diff --git a/drivers/phy/motorola/phy-cpcap-usb.c b/drivers/phy/motorola/phy-cpcap-usb.c
index ead06c6c26019a91424a7e6be990f9ed7a8dbb0f..12e71a315a2cba315cb4f1c9b28422e3cbc8b93f 100644
--- a/drivers/phy/motorola/phy-cpcap-usb.c
+++ b/drivers/phy/motorola/phy-cpcap-usb.c
@@ -115,7 +115,7 @@ struct cpcap_usb_ints_state {
 enum cpcap_gpio_mode {
 	CPCAP_DM_DP,
 	CPCAP_MDM_RX_TX,
-	CPCAP_UNKNOWN,
+	CPCAP_UNKNOWN_DISABLED,	/* Seems to disable USB lines */
 	CPCAP_OTG_DM_DP,
 };
 
@@ -134,6 +134,8 @@ struct cpcap_phy_ddata {
 	struct iio_channel *id;
 	struct regulator *vusb;
 	atomic_t active;
+	unsigned int vbus_provider:1;
+	unsigned int docked:1;
 };
 
 static bool cpcap_usb_vbus_valid(struct cpcap_phy_ddata *ddata)
@@ -207,6 +209,19 @@ static int cpcap_phy_get_ints_state(struct cpcap_phy_ddata *ddata,
 static int cpcap_usb_set_uart_mode(struct cpcap_phy_ddata *ddata);
 static int cpcap_usb_set_usb_mode(struct cpcap_phy_ddata *ddata);
 
+static void cpcap_usb_try_musb_mailbox(struct cpcap_phy_ddata *ddata,
+				       enum musb_vbus_id_status status)
+{
+	int error;
+
+	error = musb_mailbox(status);
+	if (!error)
+		return;
+
+	dev_dbg(ddata->dev, "%s: musb_mailbox failed: %i\n",
+		__func__, error);
+}
+
 static void cpcap_usb_detect(struct work_struct *work)
 {
 	struct cpcap_phy_ddata *ddata;
@@ -220,16 +235,66 @@ static void cpcap_usb_detect(struct work_struct *work)
 	if (error)
 		return;
 
-	if (s.id_ground) {
-		dev_dbg(ddata->dev, "id ground, USB host mode\n");
+	vbus = cpcap_usb_vbus_valid(ddata);
+
+	/* We need to kick the VBUS as USB A-host */
+	if (s.id_ground && ddata->vbus_provider) {
+		dev_dbg(ddata->dev, "still in USB A-host mode, kicking VBUS\n");
+
+		cpcap_usb_try_musb_mailbox(ddata, MUSB_ID_GROUND);
+
+		error = regmap_update_bits(ddata->reg, CPCAP_REG_USBC3,
+					   CPCAP_BIT_VBUSSTBY_EN |
+					   CPCAP_BIT_VBUSEN_SPI,
+					   CPCAP_BIT_VBUSEN_SPI);
+		if (error)
+			goto out_err;
+
+		return;
+	}
+
+	if (vbus && s.id_ground && ddata->docked) {
+		dev_dbg(ddata->dev, "still docked as A-host, signal ID down\n");
+
+		cpcap_usb_try_musb_mailbox(ddata, MUSB_ID_GROUND);
+
+		return;
+	}
+
+	/* No VBUS needed with docks */
+	if (vbus && s.id_ground && !ddata->vbus_provider) {
+		dev_dbg(ddata->dev, "connected to a dock\n");
+
+		ddata->docked = true;
+
 		error = cpcap_usb_set_usb_mode(ddata);
 		if (error)
 			goto out_err;
 
-		error = musb_mailbox(MUSB_ID_GROUND);
+		cpcap_usb_try_musb_mailbox(ddata, MUSB_ID_GROUND);
+
+		/*
+		 * Force check state again after musb has reoriented,
+		 * otherwise devices won't enumerate after loading PHY
+		 * driver.
+		 */
+		schedule_delayed_work(&ddata->detect_work,
+				      msecs_to_jiffies(1000));
+
+		return;
+	}
+
+	if (s.id_ground && !ddata->docked) {
+		dev_dbg(ddata->dev, "id ground, USB host mode\n");
+
+		ddata->vbus_provider = true;
+
+		error = cpcap_usb_set_usb_mode(ddata);
 		if (error)
 			goto out_err;
 
+		cpcap_usb_try_musb_mailbox(ddata, MUSB_ID_GROUND);
+
 		error = regmap_update_bits(ddata->reg, CPCAP_REG_USBC3,
 					   CPCAP_BIT_VBUSSTBY_EN |
 					   CPCAP_BIT_VBUSEN_SPI,
@@ -248,43 +313,26 @@ static void cpcap_usb_detect(struct work_struct *work)
 
 	vbus = cpcap_usb_vbus_valid(ddata);
 
+	/* Otherwise assume we're connected to a USB host */
 	if (vbus) {
-		/* Are we connected to a docking station with vbus? */
-		if (s.id_ground) {
-			dev_dbg(ddata->dev, "connected to a dock\n");
-
-			/* No VBUS needed with docks */
-			error = cpcap_usb_set_usb_mode(ddata);
-			if (error)
-				goto out_err;
-			error = musb_mailbox(MUSB_ID_GROUND);
-			if (error)
-				goto out_err;
-
-			return;
-		}
-
-		/* Otherwise assume we're connected to a USB host */
 		dev_dbg(ddata->dev, "connected to USB host\n");
 		error = cpcap_usb_set_usb_mode(ddata);
 		if (error)
 			goto out_err;
-		error = musb_mailbox(MUSB_VBUS_VALID);
-		if (error)
-			goto out_err;
+		cpcap_usb_try_musb_mailbox(ddata, MUSB_VBUS_VALID);
 
 		return;
 	}
 
+	ddata->vbus_provider = false;
+	ddata->docked = false;
+	cpcap_usb_try_musb_mailbox(ddata, MUSB_VBUS_OFF);
+
 	/* Default to debug UART mode */
 	error = cpcap_usb_set_uart_mode(ddata);
 	if (error)
 		goto out_err;
 
-	error = musb_mailbox(MUSB_VBUS_OFF);
-	if (error)
-		goto out_err;
-
 	dev_dbg(ddata->dev, "set UART mode\n");
 
 	return;
@@ -376,7 +424,8 @@ static int cpcap_usb_set_uart_mode(struct cpcap_phy_ddata *ddata)
 {
 	int error;
 
-	error = cpcap_usb_gpio_set_mode(ddata, CPCAP_DM_DP);
+	/* Disable lines to prevent glitches from waking up mdm6600 */
+	error = cpcap_usb_gpio_set_mode(ddata, CPCAP_UNKNOWN_DISABLED);
 	if (error)
 		goto out_err;
 
@@ -403,6 +452,11 @@ static int cpcap_usb_set_uart_mode(struct cpcap_phy_ddata *ddata)
 	if (error)
 		goto out_err;
 
+	/* Enable UART mode */
+	error = cpcap_usb_gpio_set_mode(ddata, CPCAP_DM_DP);
+	if (error)
+		goto out_err;
+
 	return 0;
 
 out_err:
@@ -415,7 +469,8 @@ static int cpcap_usb_set_usb_mode(struct cpcap_phy_ddata *ddata)
 {
 	int error;
 
-	error = cpcap_usb_gpio_set_mode(ddata, CPCAP_OTG_DM_DP);
+	/* Disable lines to prevent glitches from waking up mdm6600 */
+	error = cpcap_usb_gpio_set_mode(ddata, CPCAP_UNKNOWN_DISABLED);
 	if (error)
 		return error;
 
@@ -434,12 +489,6 @@ static int cpcap_usb_set_usb_mode(struct cpcap_phy_ddata *ddata)
 	if (error)
 		goto out_err;
 
-	error = regmap_update_bits(ddata->reg, CPCAP_REG_USBC2,
-				   CPCAP_BIT_USBXCVREN,
-				   CPCAP_BIT_USBXCVREN);
-	if (error)
-		goto out_err;
-
 	error = regmap_update_bits(ddata->reg, CPCAP_REG_USBC3,
 				   CPCAP_BIT_PU_SPI |
 				   CPCAP_BIT_DMPD_SPI |
@@ -455,6 +504,11 @@ static int cpcap_usb_set_usb_mode(struct cpcap_phy_ddata *ddata)
 	if (error)
 		goto out_err;
 
+	/* Enable USB mode */
+	error = cpcap_usb_gpio_set_mode(ddata, CPCAP_OTG_DM_DP);
+	if (error)
+		goto out_err;
+
 	return 0;
 
 out_err:
@@ -649,9 +703,7 @@ static int cpcap_usb_phy_remove(struct platform_device *pdev)
 	if (error)
 		dev_err(ddata->dev, "could not set UART mode\n");
 
-	error = musb_mailbox(MUSB_VBUS_OFF);
-	if (error)
-		dev_err(ddata->dev, "could not set mailbox\n");
+	cpcap_usb_try_musb_mailbox(ddata, MUSB_VBUS_OFF);
 
 	usb_remove_phy(&ddata->phy);
 	cancel_delayed_work_sync(&ddata->detect_work);
diff --git a/drivers/phy/motorola/phy-mapphone-mdm6600.c b/drivers/phy/motorola/phy-mapphone-mdm6600.c
index ee184d5607bdb39240b2729b82688ef67501df06..f20524f0c21d9aea86013601ec47c381bf32db26 100644
--- a/drivers/phy/motorola/phy-mapphone-mdm6600.c
+++ b/drivers/phy/motorola/phy-mapphone-mdm6600.c
@@ -200,7 +200,7 @@ static void phy_mdm6600_status(struct work_struct *work)
 	struct phy_mdm6600 *ddata;
 	struct device *dev;
 	DECLARE_BITMAP(values, PHY_MDM6600_NR_STATUS_LINES);
-	int error, i, val = 0;
+	int error;
 
 	ddata = container_of(work, struct phy_mdm6600, status_work.work);
 	dev = ddata->dev;
@@ -212,16 +212,11 @@ static void phy_mdm6600_status(struct work_struct *work)
 	if (error)
 		return;
 
-	for (i = 0; i < PHY_MDM6600_NR_STATUS_LINES; i++) {
-		val |= test_bit(i, values) << i;
-		dev_dbg(ddata->dev, "XXX %s: i: %i values[i]: %i val: %i\n",
-			__func__, i, test_bit(i, values), val);
-	}
-	ddata->status = values[0];
+	ddata->status = values[0] & ((1 << PHY_MDM6600_NR_STATUS_LINES) - 1);
 
 	dev_info(dev, "modem status: %i %s\n",
 		 ddata->status,
-		 phy_mdm6600_status_name[ddata->status & 7]);
+		 phy_mdm6600_status_name[ddata->status]);
 	complete(&ddata->ack);
 }
 
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 091e20303a14d6b3569eb806eb3bf72beb56ae4e..66f91726b8b24b4ded24806e2e701ff4bc066904 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -66,7 +66,7 @@
 /* QPHY_V3_PCS_MISC_CLAMP_ENABLE register bits */
 #define CLAMP_EN				BIT(0) /* enables i/o clamp_n */
 
-#define PHY_INIT_COMPLETE_TIMEOUT		1000
+#define PHY_INIT_COMPLETE_TIMEOUT		10000
 #define POWER_DOWN_DELAY_US_MIN			10
 #define POWER_DOWN_DELAY_US_MAX			11
 
diff --git a/drivers/phy/rockchip/phy-rockchip-inno-hdmi.c b/drivers/phy/rockchip/phy-rockchip-inno-hdmi.c
index 2b97fb1185a00e68b41858c15a8a99b0ae7303b6..9ca20c947283de2f5d03866aa404c0411b2eb72c 100644
--- a/drivers/phy/rockchip/phy-rockchip-inno-hdmi.c
+++ b/drivers/phy/rockchip/phy-rockchip-inno-hdmi.c
@@ -603,6 +603,8 @@ static long inno_hdmi_phy_rk3228_clk_round_rate(struct clk_hw *hw,
 {
 	const struct pre_pll_config *cfg = pre_pll_cfg_table;
 
+	rate = (rate / 1000) * 1000;
+
 	for (; cfg->pixclock != 0; cfg++)
 		if (cfg->pixclock == rate && !cfg->fracdiv)
 			break;
@@ -755,6 +757,8 @@ static long inno_hdmi_phy_rk3328_clk_round_rate(struct clk_hw *hw,
 {
 	const struct pre_pll_config *cfg = pre_pll_cfg_table;
 
+	rate = (rate / 1000) * 1000;
+
 	for (; cfg->pixclock != 0; cfg++)
 		if (cfg->pixclock == rate)
 			break;
diff --git a/drivers/usb/cdns3/gadget.c b/drivers/usb/cdns3/gadget.c
index 4c1e755093039d0582ca30922d620009441aed0c..02f6ca2cb1ba1c99d26efd2e225889b0f9c3908d 100644
--- a/drivers/usb/cdns3/gadget.c
+++ b/drivers/usb/cdns3/gadget.c
@@ -1375,13 +1375,10 @@ static void cdns3_check_usb_interrupt_proceed(struct cdns3_device *priv_dev,
  */
 static irqreturn_t cdns3_device_irq_handler(int irq, void *data)
 {
-	struct cdns3_device *priv_dev;
-	struct cdns3 *cdns = data;
+	struct cdns3_device *priv_dev = data;
 	irqreturn_t ret = IRQ_NONE;
 	u32 reg;
 
-	priv_dev = cdns->gadget_dev;
-
 	/* check USB device interrupt */
 	reg = readl(&priv_dev->regs->usb_ists);
 	if (reg) {
@@ -1419,14 +1416,12 @@ static irqreturn_t cdns3_device_irq_handler(int irq, void *data)
  */
 static irqreturn_t cdns3_device_thread_irq_handler(int irq, void *data)
 {
-	struct cdns3_device *priv_dev;
-	struct cdns3 *cdns = data;
+	struct cdns3_device *priv_dev = data;
 	irqreturn_t ret = IRQ_NONE;
 	unsigned long flags;
 	int bit;
 	u32 reg;
 
-	priv_dev = cdns->gadget_dev;
 	spin_lock_irqsave(&priv_dev->lock, flags);
 
 	reg = readl(&priv_dev->regs->usb_ists);
@@ -2539,7 +2534,7 @@ void cdns3_gadget_exit(struct cdns3 *cdns)
 
 	priv_dev = cdns->gadget_dev;
 
-	devm_free_irq(cdns->dev, cdns->dev_irq, cdns);
+	devm_free_irq(cdns->dev, cdns->dev_irq, priv_dev);
 
 	pm_runtime_mark_last_busy(cdns->dev);
 	pm_runtime_put_autosuspend(cdns->dev);
@@ -2710,7 +2705,8 @@ static int __cdns3_gadget_init(struct cdns3 *cdns)
 	ret = devm_request_threaded_irq(cdns->dev, cdns->dev_irq,
 					cdns3_device_irq_handler,
 					cdns3_device_thread_irq_handler,
-					IRQF_SHARED, dev_name(cdns->dev), cdns);
+					IRQF_SHARED, dev_name(cdns->dev),
+					cdns->gadget_dev);
 
 	if (ret)
 		goto err0;
diff --git a/drivers/usb/chipidea/host.c b/drivers/usb/chipidea/host.c
index b45ceb91c735e71a6f4db81e5dd24aa3a77819e8..48e4a5ca183591fd577b9e3cc9e0174a3b739beb 100644
--- a/drivers/usb/chipidea/host.c
+++ b/drivers/usb/chipidea/host.c
@@ -26,6 +26,7 @@ static int (*orig_bus_suspend)(struct usb_hcd *hcd);
 
 struct ehci_ci_priv {
 	struct regulator *reg_vbus;
+	bool enabled;
 };
 
 static int ehci_ci_portpower(struct usb_hcd *hcd, int portnum, bool enable)
@@ -37,7 +38,7 @@ static int ehci_ci_portpower(struct usb_hcd *hcd, int portnum, bool enable)
 	int ret = 0;
 	int port = HCS_N_PORTS(ehci->hcs_params);
 
-	if (priv->reg_vbus) {
+	if (priv->reg_vbus && enable != priv->enabled) {
 		if (port > 1) {
 			dev_warn(dev,
 				"Not support multi-port regulator control\n");
@@ -53,6 +54,7 @@ static int ehci_ci_portpower(struct usb_hcd *hcd, int portnum, bool enable)
 				enable ? "enable" : "disable", ret);
 			return ret;
 		}
+		priv->enabled = enable;
 	}
 
 	if (enable && (ci->platdata->phy_mode == USBPHY_INTERFACE_MODE_HSIC)) {
diff --git a/drivers/usb/core/config.c b/drivers/usb/core/config.c
index 5f40117e68e76e07949d95182abfe39af7936a21..26bc05e48d8a7414121dd348e7dfc06e6916cedc 100644
--- a/drivers/usb/core/config.c
+++ b/drivers/usb/core/config.c
@@ -203,9 +203,58 @@ static const unsigned short super_speed_maxpacket_maxes[4] = {
 	[USB_ENDPOINT_XFER_INT] = 1024,
 };
 
-static int usb_parse_endpoint(struct device *ddev, int cfgno, int inum,
-    int asnum, struct usb_host_interface *ifp, int num_ep,
-    unsigned char *buffer, int size)
+static bool endpoint_is_duplicate(struct usb_endpoint_descriptor *e1,
+		struct usb_endpoint_descriptor *e2)
+{
+	if (e1->bEndpointAddress == e2->bEndpointAddress)
+		return true;
+
+	if (usb_endpoint_xfer_control(e1) || usb_endpoint_xfer_control(e2)) {
+		if (usb_endpoint_num(e1) == usb_endpoint_num(e2))
+			return true;
+	}
+
+	return false;
+}
+
+/*
+ * Check for duplicate endpoint addresses in other interfaces and in the
+ * altsetting currently being parsed.
+ */
+static bool config_endpoint_is_duplicate(struct usb_host_config *config,
+		int inum, int asnum, struct usb_endpoint_descriptor *d)
+{
+	struct usb_endpoint_descriptor *epd;
+	struct usb_interface_cache *intfc;
+	struct usb_host_interface *alt;
+	int i, j, k;
+
+	for (i = 0; i < config->desc.bNumInterfaces; ++i) {
+		intfc = config->intf_cache[i];
+
+		for (j = 0; j < intfc->num_altsetting; ++j) {
+			alt = &intfc->altsetting[j];
+
+			if (alt->desc.bInterfaceNumber == inum &&
+					alt->desc.bAlternateSetting != asnum)
+				continue;
+
+			for (k = 0; k < alt->desc.bNumEndpoints; ++k) {
+				epd = &alt->endpoint[k].desc;
+
+				if (endpoint_is_duplicate(epd, d))
+					return true;
+			}
+		}
+	}
+
+	return false;
+}
+
+static int usb_parse_endpoint(struct device *ddev, int cfgno,
+		struct usb_host_config *config, int inum, int asnum,
+		struct usb_host_interface *ifp, int num_ep,
+		unsigned char *buffer, int size)
 {
 	unsigned char *buffer0 = buffer;
 	struct usb_endpoint_descriptor *d;
@@ -242,13 +291,10 @@ static int usb_parse_endpoint(struct device *ddev, int cfgno, int inum,
 		goto skip_to_next_endpoint_or_interface_descriptor;
 
 	/* Check for duplicate endpoint addresses */
-	for (i = 0; i < ifp->desc.bNumEndpoints; ++i) {
-		if (ifp->endpoint[i].desc.bEndpointAddress ==
-		    d->bEndpointAddress) {
-			dev_warn(ddev, "config %d interface %d altsetting %d has a duplicate endpoint with address 0x%X, skipping\n",
-			    cfgno, inum, asnum, d->bEndpointAddress);
-			goto skip_to_next_endpoint_or_interface_descriptor;
-		}
+	if (config_endpoint_is_duplicate(config, inum, asnum, d)) {
+		dev_warn(ddev, "config %d interface %d altsetting %d has a duplicate endpoint with address 0x%X, skipping\n",
+				cfgno, inum, asnum, d->bEndpointAddress);
+		goto skip_to_next_endpoint_or_interface_descriptor;
 	}
 
 	endpoint = &ifp->endpoint[ifp->desc.bNumEndpoints];
@@ -346,12 +392,16 @@ static int usb_parse_endpoint(struct device *ddev, int cfgno, int inum,
 			endpoint->desc.wMaxPacketSize = cpu_to_le16(8);
 	}
 
-	/* Validate the wMaxPacketSize field */
+	/*
+	 * Validate the wMaxPacketSize field.
+	 * Some devices have isochronous endpoints in altsetting 0;
+	 * the USB-2 spec requires such endpoints to have wMaxPacketSize = 0
+	 * (see the end of section 5.6.3), so don't warn about them.
+	 */
 	maxp = usb_endpoint_maxp(&endpoint->desc);
-	if (maxp == 0) {
-		dev_warn(ddev, "config %d interface %d altsetting %d endpoint 0x%X has wMaxPacketSize 0, skipping\n",
+	if (maxp == 0 && !(usb_endpoint_xfer_isoc(d) && asnum == 0)) {
+		dev_warn(ddev, "config %d interface %d altsetting %d endpoint 0x%X has invalid wMaxPacketSize 0\n",
 		    cfgno, inum, asnum, d->bEndpointAddress);
-		goto skip_to_next_endpoint_or_interface_descriptor;
 	}
 
 	/* Find the highest legal maxpacket size for this endpoint */
@@ -522,8 +572,8 @@ static int usb_parse_interface(struct device *ddev, int cfgno,
 		if (((struct usb_descriptor_header *) buffer)->bDescriptorType
 		     == USB_DT_INTERFACE)
 			break;
-		retval = usb_parse_endpoint(ddev, cfgno, inum, asnum, alt,
-		    num_ep, buffer, size);
+		retval = usb_parse_endpoint(ddev, cfgno, config, inum, asnum,
+				alt, num_ep, buffer, size);
 		if (retval < 0)
 			return retval;
 		++n;
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index f229ad6952c0a941a9952fe619d847cf5ccab58b..8c4e5adbf82027fe1ce7292a08c0d274976272c9 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -2692,7 +2692,7 @@ static unsigned hub_is_wusb(struct usb_hub *hub)
 #define SET_ADDRESS_TRIES	2
 #define GET_DESCRIPTOR_TRIES	2
 #define SET_CONFIG_TRIES	(2 * (use_both_schemes + 1))
-#define USE_NEW_SCHEME(i, scheme)	((i) / 2 == (int)scheme)
+#define USE_NEW_SCHEME(i, scheme)	((i) / 2 == (int)(scheme))
 
 #define HUB_ROOT_RESET_TIME	60	/* times are in msec */
 #define HUB_SHORT_RESET_TIME	10
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index 0c960a97ea0214ed73e5fe018587aafb6c8d3d8f..154f3f3e8cff849754904721e2f0730f25fff7cd 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -2467,6 +2467,13 @@ static int dwc3_gadget_ep_reclaim_trb_linear(struct dwc3_ep *dep,
 
 static bool dwc3_gadget_ep_request_completed(struct dwc3_request *req)
 {
+	/*
+	 * For OUT direction, host may send less than the setup
+	 * length. Return true for all OUT requests.
+	 */
+	if (!req->direction)
+		return true;
+
 	return req->request.actual == req->request.length;
 }
 
diff --git a/drivers/usb/gadget/udc/Kconfig b/drivers/usb/gadget/udc/Kconfig
index ae70ce29d5e42d8e3a4e280de8a9b5ecc969adc9..797d6ace89943a0015a3814bef336b7dde724524 100644
--- a/drivers/usb/gadget/udc/Kconfig
+++ b/drivers/usb/gadget/udc/Kconfig
@@ -445,6 +445,7 @@ config USB_TEGRA_XUDC
 	tristate "NVIDIA Tegra Superspeed USB 3.0 Device Controller"
 	depends on ARCH_TEGRA || COMPILE_TEST
 	depends on PHY_TEGRA_XUSB
+	select USB_ROLE_SWITCH
 	help
 	 Enables NVIDIA Tegra USB 3.0 device mode controller driver.
 
diff --git a/drivers/usb/host/ohci-da8xx.c b/drivers/usb/host/ohci-da8xx.c
index 38183ac438c673871b08ecb485bcf6b20893bb18..1371b0c249ece0d4985222e74f91ea6caf637128 100644
--- a/drivers/usb/host/ohci-da8xx.c
+++ b/drivers/usb/host/ohci-da8xx.c
@@ -415,13 +415,17 @@ static int ohci_da8xx_probe(struct platform_device *pdev)
 	}
 
 	da8xx_ohci->oc_gpio = devm_gpiod_get_optional(dev, "oc", GPIOD_IN);
-	if (IS_ERR(da8xx_ohci->oc_gpio))
+	if (IS_ERR(da8xx_ohci->oc_gpio)) {
+		error = PTR_ERR(da8xx_ohci->oc_gpio);
 		goto err;
+	}
 
 	if (da8xx_ohci->oc_gpio) {
 		oc_irq = gpiod_to_irq(da8xx_ohci->oc_gpio);
-		if (oc_irq < 0)
+		if (oc_irq < 0) {
+			error = oc_irq;
 			goto err;
+		}
 
 		error = devm_request_threaded_irq(dev, oc_irq, NULL,
 				ohci_da8xx_oc_thread, IRQF_TRIGGER_RISING |
diff --git a/drivers/usb/musb/jz4740.c b/drivers/usb/musb/jz4740.c
index 5261f8dfedecd4c6fa4b7da20b43edce50cd0d62..e3b8c84ccdb80c6087e14dae2e3fca5e3c0122fd 100644
--- a/drivers/usb/musb/jz4740.c
+++ b/drivers/usb/musb/jz4740.c
@@ -75,14 +75,17 @@ static struct musb_hdrc_platform_data jz4740_musb_platform_data = {
 static int jz4740_musb_init(struct musb *musb)
 {
 	struct device *dev = musb->controller->parent;
+	int err;
 
 	if (dev->of_node)
 		musb->xceiv = devm_usb_get_phy_by_phandle(dev, "phys", 0);
 	else
 		musb->xceiv = devm_usb_get_phy(dev, USB_PHY_TYPE_USB2);
 	if (IS_ERR(musb->xceiv)) {
-		dev_err(dev, "No transceiver configured\n");
-		return PTR_ERR(musb->xceiv);
+		err = PTR_ERR(musb->xceiv);
+		if (err != -EPROBE_DEFER)
+			dev_err(dev, "No transceiver configured: %d", err);
+		return err;
 	}
 
 	/* Silicon does not implement ConfigData register.
diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c
index 15cca912c53e3e5849ac3f54b9f4ab8d57340d6a..5ebf30bd61bd1f4da6b45e0935d988f261a09f83 100644
--- a/drivers/usb/musb/musb_core.c
+++ b/drivers/usb/musb/musb_core.c
@@ -1840,6 +1840,9 @@ ATTRIBUTE_GROUPS(musb);
 #define MUSB_QUIRK_B_INVALID_VBUS_91	(MUSB_DEVCTL_BDEVICE | \
 					 (2 << MUSB_DEVCTL_VBUS_SHIFT) | \
 					 MUSB_DEVCTL_SESSION)
+#define MUSB_QUIRK_B_DISCONNECT_99	(MUSB_DEVCTL_BDEVICE | \
+					 (3 << MUSB_DEVCTL_VBUS_SHIFT) | \
+					 MUSB_DEVCTL_SESSION)
 #define MUSB_QUIRK_A_DISCONNECT_19	((3 << MUSB_DEVCTL_VBUS_SHIFT) | \
 					 MUSB_DEVCTL_SESSION)
 
@@ -1862,6 +1865,11 @@ static void musb_pm_runtime_check_session(struct musb *musb)
 	s = MUSB_DEVCTL_FSDEV | MUSB_DEVCTL_LSDEV |
 		MUSB_DEVCTL_HR;
 	switch (devctl & ~s) {
+	case MUSB_QUIRK_B_DISCONNECT_99:
+		musb_dbg(musb, "Poll devctl in case of suspend after disconnect\n");
+		schedule_delayed_work(&musb->irq_work,
+				      msecs_to_jiffies(1000));
+		break;
 	case MUSB_QUIRK_B_INVALID_VBUS_91:
 		if (musb->quirk_retries && !musb->flush_irq_work) {
 			musb_dbg(musb,
@@ -2310,6 +2318,9 @@ musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl)
 	musb_disable_interrupts(musb);
 	musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
 
+	/* MUSB_POWER_SOFTCONN might be already set, JZ4740 does this. */
+	musb_writeb(musb->mregs, MUSB_POWER, 0);
+
 	/* Init IRQ workqueue before request_irq */
 	INIT_DELAYED_WORK(&musb->irq_work, musb_irq_work);
 	INIT_DELAYED_WORK(&musb->deassert_reset_work, musb_deassert_reset);
diff --git a/drivers/usb/musb/musbhsdma.c b/drivers/usb/musb/musbhsdma.c
index 5fc6825745f21bd6246d71b99fd98d7313396f01..2d3751d885b429cb008e46dbfab5a295b815b794 100644
--- a/drivers/usb/musb/musbhsdma.c
+++ b/drivers/usb/musb/musbhsdma.c
@@ -425,7 +425,7 @@ struct dma_controller *musbhs_dma_controller_create(struct musb *musb,
 	controller->controller.channel_abort = dma_channel_abort;
 
 	if (request_irq(irq, dma_controller_irq, 0,
-			dev_name(musb->controller), &controller->controller)) {
+			dev_name(musb->controller), controller)) {
 		dev_err(dev, "request_irq %d failed!\n", irq);
 		musb_dma_controller_destroy(&controller->controller);
 
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index e9491d400a24fae06c90387f585a3c88e38a71bd..2d919d0e6e455955de9a163310c7863d28049e24 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -567,6 +567,9 @@ static void option_instat_callback(struct urb *urb);
 /* Interface must have two endpoints */
 #define NUMEP2		BIT(16)
 
+/* Device needs ZLP */
+#define ZLP		BIT(17)
+
 
 static const struct usb_device_id option_ids[] = {
 	{ USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_COLT) },
@@ -1172,6 +1175,8 @@ static const struct usb_device_id option_ids[] = {
 	  .driver_info = NCTRL(0) | RSVD(3) },
 	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1102, 0xff),	/* Telit ME910 (ECM) */
 	  .driver_info = NCTRL(0) },
+	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x110a, 0xff),	/* Telit ME910G1 */
+	  .driver_info = NCTRL(0) | RSVD(3) },
 	{ USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_LE910),
 	  .driver_info = NCTRL(0) | RSVD(1) | RSVD(2) },
 	{ USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_LE910_USBCFG4),
@@ -1196,6 +1201,8 @@ static const struct usb_device_id option_ids[] = {
 	  .driver_info = NCTRL(0) | RSVD(1) },
 	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1901, 0xff),	/* Telit LN940 (MBIM) */
 	  .driver_info = NCTRL(0) },
+	{ USB_DEVICE(TELIT_VENDOR_ID, 0x9010),				/* Telit SBL FN980 flashing device */
+	  .driver_info = NCTRL(0) | ZLP },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MF622, 0xff, 0xff, 0xff) }, /* ZTE WCDMA products */
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x0002, 0xff, 0xff, 0xff),
 	  .driver_info = RSVD(1) },
@@ -2097,6 +2104,9 @@ static int option_attach(struct usb_serial *serial)
 	if (!(device_flags & NCTRL(iface_desc->bInterfaceNumber)))
 		data->use_send_setup = 1;
 
+	if (device_flags & ZLP)
+		data->use_zlp = 1;
+
 	spin_lock_init(&data->susp_lock);
 
 	usb_set_serial_data(serial, data);
diff --git a/drivers/usb/serial/usb-wwan.h b/drivers/usb/serial/usb-wwan.h
index 1c120eaf4091c05c4f279d5e703177a906074965..934e9361cf6bb47b0c5f2bcf327597c321589c20 100644
--- a/drivers/usb/serial/usb-wwan.h
+++ b/drivers/usb/serial/usb-wwan.h
@@ -38,6 +38,7 @@ struct usb_wwan_intf_private {
 	spinlock_t susp_lock;
 	unsigned int suspended:1;
 	unsigned int use_send_setup:1;
+	unsigned int use_zlp:1;
 	int in_flight;
 	unsigned int open_ports;
 	void *private;
diff --git a/drivers/usb/serial/usb_wwan.c b/drivers/usb/serial/usb_wwan.c
index 7e855c87e4f7bb1a1364923cacf9a5f6ae970285..13be21aad2f40c7eefd5588a105364d38eeed4e9 100644
--- a/drivers/usb/serial/usb_wwan.c
+++ b/drivers/usb/serial/usb_wwan.c
@@ -461,6 +461,7 @@ static struct urb *usb_wwan_setup_urb(struct usb_serial_port *port,
 				      void (*callback) (struct urb *))
 {
 	struct usb_serial *serial = port->serial;
+	struct usb_wwan_intf_private *intfdata = usb_get_serial_data(serial);
 	struct urb *urb;
 
 	urb = usb_alloc_urb(0, GFP_KERNEL);	/* No ISO */
@@ -471,6 +472,9 @@ static struct urb *usb_wwan_setup_urb(struct usb_serial_port *port,
 			  usb_sndbulkpipe(serial->dev, endpoint) | dir,
 			  buf, len, callback, ctx);
 
+	if (intfdata->use_zlp && dir == USB_DIR_OUT)
+		urb->transfer_flags |= URB_ZERO_PACKET;
+
 	return urb;
 }
 
diff --git a/drivers/usb/typec/tcpm/tcpci.c b/drivers/usb/typec/tcpm/tcpci.c
index c1f7073a56de7329adafc115655a96be7740ff88..8b4ff9fff340c9a3a4f06c33a6446dfb778c6a53 100644
--- a/drivers/usb/typec/tcpm/tcpci.c
+++ b/drivers/usb/typec/tcpm/tcpci.c
@@ -432,20 +432,30 @@ irqreturn_t tcpci_irq(struct tcpci *tcpci)
 
 	if (status & TCPC_ALERT_RX_STATUS) {
 		struct pd_message msg;
-		unsigned int cnt;
+		unsigned int cnt, payload_cnt;
 		u16 header;
 
 		regmap_read(tcpci->regmap, TCPC_RX_BYTE_CNT, &cnt);
+		/*
+		 * 'cnt' corresponds to READABLE_BYTE_COUNT in section 4.4.14
+		 * of the TCPCI spec [Rev 2.0 Ver 1.0 October 2017] and is
+		 * defined in table 4-36 as one greater than the number of
+		 * bytes received. And that number includes the header. So:
+		 */
+		if (cnt > 3)
+			payload_cnt = cnt - (1 + sizeof(msg.header));
+		else
+			payload_cnt = 0;
 
 		tcpci_read16(tcpci, TCPC_RX_HDR, &header);
 		msg.header = cpu_to_le16(header);
 
-		if (WARN_ON(cnt > sizeof(msg.payload)))
-			cnt = sizeof(msg.payload);
+		if (WARN_ON(payload_cnt > sizeof(msg.payload)))
+			payload_cnt = sizeof(msg.payload);
 
-		if (cnt > 0)
+		if (payload_cnt > 0)
 			regmap_raw_read(tcpci->regmap, TCPC_RX_DATA,
-					&msg.payload, cnt);
+					&msg.payload, payload_cnt);
 
 		/* Read complete, clear RX status alert bit */
 		tcpci_write16(tcpci, TCPC_ALERT, TCPC_ALERT_RX_STATUS);
diff --git a/drivers/usb/typec/ucsi/ucsi.h b/drivers/usb/typec/ucsi/ucsi.h
index 8569bbd3762fdfde81e28a2b7cf7a36388f19fe0..831c9470bdc1f21227a662e06782c36ffd5c8afa 100644
--- a/drivers/usb/typec/ucsi/ucsi.h
+++ b/drivers/usb/typec/ucsi/ucsi.h
@@ -94,15 +94,15 @@ void ucsi_connector_change(struct ucsi *ucsi, u8 num);
 #define UCSI_ENABLE_NTFY_CMD_COMPLETE		BIT(16)
 #define UCSI_ENABLE_NTFY_EXT_PWR_SRC_CHANGE	BIT(17)
 #define UCSI_ENABLE_NTFY_PWR_OPMODE_CHANGE	BIT(18)
-#define UCSI_ENABLE_NTFY_CAP_CHANGE		BIT(19)
-#define UCSI_ENABLE_NTFY_PWR_LEVEL_CHANGE	BIT(20)
-#define UCSI_ENABLE_NTFY_PD_RESET_COMPLETE	BIT(21)
-#define UCSI_ENABLE_NTFY_CAM_CHANGE		BIT(22)
-#define UCSI_ENABLE_NTFY_BAT_STATUS_CHANGE	BIT(23)
-#define UCSI_ENABLE_NTFY_PARTNER_CHANGE		BIT(24)
-#define UCSI_ENABLE_NTFY_PWR_DIR_CHANGE		BIT(25)
-#define UCSI_ENABLE_NTFY_CONNECTOR_CHANGE	BIT(26)
-#define UCSI_ENABLE_NTFY_ERROR			BIT(27)
+#define UCSI_ENABLE_NTFY_CAP_CHANGE		BIT(21)
+#define UCSI_ENABLE_NTFY_PWR_LEVEL_CHANGE	BIT(22)
+#define UCSI_ENABLE_NTFY_PD_RESET_COMPLETE	BIT(23)
+#define UCSI_ENABLE_NTFY_CAM_CHANGE		BIT(24)
+#define UCSI_ENABLE_NTFY_BAT_STATUS_CHANGE	BIT(25)
+#define UCSI_ENABLE_NTFY_PARTNER_CHANGE		BIT(27)
+#define UCSI_ENABLE_NTFY_PWR_DIR_CHANGE		BIT(28)
+#define UCSI_ENABLE_NTFY_CONNECTOR_CHANGE	BIT(30)
+#define UCSI_ENABLE_NTFY_ERROR			BIT(31)
 #define UCSI_ENABLE_NTFY_ALL			0xdbe70000
 
 /* SET_UOR command bits */