提交 2514183d 编写于 作者: H Haavard Skinnemoen 提交者: Linus Torvalds

[PATCH] AVR32 MTD: AT49BV6416 platform device for ATSTK1000

FRegister a platform device for the AT49BV6416 NOR flash chip on the ATSTK1000
development board for use by the physmap MTD driver.

The SMC timings are set up before the platform device is registered so that no
board-specific mapping driver is necessary.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
上级 bc157b75
obj-y += setup.o spi.o
obj-y += setup.o spi.o flash.o
obj-$(CONFIG_BOARD_ATSTK1002) += atstk1002.o
/*
* ATSTK1000 board-specific flash initialization
*
* Copyright (C) 2005-2006 Atmel Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <asm/arch/smc.h>
static struct smc_config flash_config __initdata = {
.ncs_read_setup = 0,
.nrd_setup = 40,
.ncs_write_setup = 0,
.nwe_setup = 10,
.ncs_read_pulse = 80,
.nrd_pulse = 40,
.ncs_write_pulse = 65,
.nwe_pulse = 55,
.read_cycle = 120,
.write_cycle = 120,
.bus_width = 2,
.nrd_controlled = 1,
.nwe_controlled = 1,
.byte_write = 1,
};
static struct mtd_partition flash_parts[] = {
{
.name = "u-boot",
.offset = 0x00000000,
.size = 0x00020000, /* 128 KiB */
.mask_flags = MTD_WRITEABLE,
},
{
.name = "root",
.offset = 0x00020000,
.size = 0x007d0000,
},
{
.name = "env",
.offset = 0x007f0000,
.size = 0x00010000,
.mask_flags = MTD_WRITEABLE,
},
};
static struct physmap_flash_data flash_data = {
.width = 2,
.nr_parts = ARRAY_SIZE(flash_parts),
.parts = flash_parts,
};
static struct resource flash_resource = {
.start = 0x00000000,
.end = 0x007fffff,
.flags = IORESOURCE_MEM,
};
static struct platform_device flash_device = {
.name = "physmap-flash",
.id = 0,
.resource = &flash_resource,
.num_resources = 1,
.dev = {
.platform_data = &flash_data,
},
};
/* This needs to be called after the SMC has been initialized */
static int __init atstk1000_flash_init(void)
{
int ret;
ret = smc_set_configuration(0, &flash_config);
if (ret < 0) {
printk(KERN_ERR "atstk1000: failed to set NOR flash timing\n");
return ret;
}
platform_device_register(&flash_device);
return 0;
}
device_initcall(atstk1000_flash_init);
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册