menu "Hardware Drivers Config"

config SOC_STM32H750IB
    bool
    select SOC_SERIES_STM32H7
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    default y

menu "Onboard Peripheral Drivers"

    config BSP_USING_QSPI_FLASH
        bool "Enable QSPI FLASH (W25Q256)"
        select BSP_USING_QSPI
        select RT_USING_SFUD
        select RT_SFUD_USING_QSPI
        default n

    config PHY_USING_LAN8720A
        bool

    menuconfig BSP_USING_ETH
        bool "Enable Ethernet"
        select RT_USING_LWIP
        select PHY_USING_LAN8720A
        default n

    config BSP_USING_LCD
        bool "Enable LCD"
        select BSP_USING_PWM
        default n

    config BSP_USING_ESP32
        bool "Enable ESP32"
        select BSP_USING_UART4
        select RT_USING_AT
        select AT_USING_CLIENT
        select AT_USING_SOCKET
        select PKG_USING_AT_DEVICE
        select AT_DEVICE_USING_ESP32
        default n
endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default y

            config BSP_USING_UART4
                bool "Enable UART4"
                default y
        endif

    config BSP_USING_QSPI
        bool "Enable QSPI BUS"
        select RT_USING_QSPI
        select RT_USING_SPI
        default n

    config BSP_QSPI_USING_DMA
        bool "Enable QSPI DMA support"
        default n

    menuconfig BSP_USING_I2C1
        bool "Enable I2C1 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C1
            config BSP_I2C1_SCL_PIN
                int "i2c1 scl pin number"
                range 1 216
                default 135
            config BSP_I2C1_SDA_PIN
                int "I2C1 sda pin number"
                range 1 216
                default 95
        endif

    menuconfig BSP_USING_PWM
        bool "Enable pwm"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM2
            bool "Enable timer2 output pwm"
            default n
            if BSP_USING_PWM2
                config BSP_USING_PWM2_CH2
                    bool "Enable PWM2 channel2"
                    default n
            endif
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n

            config BSP_USING_ADC2
                bool "Enable ADC2"
                default n

            config BSP_USING_ADC3
                bool "Enable ADC3"
                default n
        endif

    config BSP_USING_SDIO
        bool "Enable SDIO"
        select RT_USING_SDIO
        select RT_USING_DFS
        default n

    config BSP_USING_USBD
        bool "Enable OTGHS as USB device"
        select RT_USING_USB_DEVICE
        select BSP_USBD_TYPE_HS
        select BSP_USBD_SPEED_HS
        select BSP_USBD_PHY_ULPI
        default n

    source "../libraries/HAL_Drivers/Kconfig"

endmenu

menu "Board extended module Drivers"

endmenu

endmenu