menu "Hardware Drivers Config"

config SOC_APM32F091VC
    bool
    select SOC_SERIES_APM32F0
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    default y

menu "Onboard Peripheral Drivers"

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default y
            config BSP_USING_UART2
                bool "Enable UART2"
                default n
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif

    menuconfig BSP_USING_DAC
        bool "Enable DAC"
        default n
        select RT_USING_DAC
        if BSP_USING_DAC
            config BSP_USING_DAC1
                bool "Enable DAC1"
                default n
        endif

    menuconfig BSP_USING_ONCHIP_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        default n
        if BSP_USING_ONCHIP_RTC
            choice
                prompt "Select clock source"
                default BSP_RTC_USING_LSE

                config BSP_RTC_USING_LSE
                    bool "RTC USING LSE"

                config BSP_RTC_USING_LSI
                    bool "RTC USING LSI"
            endchoice
        endif

    menuconfig BSP_USING_I2C
        bool "Enable I2C BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C
            config BSP_USING_I2C1
                bool "Enable I2C1 BUS"
                if BSP_USING_I2C1
                    comment "Notice: PB10 --> 26; PB11 --> 27"
                    config BSP_I2C1_SCL_PIN
                        int "i2c1 scl pin number"
                        range 0 63
                        default 26
                    config BSP_I2C1_SDA_PIN
                        int "I2C1 sda pin number"
                        range 0 63
                        default 27
                endif
            config BSP_USING_I2C2
                bool "Enable I2C2 BUS"
                if BSP_USING_I2C2
                    comment "Notice: PA0 --> 0; PA1 --> 1"
                    config BSP_I2C2_SCL_PIN
                        int "i2c2 scl pin number"
                        range 0 63
                        default 22
                    config BSP_I2C2_SDA_PIN
                        int "I2C2 sda pin number"
                        range 0 63
                        default 23
                endif
            config BSP_USING_I2C3
                bool "Enable I2C3 BUS"
                if BSP_USING_I2C3
                    comment "Notice: PB0 --> 16; PB1 --> 17"
                    config BSP_I2C3_SCL_PIN
                        int "i2c3 scl pin number"
                        range 0 63
                        default 8
                    config BSP_I2C3_SDA_PIN
                        int "I2C3 sda pin number"
                        range 0 63
                        default 41
                endif
        endif

    menuconfig BSP_USING_SPI
        bool "Enable SPI"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI1
                bool "Enable SPI1"
                default n

            config BSP_USING_SPI2
                bool "Enable SPI2"
                default n
        endif

    menuconfig BSP_USING_TMR
        bool "Enable Timer"
        default n
        select RT_USING_HWTIMER
        if BSP_USING_TMR
            config BSP_USING_TMR1
                bool "Enable TMR1"
                default n

            config BSP_USING_TMR2
                bool "Enable TMR2"
                default n

            config BSP_USING_TMR3
                bool "Enable TMR3"
                default n

            config BSP_USING_TMR6
                bool "Enable TMR6"
                default n

            config BSP_USING_TMR7
                bool "Enable TMR7"
                default n

            config BSP_USING_TMR14
                bool "Enable TMR14"
                default n

            config BSP_USING_TMR15
                bool "Enable TMR15"
                default n

            config BSP_USING_TMR16
                bool "Enable TMR16"
                default n

            config BSP_USING_TMR17
                bool "Enable TMR17"
                default n
        endif

    menuconfig BSP_USING_PWM
        bool "Enable PWM"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM3
            bool "Enable timer3 output PWM"
            default n
            if BSP_USING_PWM3
                config BSP_USING_PWM3_CH1
                    bool "Enable PWM3 channel1"
                    default n

                config BSP_USING_PWM3_CH2
                    bool "Enable PWM3 channel2"
                    default n

                config BSP_USING_PWM3_CH3
                    bool "Enable PWM3 channel3"
                    default n

                config BSP_USING_PWM3_CH4
                    bool "Enable PWM3 channel4"
                    default n
            endif
        endif

    config BSP_USING_WDT
        bool "Enable Watchdog Timer"
        select RT_USING_WDT
        default n

endmenu

menu "Board extended module Drivers"

endmenu

endmenu