/**
  *********************************************************************************
  *
  * @file    ald_pis.c
  * @brief   PIS module driver.
  *
  * @version V1.0
  * @date    27 Nov 2019
  * @author  AE Team
  * @note
  *
  * Copyright (C) Shanghai Eastsoft Microelectronics Co. Ltd. All rights reserved.
  *
  * SPDX-License-Identifier: Apache-2.0
  *
  * Licensed under the Apache License, Version 2.0 (the License); you may
  * not use this file except in compliance with the License.
  * You may obtain a copy of the License at
  *
  * www.apache.org/licenses/LICENSE-2.0
  *
  * Unless required by applicable law or agreed to in writing, software
  * distributed under the License is distributed on an AS IS BASIS, WITHOUT
  * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
  * See the License for the specific language governing permissions and
  * limitations under the License.
  *
  *********************************************************************************
  */

#include "ald_pis.h"

/** @addtogroup ES32FXXX_ALD
  * @{
  */

/** @defgroup PIS PIS
  * @brief PIS module driver
  * @{
  */
#ifdef ALD_PIS

/** @defgroup PIS_Public_Functions PIS Public Functions
  * @{
  */

/** @defgroup PIS_Public_Functions_Group1 Initialization functions
  * @brief Initialization and Configuration functions
  * @{
  */

/**
  * @brief  Create the PIS mode according to the specified parameters in
  *         the pis_handle_t and create the associated handle.
  * @param  hperh: Pointer to a pis_handle_t structure that contains
  *         the configuration information for the specified PIS module.
  * @retval Status, see @ref ald_status_t.
  */
ald_status_t ald_pis_create(pis_handle_t *hperh)
{
	if (hperh == NULL)
		return ERROR;

	assert_param(IS_PIS_SRC(hperh->init.producer_src));
	assert_param(IS_PIS_TRIG(hperh->init.consumer_trig));
	assert_param(IS_PIS_CLOCK(hperh->init.producer_clk));
	assert_param(IS_PIS_CLOCK(hperh->init.consumer_clk));
	assert_param(IS_PIS_EDGE(hperh->init.producer_edge));
	assert_param(IS_PIS_SIGNAL_MODE(hperh->init.producer_signal));

	__LOCK(hperh);
	hperh->perh = PIS;

	/* get location of consumer in channel and position of con0/con1
	 * accord to comsumer_trig information */
	hperh->consumer_ch  = (pis_ch_t)(hperh->init.consumer_trig & 0x0F);
	hperh->consumer_con = (pis_con_t)((hperh->init.consumer_trig >> 4) & 0x0F);
	hperh->consumer_pos = (1U << (uint32_t)((hperh->init.consumer_trig >> 8) & 0xFF));

	if (hperh->perh->CH_CON[hperh->consumer_ch] != 0) {
		__UNLOCK(hperh);
		return BUSY;
	}

	MODIFY_REG(hperh->perh->CH_CON[hperh->consumer_ch], PIS_CH0_CON_SRCS_MSK, ((hperh->init.producer_src) >> 4) << PIS_CH0_CON_SRCS_POSS);
	MODIFY_REG(hperh->perh->CH_CON[hperh->consumer_ch], PIS_CH0_CON_MSIGS_MSK, ((hperh->init.producer_src) & 0xf) << PIS_CH0_CON_MSIGS_POSS);

	if (hperh->init.producer_clk == hperh->init.consumer_clk) {
		MODIFY_REG(hperh->perh->CH_CON[hperh->consumer_ch], PIS_CH0_CON_SYNCSEL_MSK, PIS_SYN_DIRECT << PIS_CH0_CON_SYNCSEL_POSS);
		MODIFY_REG(hperh->perh->CH_CON[hperh->consumer_ch], PIS_CH0_CON_PULCK_MSK, (hperh->init.consumer_clk) << PIS_CH0_CON_PULCK_POSS);
	}
	else {
		if (hperh->init.producer_signal == PIS_OUT_LEVEL) {
			if (hperh->init.consumer_clk == PIS_CLK_PCLK1)
				MODIFY_REG(hperh->perh->CH_CON[hperh->consumer_ch], PIS_CH0_CON_SYNCSEL_MSK, PIS_SYN_LEVEL_ASY_APB1 << PIS_CH0_CON_SYNCSEL_POSS);
			if (hperh->init.consumer_clk == PIS_CLK_PCLK2)
				MODIFY_REG(hperh->perh->CH_CON[hperh->consumer_ch], PIS_CH0_CON_SYNCSEL_MSK, PIS_SYN_LEVEL_ASY_APB2 << PIS_CH0_CON_SYNCSEL_POSS);
			if (hperh->init.consumer_clk == PIS_CLK_SYS)
				MODIFY_REG(hperh->perh->CH_CON[hperh->consumer_ch], PIS_CH0_CON_SYNCSEL_MSK, PIS_SYN_LEVEL_ASY_AHB << PIS_CH0_CON_SYNCSEL_POSS);
		}

		if (hperh->init.producer_signal == PIS_OUT_PULSE) {
			if (hperh->init.consumer_clk == PIS_CLK_PCLK1)
				MODIFY_REG(hperh->perh->CH_CON[hperh->consumer_ch], PIS_CH0_CON_SYNCSEL_MSK, PIS_SYN_PULSE_ASY_APB1 << PIS_CH0_CON_SYNCSEL_POSS);
			if (hperh->init.consumer_clk == PIS_CLK_PCLK2)
				MODIFY_REG(hperh->perh->CH_CON[hperh->consumer_ch], PIS_CH0_CON_SYNCSEL_MSK, PIS_SYN_PULSE_ASY_APB2 << PIS_CH0_CON_SYNCSEL_POSS);
			if (hperh->init.consumer_clk == PIS_CLK_SYS)
				MODIFY_REG(hperh->perh->CH_CON[hperh->consumer_ch], PIS_CH0_CON_SYNCSEL_MSK, PIS_SYN_PULSE_ASY_AHB << PIS_CH0_CON_SYNCSEL_POSS);
		}
	}

	MODIFY_REG(hperh->perh->CH_CON[hperh->consumer_ch], PIS_CH0_CON_PULCK_MSK, hperh->init.consumer_clk << PIS_CH0_CON_PULCK_POSS);
	MODIFY_REG(hperh->perh->CH_CON[hperh->consumer_ch], PIS_CH0_CON_EDGS_MSK, hperh->init.producer_edge << PIS_CH0_CON_EDGS_POSS);
	hperh->check_info = hperh->perh->CH_CON[hperh->consumer_ch];

	/* enable consumer bit, switch pin of consumer */
	if (hperh->init.input_chan == PIS_CHAN_INPUT) {
		switch (hperh->consumer_con) {
		case PIS_CON_0:
			PIS->TAR_CON0 |= hperh->consumer_pos;
			break;
		case PIS_CON_1:
			PIS->TAR_CON1 |= hperh->consumer_pos;
			break;
		default:
			break;
		}
	}

	__UNLOCK(hperh);
	return OK;
}

/**
  * @brief  Destroy the PIS mode according to the specified parameters in
  *         the pis_init_t and create the associated handle.
  * @param  hperh: Pointer to a pis_handle_t structure that contains
  *         the configuration information for the specified PIS module.
  * @retval Status, see @ref ald_status_t.
  */
ald_status_t ald_pis_destroy(pis_handle_t *hperh)
{
	assert_param(IS_PIS(hperh->perh));

	if (hperh->check_info != hperh->perh->CH_CON[hperh->consumer_ch])
		return ERROR;

	__LOCK(hperh);

	CLEAR_BIT(PIS->CH_OER, (1U << (uint32_t)hperh->consumer_ch));
	WRITE_REG(hperh->perh->CH_CON[hperh->consumer_ch], 0x0);

	switch (hperh->consumer_con) {
	case PIS_CON_0:
		PIS->TAR_CON0 &= ~(hperh->consumer_pos);
		break;
	case PIS_CON_1:
		PIS->TAR_CON1 &= ~(hperh->consumer_pos);
		break;
	default:
		break;
	}

	hperh->state = PIS_STATE_RESET;
	__UNLOCK(hperh);

	return OK;
}
/**
  * @}
  */

/** @defgroup PIS_Public_Functions_Group2 Operation functions
  * @brief PIS output enable or disable functions
  * @{
  */

/**
  * @brief  Start the PIS output function.
  * @param  hperh: Pointer to a pis_handle_t structure that contains
  *         the configuration information for the specified PIS module.
  * @param  ch: The PIS channel enable output
  *	    This parameter can be one of the following values:
  *		@arg PIS_OUT_CH_0
  *		@arg PIS_OUT_CH_1
  *		@arg PIS_OUT_CH_2
  *		@arg PIS_OUT_CH_3
  * @retval Status, see @ref ald_status_t.
  */
ald_status_t ald_pis_output_start(pis_handle_t *hperh, pis_out_ch_t ch)
{
	assert_param(IS_PIS(hperh->perh));
	assert_param(IS_PIS_OUPUT_CH(ch));
	__LOCK(hperh);
	SET_BIT(PIS->CH_OER, (1 << (uint32_t)ch));
	__UNLOCK(hperh);

	return OK;
}

/**
  * @brief  Stop the PIS output function.
  * @param  hperh: Pointer to a pis_handle_t structure that contains
  *         the configuration information for the specified PIS module.
  * @param  ch: The PIS channel disable output
  *	    This parameter can be one of the following values:
  *		@arg PIS_OUT_CH_0
  *		@arg PIS_OUT_CH_1
  *		@arg PIS_OUT_CH_2
  *		@arg PIS_OUT_CH_3
  * @retval Status, see @ref ald_status_t.
  */
ald_status_t ald_pis_output_stop(pis_handle_t *hperh, pis_out_ch_t ch)
{
	assert_param(IS_PIS(hperh->perh));
	assert_param(IS_PIS_OUPUT_CH(ch));
	__LOCK(hperh);
	CLEAR_BIT(PIS->CH_OER, (1 << (uint32_t)ch));
	__UNLOCK(hperh);

	return OK;
}
/**
  * @}
  */

/** @defgroup PIS_Public_Functions_Group3 Peripheral State and Errors functions
  *  @brief   PIS State and Errors functions
  * @{
  */

/**
  * @brief  Returns the PIS state.
  * @param  hperh: Pointer to a pis_handle_t structure that contains
  *         the configuration information for the specified PIS module.
  * @retval ALD state
  */
pis_state_t ald_pis_get_state(pis_handle_t *hperh)
{
	assert_param(IS_PIS(hperh->perh));
	return hperh->state;
}

/**
  * @}
  */

/** @defgroup PIS_Public_Functions_Group4 modulate output functions
  *  @brief   PIS modulate output signal functions
  * @{
  */

/**
  * @brief  Config the PIS modulate signal function
  * @param  hperh: Pointer to a pis_handle_t structure that contains
  *         the configuration information for the specified PIS module.
  * @param  config: Pointer to a pis_modulate_config_t structure that
  *         contains the selected target (UART0,UART1,UART2,UART3 or
  *         LPUART0) how to modulate the target output signal.
  * @retval Status, see @ref ald_status_t.
  */
ald_status_t ald_pis_modu_config(pis_handle_t *hperh, pis_modulate_config_t *config)
{
	assert_param(IS_PIS(hperh->perh));
	assert_param(IS_PIS_MODU_TARGET(config->target));
	assert_param(IS_PIS_MODU_LEVEL(config->level));
	assert_param(IS_PIS_MODU_SRC(config->src));
	assert_param(IS_PIS_MODU_CHANNEL(config->channel));
	__LOCK(hperh);

	switch (config->target) {
	case PIS_UART0_TX:
		MODIFY_REG(hperh->perh->UART0_TXMCR, PIS_UART0_TXMCR_TXMLVLS_MSK, config->level << PIS_UART0_TXMCR_TXMLVLS_POS);
		MODIFY_REG(hperh->perh->UART0_TXMCR, PIS_UART0_TXMCR_TXMSS_MSK, config->src << PIS_UART0_TXMCR_TXMSS_POSS);
		MODIFY_REG(hperh->perh->UART0_TXMCR, PIS_UART0_TXMCR_TXSIGS_MSK, config->channel << PIS_UART0_TXMCR_TXSIGS_POSS);
		break;

	case PIS_UART1_TX:
		MODIFY_REG(hperh->perh->UART1_TXMCR, PIS_UART1_TXMCR_TXMLVLS_MSK, config->level << PIS_UART1_TXMCR_TXMLVLS_POS);
		MODIFY_REG(hperh->perh->UART1_TXMCR, PIS_UART1_TXMCR_TXMSS_MSK, config->src << PIS_UART1_TXMCR_TXMSS_POSS);
		MODIFY_REG(hperh->perh->UART1_TXMCR, PIS_UART1_TXMCR_TXSIGS_MSK, config->channel << PIS_UART1_TXMCR_TXSIGS_POSS);
		break;

	case PIS_UART2_TX:
		MODIFY_REG(hperh->perh->UART2_TXMCR, PIS_UART2_TXMCR_TXMLVLS_MSK, config->level << PIS_UART2_TXMCR_TXMLVLS_POS);
		MODIFY_REG(hperh->perh->UART2_TXMCR, PIS_UART2_TXMCR_TXMSS_MSK, config->src << PIS_UART2_TXMCR_TXMSS_POSS);
		MODIFY_REG(hperh->perh->UART2_TXMCR, PIS_UART2_TXMCR_TXSIGS_MSK, config->channel << PIS_UART2_TXMCR_TXSIGS_POSS);
		break;

	case PIS_UART3_TX:
		MODIFY_REG(hperh->perh->UART3_TXMCR, PIS_UART3_TXMCR_TXMLVLS_MSK, config->level << PIS_UART3_TXMCR_TXMLVLS_POS);
		MODIFY_REG(hperh->perh->UART3_TXMCR, PIS_UART3_TXMCR_TXMSS_MSK, config->src << PIS_UART3_TXMCR_TXMSS_POSS);
		MODIFY_REG(hperh->perh->UART3_TXMCR, PIS_UART3_TXMCR_TXSIGS_MSK, config->channel << PIS_UART3_TXMCR_TXSIGS_POSS);
		break;

	case PIS_LPUART0_TX:
		MODIFY_REG(hperh->perh->LPUART0_TXMCR, PIS_LPUART0_TXMCR_TXMLVLS_MSK, config->level << PIS_LPUART0_TXMCR_TXMLVLS_POS);
		MODIFY_REG(hperh->perh->LPUART0_TXMCR, PIS_LPUART0_TXMCR_TXMSS_MSK, config->src << PIS_LPUART0_TXMCR_TXMSS_POSS);
		MODIFY_REG(hperh->perh->LPUART0_TXMCR, PIS_LPUART0_TXMCR_TXSIGS_MSK, config->channel << PIS_LPUART0_TXMCR_TXSIGS_POSS);
		break;

	default:
		break;
	}

	__UNLOCK(hperh);
	return OK;
}
/**
  * @}
  */
/**
  * @}
  */
#endif /* ALD_PIS */
/**
  * @}
  */
/**
  * @}
  */