提交 40d69ba0 编写于 作者: S Sergei Shtylyov 提交者: Jeff Garzik

pata_hpt{37x|3x2n}: use pr_*(DRV_NAME ...) instead of printk(KERN_* ...)

... the same as the 'pata_hpt366' driver does.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
上级 bfdd7c58
......@@ -24,7 +24,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt37x"
#define DRV_VERSION "0.6.19"
#define DRV_VERSION "0.6.20"
struct hpt_clock {
u8 xfer_speed;
......@@ -863,7 +863,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
chip_table = &hpt372;
break;
default:
printk(KERN_ERR "pata_hpt37x: Unknown HPT366 subtype, "
pr_err(DRV_NAME ": Unknown HPT366 subtype, "
"please report (%d).\n", rev);
return -ENODEV;
}
......@@ -906,8 +906,8 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
*ppi = &info_hpt374_fn1;
break;
default:
printk(KERN_ERR
"pata_hpt37x: PCI table is bogus, please report (%d).\n",
pr_err(DRV_NAME
": PCI table is bogus, please report (%d).\n",
dev->device);
return -ENODEV;
}
......@@ -957,8 +957,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
u8 sr;
u32 total = 0;
printk(KERN_WARNING
"pata_hpt37x: BIOS has not set timing clocks.\n");
pr_warning(DRV_NAME ": BIOS has not set timing clocks.\n");
/* This is the process the HPT371 BIOS is reported to use */
for (i = 0; i < 128; i++) {
......@@ -1014,7 +1013,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
(f_high << 16) | f_low | 0x100);
}
if (adjust == 8) {
printk(KERN_ERR "pata_hpt37x: DPLL did not stabilize!\n");
pr_err(DRV_NAME ": DPLL did not stabilize!\n");
return -ENODEV;
}
if (dpll == 3)
......@@ -1022,8 +1021,8 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
else
private_data = (void *)hpt37x_timings_50;
printk(KERN_INFO "pata_hpt37x: bus clock %dMHz, using %dMHz DPLL.\n",
MHz[clock_slot], MHz[dpll]);
pr_info(DRV_NAME ": bus clock %dMHz, using %dMHz DPLL.\n",
MHz[clock_slot], MHz[dpll]);
} else {
private_data = (void *)chip_table->clocks[clock_slot];
/*
......@@ -1036,8 +1035,9 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
ppi[0] = &info_hpt370_33;
if (clock_slot < 2 && ppi[0] == &info_hpt370a)
ppi[0] = &info_hpt370a_33;
printk(KERN_INFO "pata_hpt37x: %s using %dMHz bus clock.\n",
chip_table->name, MHz[clock_slot]);
pr_info(DRV_NAME ": %s using %dMHz bus clock.\n",
chip_table->name, MHz[clock_slot]);
}
/* Now kick off ATA set up */
......
......@@ -25,7 +25,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_hpt3x2n"
#define DRV_VERSION "0.3.13"
#define DRV_VERSION "0.3.14"
enum {
HPT_PCI_FAST = (1 << 31),
......@@ -418,7 +418,7 @@ static int hpt3x2n_pci_clock(struct pci_dev *pdev)
u16 sr;
u32 total = 0;
printk(KERN_WARNING "pata_hpt3x2n: BIOS clock data not set.\n");
pr_warning(DRV_NAME ": BIOS clock data not set.\n");
/* This is the process the HPT371 BIOS is reported to use */
for (i = 0; i < 128; i++) {
......@@ -528,8 +528,7 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
ppi[0] = &info_hpt372n;
break;
default:
printk(KERN_ERR
"pata_hpt3x2n: PCI table is bogus please report (%d).\n",
pr_err(DRV_NAME ": PCI table is bogus, please report (%d).\n",
dev->device);
return -ENODEV;
}
......@@ -579,12 +578,11 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
}
if (adjust == 8) {
printk(KERN_ERR "pata_hpt3x2n: DPLL did not stabilize!\n");
pr_err(DRV_NAME ": DPLL did not stabilize!\n");
return -ENODEV;
}
printk(KERN_INFO "pata_hpt37x: bus clock %dMHz, using 66MHz DPLL.\n",
pci_mhz);
pr_info(DRV_NAME ": bus clock %dMHz, using 66MHz DPLL.\n", pci_mhz);
/*
* Set our private data up. We only need a few flags
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册