
Range restriction is determined by fpfn & lpfn which are
the first page and last page number btw which allocation
can happen. If those fields are set to 0 ttm will assume
buffer can be put anywhere in the address space (thus it
avoids putting a burden on the driver to always properly
set those fields).

This patch also factor few functions like evicting first
entry of lru list or getting a memory space. This avoid
code duplication.

V2: Change API to use placement flags and array instead
    of packing placement order into a quadword.
V3: Make sure we set the appropriate mem.placement flag
    when validating or allocation memory space.

[Pending Thomas Hellstrom further review but okay
from preliminary review so far].
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

These are required for changes to TTM.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The object rework moved the tiling flag setup around wrongly,
so tiling we getting setup then overwritten by fb format.

Fixes regression with drm-radeon-next on rv530 laptop tiling test.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Entries in the i2c table aren't always ordered
by id.  This allows us to remove some quirks
that are no longer needed.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

entries in the ss table aren't always ordered
by id.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Don't add dac load detection property to DVI-D
- Make sure i2c info is valid before adding DP aux chan bus
- Don't create scaling_mode_property twice
- fix typo that prevented coherent and load detection from working
- add coherent prop to DP (for dp->dvi adapters)
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If we don't need the zone we need to free it.
Acked-By: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Sometimes we will use a crtc for integerated LVDS, which is different with
that assigned by BIOS. If we want to get flicker-free transitions,
then we could read out the current state for it and set our current state
accordingly.

But it is true that if we aren't reading current state out, we do need
to turn everything off before modesetting.  Otherwise the clocks can get very
angry and we get things worse than a flicker at boot.
In fact we also do the similar thing in UMS mode. We will disable all the
possible outputs/crtcs for the first modesetting.

So we disable all the possible outputs/crtcs before entering the KMS mode.
Before we configure connector/encoder/crtc, the function of
drm_helper_disable_unused_function can disable all the possible outputs/crtcs.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Reviewed-by: NEric Anholt <eric@anholt.net>
Reviewed-by: NRafal Milecki <zajec5@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This merges the radeon KMS DisplayPort and hotplug detect support.

Tested on RV635 DP card with a Dell 2408 monitor.

Conflicts:
	drivers/gpu/drm/drm_fb_helper.c

This merges all the radeon changes that weren't reliant on core-next.

This merges the upstream Intel tree and fixes up numerous conflicts
due to patches merged into Linus tree later in -rc cycle.

Conflicts:
	drivers/char/agp/intel-agp.c
	drivers/gpu/drm/drm_dp_i2c_helper.c
	drivers/gpu/drm/i915/i915_irq.c
	drivers/gpu/drm/i915/i915_suspend.c

Bring all core drm changes into 2.6.32 tree and resolve
the conflict that occurs.

Conflicts:
	drivers/gpu/drm/drm_fb_helper.c

crtc may be undefined at this point.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This enabled interrupt driven hpd support for all
radeon chips.  Assuming the hpd pin is wired up
correctly, the driver will generate uevents on
digital monitor connect and disconnect and retrain
DP monitors automatically.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This just adds the functionality, it's not hooked up
yet.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This just adds the functionality, it's not hooked up
yet.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This just adds the functionality, it's not hooked up
yet.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This populates the connectors with HPD (Hot Plug Detect)
information.  This will be used in subsequent patches
for automatic digital monitor connect/disconnect handling.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

only return connected if there is actually a
monitor connected.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NDave Airlie <airlied@redhat.com>

This moves the radeon DP link training call to happen when we
dpms on the encoder not when we set the mode.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This fix reorganises the initial DP link training slightly, and
actually makes DP work under kms here.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Not returning here caused us to get a display port version of 0 for everything
this caused power up to not get sent which ends up in a black screen.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This will be used laster when the encoder and transmitters
are set up.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- keep the atom i2c id in the i2c rec
- fix gpio regs for GPIO and MDGPIO on pre-avivo chips
- track whether the i2c line is hw capable
- track whether the i2c line uses the multimedia i2c block
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- dpcp -> dpcd
- fix up dig encoder routing
- aux transaction table takes delay in 10 usec units
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This is enough to retrieve EDID and DPCP.
Signed-off-by: NDave Airlie <airlied@redhat.com>

None of the in-tree drivers use user objects yet so this wasn't hitting
us.

Stanse found unreachable code in ttm_bo_add_ttm:
http://decibel.fi.muni.cz/~xslaby/stanse/error.cgi?db=32&id=714#l238Reported-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>