HPT36x chip don't seem to have the channel enable bits, so prevent the IDE core
from checking them...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Michal Kepien <michal.kepien@poczta.onet.pl>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* fix ->speedproc to set the drive speed

* this driver doesn't support SWDMA so use the correct ->swdma_mask

* BUG() if an unsupported mode is passed to ->speedproc
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This driver doesn't support SWDMA so use the correct ->swdma_mask.

While at it:

* no need to call config_chipset_for_pio() in config_chipset_for_dma(),
  if DMA is not available config_chipset_for_pio() will be called
  by siimage_config_drive_for_dma() and if DMA is available
  config_siimage_chipset_for_pio() will be called by siimage_tune_chipset()

* remove needless config_chipset_for_pio() wrapper

* bump driver version
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* limit max PIO mode to PIO4, this driver doesn't support PIO5 and attempt
  to setup PIO5 by it821x_tuneproc() could result in incorrect PIO timings
  + incorrect base clock being set for controller in the passthrough mode

* move code limiting max PIO according to the pair device capabilities from
  config_it821x_chipset_for_pio() to it821x_tuneproc() so the check is also
  applied for mode change requests coming through ->tuneproc and ->speedproc
  interfaces

* set device speed in it821x_tuneproc()

* in it821x_tune_chipset() call it821x_tuneproc() also if the controller is
  in the smart mode (so the check for pair device max PIO is done)

* rename it821x_tuneproc() to it821x_tune_pio(), then add it821x_tuneproc()
  wrapper which does the max PIO mode check;  it worked by the pure luck
  previously, pio[4] and pio_want[4] arrays were used with index == 255
  so random PIO timings and base clock were set for the controller in the
  passthrough mode, thankfully PIO timings and base clock were corrected
  later by config_it821x_chipset_for_pio() call (but it was not called for
  PIO-only devices during resume and for user requested PIO autotuning)

* remove config_it821x_chipset_for_pio() call from config_chipset_for_dma()
  as the driver sets ->autotune to 1 and ->tuneproc does the proper job now

* convert the last user of config_it821x_chipset_for_pio() to use
  it821x_tuneproc(drive, 255) and remove no longer needed function

While at it:

* fix few comments

* bump driver version
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There is no reason to limit DMA to ide_cdrom type devices.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

If DMA tuning fails always set the best PIO mode.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Teach the driver's tuneproc() method to do PIO auto-runing properly since it
treated 5 instead of 255 as auto-tune request, and also passed the mode limit
of PIO5 to ide_get_best_pio_mode() despite supporting up to PIO4 only.

While at it, also:

- remove the driver's wrong claim about supporting SWDMA modes;

- stop hooking ide_dma_timeout() method as the handler clearly doesn't fit for
  the task...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fold the parts of the ide_dma_end() methods identical to __ide_dma_end() into a
mere call to it.
Start using faster versions of the ide_dma_end() and ide_dma_test_irq() methods
for the PCI0646U and newer chips that have the duplicate interrupt status bits
in the I/O mapped MRDMODE register, determing what methods to use at the driver
load time. Do some cleanup/renaming in the "old" ide_dma_test_irq() method too.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix several issues with the driver's procfs output:

- when testing if channel is enabled, the code looks at the "simplex" bits, not
  at the real enable bits -- add #define for the primary channel enable bit;

- UltraDMA modes 0, 1, 3 for slave drive reported incorrectly due to using the
  master drive's clock cycle resolution bit.

While at it, also perform the following cleanups:

- don't print extra newline before the first controller's dump;

- correct the chipset names (from CMDxxx to PCI-xxx)

- don't read from the registers which aren't used for dump;

- better align the table column sizes;

- rework UltraDMA mode dump code;

- remove PIO mode dump code that has never been finished;

- remove the duplicate interrupt status (the MRDMODE register bits mirror those
  those in the CFR and ARTTIM23 registers) and fold the dump into single line;

- correct the style of the ?: operators...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The IDE core looks at the wrong bit when checking if the secondary channel is
enabled on PCI0646 -- CNTRL register bit 7 is read-ahead disable, bit 3 is the
correct one.
Starting with PCI0646U chip, the primary channel can also be enabled/disabled --
so, add 'enablebits' initializers to each 'ide_pci_device_t' structure, handling
the original PCI0646 via adding the init_setup() method and clearing the 'reg'
field there if necessary...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The driver's ide_dma_test_irq() method was reading the MRDMODE register even on
PCI0643/6 where it was write-only -- fix this by always reading the "backward-
compatible" interrupt bits, renaming dma_alt_stat to irq_stat as the interrupt
status bits are not coupled to DMA.
In addition, wrong interrupt bit was tested/cleared for the primary channel --
it's bit 2 in all the chip specs and the driver used bit 1... :-/
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix the multiword DMA and drop the single-word DMA support (which nobody will
miss, I think).  In order to do it, a number of changes was necessary:

- rename program_drive_counts() to program_cycle_times(), pass to it cycle's
  total/active times instead of the clock counts, and convert them into the
  active/recovery clocks there instead of cmd64x_tune_pio() -- this causes
  quantize_timing() to also move;

- contrarywise, move all the code handling the address setup timing into
  cmd64x_tune_pio(), so that setting MWDMA mode wouldn't change address setup;

- remove from the speedproc() method the  bogus code pretending to set the DMA
  timings by twiddling bits in the BMIDE status register, handle setting MWDMA
  by just calling program_cycle_times(); while at it, improve the style of that
  whole switch statement;

- stop fiddling with the DMA capable bits in the speedproc() method -- they do
  not enable DMA, and are properly dealt with by the dma_host_{on,off} methods;

- don't set hwif->swdma_mask in the init_hwif() method anymore.

In addition to those changes, do the following:

- in cmd64x_tune_pio(), when writing to ARTTIM23 register preserve the interrupt
  status bit, eliminate local_irq_{save|restore}() around this code as there's
  *no* actual race with the interrupt handler, and move cmdprintk() to a more
  fitting place -- after ide_get_best_pio_mode() call;

- make {arttim|drwtim}_regs arrays single-dimensional, indexed with drive->dn;

- rename {setup|recovery}_counts[] into more fitting {setup|recovery}_values[];

- in  the speedproc() method, get rid of the duplicate reads/writes from/to the
  UDIDETCRx registers and of the extra variable used to store the transfer mode
  value after filtering,  use another method of determining master/slave drive,
  and cleanup useless parens;

- beautify cmdprintk() output here and there.

While at it, remove meaningless comment about the driver being used only on
UltraSPARC and long non-relevant RCS tag. :-)
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fold the now equivalent code in the ide_dma_check() method into a mere call to
ide_use_dma().  Make config_for_dma() return non-zero if DMA mode has been set
and call it from the ide_dma_check() method instead of ide_dma_on().
Defer writing the DMA timings to the chip registers until DMA is really turned
on (and do not enable IORDY for DMA).
Remove unneeded code from the init_hwif() method, improve its overall looks.
Rename the dma_start(), ide_dma_check(), and ide_dma_lostirq() methods, and
also use more proper hwif->dma_command, fix printk() and comment in the latter
one as well.  While at it, cleanup style in several places.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Get rid of the 'pio_speed' member of 'ide_drive_t' that was only used by this
driver by storing the PIO mode timings in the 'drive_data' instead -- this
allows us to greatly  simplify the process of "reloading" of the chip's timing
register and do it right in sl82c150_dma_off_quietly() and to get rid of two
extra arguments to config_for_pio() -- which got renamed to sl82c105_tune_pio()
and now returns a PIO mode selected, with ide_config_drive_speed() call moved
into the tuneproc() method, now called sl82c105_tune_drive() with the code to
set drive's 'io_32bit' and 'unmask' flags in its turn moved to its proper place
in the init_hwif() method.
Also, while at it, rename get_timing_sl82c105() into get_pio_timings() and get
rid of the code in it clamping cycle counts to 32 which was both incorrect and
never executed anyway...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (46 commits)
  mmc-omap: Clean up omap set_ios and make MMC_POWER_ON work
  mmc-omap: Fix omap to use MMC_POWER_ON
  mmc-omap: add missing '\n'
  mmc: make tifm_sd_set_dma_data() static
  mmc: remove old card states
  mmc: support unsafe resume of cards
  mmc: separate out reading EXT_CSD
  mmc: break apart switch function
  MMC: Fix handling of low-voltage cards
  MMC: Consolidate voltage definitions
  mmc: add bus handler
  wbsd: check for data opcode earlier
  mmc: Separate out protocol ops
  mmc: Move core functions to subdir
  mmc: deprecate mmc bus topology
  mmc: remove card upon suspend
  mmc: allow suspended block driver to be removed
  mmc: Flush pending detects on host removal
  mmc: Move host and card drivers to subdirs
  mmc: Move queue functions to mmc_block
  ...

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
  ocfs2: Force use of GFP_NOFS in ocfs2_write()
  ocfs2: fix sparse warnings in fs/ocfs2/cluster
  ocfs2: fix sparse warnings in fs/ocfs2/dlm
  ocfs2: fix sparse warnings in fs/ocfs2
  [PATCH] Copy i_flags to ocfs2 inode flags on write
  [PATCH] ocfs2: use __set_current_state()
  ocfs2: Wrap access of directory allocations with ip_alloc_sem.
  [PATCH] fs/ocfs2/: make 3 functions static
  ocfs2: Implement compat_ioctl()

We used to BUG_ON() for a badly mapped IO port, which is certainly
correct, but actually made it harder to debug the case where the ATA
drivers had incorrectly mapped a nonconnected ATA port.

So make badly mapped ports trigger a WARN_ON(), and throw the IO away
instead (and return all ones for reads).  For things like broken driver
initialization - which is the most likely cause anyway - that should
mean that the machine comes up and is usable (at least that was the case
for the ATA breakage that triggered this patch).

It tends to be a whole lot easier to do a "dmesg" on a working machine
than to try to capture logs off a dead one.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.linux-nfs.org/pub/linux/nfs-2.6: (28 commits)
  NFS: Fix a compile glitch on 64-bit systems
  NFS: Clean up nfs_create_request comments
  spkm3: initialize hash
  spkm3: remove bad kfree, unnecessary export
  spkm3: fix spkm3's use of hmac
  NFS4: invalidate cached acl on setacl
  NFS: Fix directory caching problem - with test case and patch.
  NFS: Set meaningful value for fattr->time_start in readdirplus results.
  NFS: Added support to turn off the NFSv3 READDIRPLUS RPC.
  SUNRPC: RPC client should retry with different versions of rpcbind
  SUNRPC: remove old portmapper
  NFS: switch NFSROOT to use new rpcbind client
  SUNRPC: switch the RPC server to use the new rpcbind registration API
  SUNRPC: switch socket-based RPC transports to use rpcbind
  SUNRPC: introduce rpcbind: replacement for in-kernel portmapper
  SUNRPC: Eliminate side effects from rpc_malloc
  SUNRPC: RPC buffer size estimates are too large
  NLM: Shrink the maximum request size of NLM4 requests
  NFS: Use pgoff_t in structures and functions that pass page cache offsets
  NFS: Clean up nfs_sync_mapping_wait()
  ...

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (49 commits)
  [SCTP]: Set assoc_id correctly during INIT collision.
  [SCTP]: Re-order SCTP initializations to avoid race with sctp_rcv()
  [SCTP]: Fix the SO_REUSEADDR handling to be similar to TCP.
  [SCTP]: Verify all destination ports in sctp_connectx.
  [XFRM] SPD info TLV aggregation
  [XFRM] SAD info TLV aggregationx
  [AF_RXRPC]: Sort out MTU handling.
  [AF_IUCV/IUCV] : Add missing section annotations
  [AF_IUCV]: Implementation of a skb backlog queue
  [NETLINK]: Remove bogus BUG_ON
  [IPV6]: Some cleanups in include/net/ipv6.h
  [TCP]: zero out rx_opt in tcp_disconnect()
  [BNX2]: Fix TSO problem with small MSS.
  [NET]: Rework dev_base via list_head (v3)
  [TCP] Highspeed: Limited slow-start is nowadays in tcp_slow_start
  [BNX2]: Update version and reldate.
  [BNX2]: Print bus information for PCIE devices.
  [BNX2]: Add 1-shot MSI handler for 5709.
  [BNX2]: Restructure PHY event handling.
  [BNX2]: Add indirect spinlock.
  ...

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/dtor/input: (65 commits)
  Input: gpio_keys - add support for switches (EV_SW)
  Input: cobalt_btns - convert to use polldev library
  Input: add skeleton for simple polled devices
  Input: update some documentation
  Input: wistron - fix typo in keymap for Acer TM610
  Input: add input_set_capability() helper
  Input: i8042 - add Fujitsu touchscreen/touchpad PNP IDs
  Input: i8042 - add Panasonic CF-29 to nomux list
  Input: lifebook - split into 2 devices
  Input: lifebook - add signature of Panasonic CF-29
  Input: lifebook - activate 6-byte protocol on select models
  Input: lifebook - work properly on Panasonic CF-18
  Input: cobalt buttons - separate device and driver registration
  Input: ati_remote - make button repeat sensitivity configurable
  Input: pxa27x - do not use deprecated SA_INTERRUPT flag
  Input: ucb1400 - make delays configurable
  Input: misc devices - switch to using input_dev->dev.parent
  Input: joysticks - switch to using input_dev->dev.parent
  Input: touchscreens - switch to using input_dev->dev.parent
  Input: mice - switch to using input_dev->dev.parent
  ...

Fixed up conflicts with core device model removal of "struct subsystem" manually.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
  remove "struct subsystem" as it is no longer needed
  sysfs: printk format warning
  DOC: Fix wrong identifier name in Documentation/driver-model/devres.txt
  platform: reorder platform_device_del
  Driver core: fix show_uevent from taking up way too much stack

* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (59 commits)
  PCI: Free resource files in error path of pci_create_sysfs_dev_files()
  pci-quirks: disable MSI on RS400-200 and RS480
  PCI hotplug: Use menuconfig objects
  PCI: ZT5550 CPCI Hotplug driver fix
  PCI: rpaphp: Remove semaphores
  PCI: rpaphp: Ensure more pcibios_add/pcibios_remove symmetry
  PCI: rpaphp: Use pcibios_remove_pci_devices() symmetrically
  PCI: rpaphp: Document is_php_dn()
  PCI: rpaphp: Document find_php_slot()
  PCI: rpaphp: Rename rpaphp_register_pci_slot() to rpaphp_enable_slot()
  PCI: rpaphp: refactor tail call to rpaphp_register_slot()
  PCI: rpaphp: remove rpaphp_set_attention_status()
  PCI: rpaphp: remove print_slot_pci_funcs()
  PCI: rpaphp: Remove setup_pci_slot()
  PCI: rpaphp: remove a call that does nothing but a pointer lookup
  PCI: rpaphp: Remove another wrappered function
  PCI: rpaphp: Remve another call that is a wrapper
  PCI: rpaphp: remove a function that does nothing but wrap debug printks
  PCI: rpaphp: Remove un-needed goto
  PCI: rpaphp: Fix a memleak; slot->location string was never freed
  ...

* master.kernel.org:/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  [CRYPTO] padlock: Remove pointless padlock module
  [CRYPTO] api: Add ablkcipher_request_set_tfm
  [CRYPTO] cryptd: Add software async crypto daemon
  [CRYPTO] api: Do not remove users unless new algorithm matches
  [CRYPTO] cryptomgr: Fix parsing of nested templates 
  [CRYPTO] api: Add async blkcipher type
  [CRYPTO] templates: Pass type/mask when creating instances
  [CRYPTO] tcrypt: Use async blkcipher interface
  [CRYPTO] api: Add async block cipher interface
  [CRYPTO] api: Proc functions should be marked as unused

ps3av: Replace GNU extension `__FUNCTION__' by C99 `__func__'
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ps3fb: Replace GNU extension `__FUNCTION__' by C99 `__func__'
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ps3: Make `ps3videomode -v 0' (auto mode) work again
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ps3av:
  - Move the definition of struct ps3av to ps3av.c, as it's locally used only.
  - Kill ps3av.sem, use the existing ps3av.mutex instead.
  - Make the 512-byte buffer in ps3av_do_pkt() static to reduce stack usage.
    Its use is protected by a semaphore anyway.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ps3fb: kill superfluous zero initializations
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ps3av: Replace the kernel_thread and the ping pong semaphores by a singlethread
workqueue and a completion.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ps3fb: Use atomic_dec_if_positive() instead of bogus atomic_read()/atomic_dec()
combinations
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ps3fb: Replace the kernel_thread and the semaphore by a proper kthread, which
is simply woken up when the screen must be updated
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert kmap_atomic() in the non-highmem case from a macro to a static
inline function, for better type-checking and the ability to pass void
pointers instead of struct page pointers.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

net/rxrpc/af-rxrpc.ko needs csum_partial_copy_from_user
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The recent conversion from `memcpy' to `skb_copy_from_linear_data' removed a
few casts, which were needed to silence compiler warnings. Re-add them.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Kill resource_size_t warnings by casting resource_size_t to unsigned long when
formatting Zorro bus resources, as they are always 32-bit.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Install the built-in macsonic interrupt handler on both IRQs when using
via_alt_mapping. Otherwise the rare interrupt that still comes from the
nubus slot will wedge the nubus.

$ cat /proc/interrupts
auto       2:      89176 via2
auto       3:     744367 sonic
auto       4:          0 scc
auto       6:     318363 via1
auto       7:          0 NMI
mac        9:     119413 framebuffer vbl
mac       10:       1971 ADB
mac       14:     198517 timer
mac       17:      89104 nubus
mac       19:         72 Mac ESP SCSI
mac       56:        629 sonic
mac       62:    1142593 ide0

Version 1 of this patch had a bug where a nubus sonic card would register
two interrupt handlers. Only a built-in sonic needs both.

Versions 2 and 3 needed some cleanups, as Raylynn Knight and Christoph
Hellwig pointed out (thanks).
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a potential problem in the timeout handling: don't free the DMA buffers
before resetting the chip.

Also a trivial cleanup. Bring macsonic and jazzsonic into sync.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a race condition in the transmit code, where the dma interrupt could update
the free tx buffer count concurrently and wedge the tx queue.

Fix the misuse of the rx frame status and rx frame length registers: no more
"fifo overrun" errors caused by the OFLOW bit being tested in the frame length
register (instead of the status register), and no more missed packets due to
incorrect length taken from status register (instead of the frame length
register).

Fix a panic (skb_over_panic BUG) caused by allocating and then copying an
incoming packet while the packet length register was changing.

Cut-and-paste the reset code from the powermac mace driver (mace.c), so the NIC
functions when MacOS does not initialise it (important for anyone wanting to
use the Emile boot loader).

Cut-and-paste the error counting and timeout recovery code from mace.c.

Fix over allocation of rx buffer memory (it's page order, not page count).

Converted to driver model.

Converted to DMA API.

Since I've run out of ways to make it fail, and since it performs well now,
promote the driver from EXPERIMENTAL status. Tested on both quadra 840av and
660av.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the flakiness in the CUDA ADB driver on m68k macs (keypresses getting
wedged down or ADB just going AWOL altogether).

The only IRQ used by this driver is the VIA shift register IRQ. The PowerMac
conditional code disables the other VIA IRQ sources, so don't mess with the
other IRQ flags in the common code -- m68k macs need them.

When polling, don't disable local interrupts when we only need to disable the
CUDA interrupt.

Unless polling, don't clear the shift register IRQ flag. On m68k macs this
creates a race that often breaks CUDA ADB.

Tested on Quadra 840av and LC630 (both m68k); also Beige G3 (powerpc).
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a crash caused by requests placed in the queue with the completed flag
already set. This lead to some ADB_SYNC requests returning early and their
request structs being popped off the stack while still queued. Stack corruption
ensued or an invalid request callback pointer was invoked or both. Eliminate
macii_retransmit() and its buggy implementation of macii_write(). Have
macii_queue_poll() fully initialise the request queues.

Fix a bug in macii_queue_poll() where the last_req pointer was not being set.
This caused some requests to leave the queue before being completed (and would
also corrupt the stack under certain conditions).

Fix a race in macii_start that could set the state machine to "reading" while
current_req was null.

No longer send poll commands with the ADBREQ_REPLY flag -- doing that caused
the replies to be stored in the request buffer where they were forgotten
about.

Don't autopoll by continuously sending new Talk commands. Get the controller to
do that for us. This reduces the ADB interrupt rate on an idle bus to about 5
per second. Only autopoll the devices that were probed.

Explicitly clear the interrupt flag when polling.

Use disable_irq rather than local_irq_save when polling.

Remove excess local_irq_save/restore pairs.

Improve bus timeout and service request detection.

Remove unused code (last_reply, adb_dir etc) and unneeded code (prefix_len,
first_byte etc).

Change TIP and TACK to their correct names on this ADB controller (ST_EVEN and
ST_ODD).

Add some commentry.

Add a generous quantity of sanity checks (BUG_ONs).

Let m68k macs use the adb_sync boot param too.

Tested on Mac II, Mac IIci, Quadra 650, Quadra 700 etc.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>